INDEX 1.Safety information....................2 2.Skill specifications and Performance trait ............3 3.Control panel......................4 4.Attachment and Body size..................5 5.Distance,spot diameter and illumination diagram............6 6.Mounting and installation..................7 7.Power supply and signal connection..............8 8.Menu setting......................10 9.Channel function....................13 Circuit connecting diagram ................17 11.Troubeshooting....................18 12.Cleaning and maintenances................19 Duty exonerative and copyright protection ..............19 Congratulations on choosing our company product! We thank you for your custom.
SAFETY INSTRUCTIONS Notice: To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Our company will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual.
Skill specifications and Perfor mance trait ◎ Voltage:AC100~240V 50/60Hz. ◎ Maximum power consumption :190W ◎ LED chip:CREEN 3W, R、G、B、W. ◎ LED QTY:61PCS;(R :17PCS; G:17PCS; B:17PCS; W:10PCS) ◎ Chip drive current:950mA ◎ LED life:≥50000H ◎ Beam angle:Zoom function min.10°,max.50° ◎ Color:RGB Color system,soft and no flicker,Single ring can be controlled separateiy, fast marco color system ◎...
Mounting and installation Cautions: For added protection mount the fixtures in areas outside walking paths, seatingareas, and away from areas were unauthorized personnel might reach the fixture. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device's weight.
Power supply and signal connection 1. Power supply Use the professional plug to connect the projector and main power supply. Please pay attention to the voltage, frequency the same as the mentioned on the projector. Suggest each light has separately switched of the power supply so that could turn on or turn off each projector desultorily.
Page 10
2.Signal connection Please use the round 3/5-pin XLR plugs &sockets offered by menu facture to connect the first projector's output to the second projector' input and connect the second projector's output to the third device's input. And in the same way for the rest, eventually connect the last device's output, all the devices are together as the following figure.
Menu setting 1.Button operation ● ESC: Exit Button ; ● UP:Page up or increase; ● DOWN:Page down or reduce; ● ENTER:OK button DOWN ENTER 2.Menu operation Level 1 menu Level 2 menu Level 3 menu Level 4 menu note A . * * * Address code Settings S T A .
Page 12
Note Level 2 menu Level 3 menu Level 4 menu Level 1 menu R-W. No signal, bright red-white G-B. No signal, bright green-blue G-W. No signal, bright green-white DMX. F No signal, bright blue-white B-W. No signal, Built-in program 1 PRO.1 PRO.2 No signal, Built-in program 2...
Page 13
Note Level 1 menu Level 2 menu Level 3 menu Level 4 menu Dimmer D.000 Strobe S.000 R.000 G.000 Green MANU B.000 Blue White W.000 M.000 Macro Zoom Z.000 Keep Factory settings Factory default password:1111(Enter) SERV default...
Circuit connecting diagram Power in Switching power supply GF5241AS GF5241AS in put PL4803-XS VER:1.1 2008-09 Display board Dreiver board LED board LED OUTPUT DC48V INPUT 6103Z-CFG V1.1 20170511...
TROUBLE DISPOSE It is recommended some solution for some normal trouble shooting. Any inextricability problems should always be handling by the professional person. Disconnect the power supply before maintenance the light. ●LED off: 1.Please check if install the suitable voltage 2.Please check whether the led will reach the end of their life can explode;...
CLEANING AND MAINTENANCE ■ 1.In order to ensure the projector could work normally. It should be kept clean always .The lens should also be regularly cleaned to maintain an optimum light output. Do not use any type of solvent on lens. It will damage the projector.
Need help?
Do you have a question about the PL6103 and is the answer not in the manual?
Questions and answers