Related Manuals for Curtis SHG Series
Summary of Contents for Curtis SHG Series
- Page 1 USER GUIDE SHG Series Automatic Coffee Grinder READ AND SAVE THESE INSTRUCTIONS NOTICE TO INSTALLER: Please leave this booklet with the machine.
-
Page 2: Table Of Contents
............................................................................................................................................................................. Contact Information Wilbur Curtis Co., Inc. 6913 Acco Street | Montebello, CA 90640 US Phone: 323-837-2300 | Toll Free: 800-421-6150 Email: csrassistance@wilburcurtis.com | Web: www.wilburcurtis.com . - 4:00 . PT Email: techsupport@wilburcurtis.com 030118NC... -
Page 3: Fs48
KEY FEATURES/SPECIFICATIONS/SYSTEM REQUIREMENTS FS48 Key Features • Easy to Use - Fully automatic operation. • • Highly Accurate and Consistent Throw - For even distribution, dust reduction. • Constant, uniform grind. • Powerful 1/2 hp Motor - Equipped with safety circuit breaker. Coffee Grinder Single 1 PH 120 V... -
Page 4: Is3
INSTRUCTIONS could result in personal injury or void the warranty. • This appliance is designed for commercial use. Any service other than cleaning and preventive maintenance should be performed by an authorized Wilbur Curtis service technician. • serviceable parts inside. - Page 5 IMPORTANT SAFEGUARDS CE Requirements • This appliance must be installed in locations where it can be overseen by trained personnel. • • • • This appliance must not be cleaned by water jet. • instruction concerning use of the appliance in a safe way and if they understand the hazards involved. •...
-
Page 6: Ii24
INSTALLATION INSTRUCTIONS II24 WARNING: WARNING: properly grounded. IMPORTANT: Installation Instructions Installation Requirements • A secure surface capable of supporting the weight of the appliance. • For units without an attached cord set: Appropriately sized, UL listed, grounding type power cable to meet enough •... -
Page 7: Oi35
OPERATING INSTRUCTIONS OI35 The grinder is factory preset for optimal performance. Open the top cover and pour Close the lid. in whole coffee beans. the brew basket. Slide the brew basket all Push the START button on Wait for the grinder motor to the way back into the brew the right side of the unit. -
Page 8: Ci22
CLEANING INSTRUCTIONS CI22 WARNING: Disconnect the power cord before cleaning. WARNING: DO NOT immerse the grinder in water or any other liquid. Avoid spilling liquid into the grind housing during cleaning. NOTICE - Do not use cleaning liquids, compounds or powders containing chlorine (bleach) or corrosives. USE OF THESE PRODUCTS WILL VOID THE WARRANTY. - Page 9 ROUGH-IN DRAWINGS RD54 14.70 in [37.3 cm] 10.16 in [25.8 cm] 9.75 in 13.38 in [24.8 cm] [34.0 cm] 29.63 in [75.2 cm] 21.71 in [55.1 cm] SHG, ROUGH-IN DRAWING 030518NC...
- Page 10 ILLUSTRATED PARTS/RECOMMENDED PARTS IP92 SHG - Main Chassis - Exploded View Grinder motor assembly, see section IP96 SHG, ILLUSTRATED PARTS/RECOMMENDED PARTS 030118NC...
- Page 11 ILLUSTRATED PARTS LIST IP92 SHG - Main Chassis - Parts List ITEM # PART # DESCRIPTION ITEM # PART # DESCRIPTION WC-9129 COVER, TOP ASSY SHG/ILGSS WC-9141 BASKET HOLDER WC-3891 LABEL, SHG WC-9155 SPRING FOR BASKET HOLDER WC-1390 1 HARNESS ASSY, SHG-10 (NOT SHOWN) WC-4813 SCREW, 5/16x5/8 LONG SHOULDER WC-1392 2...
- Page 12 ILLUSTRATED PARTS LIST IP96 Grinder Motor Assembly Grinder Motor Assembly - Parts List ITEM # PART # DESCRIPTION ITEM # PART # DESCRIPTION WC-37283 KIT, GRINDER CHUTE DHG/ILGD/SH WC-9107-6 DISC, SHEAR COFFEE GRINDER 6PK MOTOR, SLICING GRINDER ASSY 120V SLG/DHG/ SCREW AND THRUST PIN, ADJUSTING ASSY WC-9135 WC-91015...
- Page 13 ELECTRICAL SCHEMATICS ES92 ELECTRICAL RATING TABLE # of Voltage Amps Hertz Model Conductor Wires SHG-10 50/60 SLG-10 50/60 ELECTRICAL RATING TABLE Voltage Amps Hertz # of Conductor PART # Model # Wires WD-SHG-30 SHG-30 50/60 WD-SLG-30 SLG-30...
- Page 14 TROUBLESHOOTING GUIDE TG26 WARNING: Electric Shock Hazard - the procedures in this TROUBLESHOOTING GUIDE are to be Troubleshooting Guidelines • ELECTRICAL SCHEMATIC. • Grinder Does Not Grind Coffee - Motor Does Not Run ELECTRICAL SCHEMATIC Grinder Does Not Grind Coffee - Motor Runs Replacing a Broken Shear Disk Coffee Too Course or Too Fine Grinder Adjustment Procedure...
- Page 15 TROUBLESHOOTING GUIDE TG26 Setting the Timer WARNING: Electric Shock Hazard - Ounces Ounces Seconds Seconds (Estimated) (Estimated) 10.0 11.3 TIMER SETTINGS IMPORTANT:...
- Page 16 TROUBLESHOOTING GUIDE TG29 Grinder Adjustment Procedure WARNING: Electric Shock Hazard - The grinder can be adjusted to make the ground coffee more Setting the Timer Adjustment screw Lock nut Replacing a Broken Shear Disk Housing Grinding burr/ worm feed Shear Look for something that could have gotten caught inside the drive Broken shear...
- Page 17 Return Merchandise Authorization (RMA): All returned equipment must be properly re-packaged in the original carton and received by Curtis within 45 days following the issuance of a RMA. NO UNITS OR PARTS WILL BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION (RMA).