Philips CMP400/51 User Manual

Register your product and get support at
www.philips.com/welcome
A
a
CMP400
c
B
m l
EN User manual
RU Руководство пользователя
English 2. Your car power amplifier
Congratulations on your purchase, and welcome to Philips! To fully
benefit from the support that Philips offers, register your product at
1. Important
www.philips.com/welcome.
Introduction
Safety
With the amplifier, you can enjoy high quality sound performance with
powerful bass and beats.
• Read and understand all instructions before you use the apparatus. If damage
is caused by failure to follow instructions, the warranty does not apply.
• This unit is designed for negative ground (earth) 12 V DC operation only. What's in the box
A
• Use only the supplied mounting hardware for a safe and secure installation.
Check and identify the contents of your package:
• Do not connect any active speakers (with built-in amplifier) to the speaker
Amplifier
terminals of the unit. Doing so may damage the active speakers. a
• To ensure safe driving, adjust the volume to a safe and comfortable level.
Screw_4x25mm (x4)
b
• To avoid short circuit, do not expose the apparatus to rain or water.
Fuse (x2)
c
• Never expose the apparatus to direct sunlight, naked flames or heat.
• Clean the apparatus with soft, damp cloth. Never use substances such as Hi input connector (x1)
d
alcohol, chemicals or household cleaners on the apparatus.
Overview of the main unit
Notice
OUTPUT L/R
a
• Connect additional amplifier for additional speakers.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the
b FRONT INPUT L/R
packaging easy to separate into three materials: cardboard (box), polystyrene
• Connect car audio with RCA cable.
foam (buffer) and polyethylene (bags, protective foam sheet.)
FRONT INPUT LEVEL
c
Your system consists of materials which can be recycled and reused if disassembled
Adjust input level (0.3V to 6V).
•
by a specialized company. Please observe the local regulations regarding the
disposal of packaging materials, exhausted batteries and old equipment.
HI INPUT
d
Connect car audio with the supplied high input connector.
•
Any changes or modifications made to this device that are not expressly
approved by Philips Consumer Lifestyle may void the user's authority to FRONT FREQ
e
operate the equipment. • Adjust frequency of HPF or LPF from 30Hz to 400Hz.
2009 © Koninklijke Philips Electronics N.V. All rights reserved.
Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips
Electronics N.V. or their respective owners. Philips reserves the right to change products at any time
without being obliged to adjust earlier supplies accordingly.
C
b
d
D
a
FR FL
4 ohm speaker 4 ohm speaker
k j i h g f e d c b a
Динамик 4 Ом Динамик 4 Ом
FR FL b
FR FL
n o p
4 ohm speaker
Динамик 4 Ом
4 ohm speaker 4 ohm speaker
Динамик 4 Ом Динамик 4 Ом
f FRONT HPF/OFF/LPF
• Select High-pass-filter (HPF), Low-pass-filter(LPF) or OFF (flat)
mode.
PROTECT
g
Light in red when the PROTECTOR is activated.
•
POWER
h
Light in blue when power is turned on.
•
BASS BOOST
i
• Boost the frequencies at around 45Hz to a maximum of 12dB.
REAR HPF/OFF/LPF
j
• Select High-pass-filter (HPF), Low-pass-filter(LPF) or OFF (flat)
mode.
k REAR FREQ
• Adjust frequency of HPF or LPF from 30Hz to 400Hz.
l REAR INPUT LEVEL
• Adjust input level (0.3V to 6V).
m REAR INPUT L/R
B Connect car audio with RCA cable.
•
POWER (GND/REM/+12V)
n
• Connect +12V DC power cable, ground wire and remote wire.
Fuse: 20Ax2
o
p SPEAKER OUTPUT
• Connect to speakers or subwoofers.
3. Installation
Installation
C
You can mount the amplifier either under a seat or on the rear tray.
c
FR FL
4 ohm speaker 4 ohm speaker
Динамик 4 Ом Динамик 4 Ом
4 ohm speaker 4 ohm speaker
Динамик 4 Ом Динамик 4 Ом
8 ohm speaker 8 ohm speaker
Динамик 8 Ом Динамик 8 Ом
E
a
Left speaker
Л
Car audio unit
А
а
Right speaker
П а
HI INPUT
Purple White
П Б
Green Grey
З С
4 ohm speaker Green/Black Grey/Black
З / С /
Динамик 4 Ом
Purple/Black White/Black
П / Б /
Connect power
Note
• To avoid interference, do not place the amplifier too close to the car audio or 1
antenna.
• The supplied mounting screws are 25mm long. Make sure that the mounting
board is thicker than 25mm.
1
Place the unit on the location for installation.
2
Mark the positions of the four screw holes.
3
Drill the holes with driller of approximately 4mm in diameter.
4
Mount the unit with the supplied screws.
Connect speakers
•
D
Note
4. Use your power amplifier
• Use speakers with an impedance of 2 to 8 ohm (4 to 8 ohm when used as a
bridged amplifier).
• Match the "left", "right", "+" and "-" terminals correctly. Revised polarity may
degrade sound quality. Select crossover frequency mode
Option 1: Mono bridged mode: connect 2 speaker
a You can select crossover frequency mode as below:
Option 2: Stereo mode: connect 4 speakers
b
HPF (high-pass-filter) mode
Option 3: Tri-mode: connect 6 speakers
c
Connect car audio
E LPF (Low-pass-filter) mode
Option 1: High level input connection
a OFF (flat) mode
Connect the amplifier to your car audio with the supplied High level
input connector.
1
Option 2: Line input connection
b
Connect the amplifier to the car audio with a RCA cable (not supplied).
Option 3: Line output connection
c
Connect the amplifier to another amplifier.
b
c
Left speaker
Л
Right speaker
П а
Adjust frequency
F
You can adjust frequency of HPF or LPF from 30HZ to 400Hz.
Make the power connection as illustrated below:
GND socket.
• Connect the ground wire from the car to the
Note
• Connect the remote wire from the car audio to the REM socket.
• When the HPF/OFF/LPF switch is set at OFF position, the frequency adjustment
√ With this connection, you can turn on/off the amplifier
does not work.
with the car audio.
• Connect the power wire from the car battery to the +12V
1
Rotate FREQ to select frequency.
socket.
Adjust input level
Tip
You can adjust the input voltage from 0.3V to 6V.
If your car audio does not have remote output, connect the remote input
1
terminal (REM) to the accessory power supply. Rotate INPUT LEVEL to adjust input voltage.
Adjust bass boost
You can punch extra bass for 0 to 12dB.
1 Rotate BASS BOOST to punch for extra bass.
About the protector indicator
The amplifier has a built-in protection circuit to protect the transistors
Select this mode when mid-range speakers
and speakers when:
and tweeters are connected for high frequency
• The unit is overheated. Or
output.
• A DC current is generated. Or
Select this mode when woofer and subwoofer is
• The battery voltage is over low or over high. Or
connected for low frequency output.
• The speaker terminals are short circuited.
Select this mode when tri-mode speaker
connection is used. When the PROTECT indicator lights up in red, the unit shuts down
automatically. If this happens, please:
Slide HPF/OFF/LPF to the selected positon.
1 Take out the disc or tape and turn off the car audio.
2
Check the cause of the malfunction (see above).
3
If the amplifier has overheated, wait until the unit cools down
before use.
F
Car audio unit
А
FR FL
а
to a metal point of the car
LINE OUT К а а а
Л
less than 450 mm (18 in)
Remote output М 450 (18 )
В а ДУ
Car audio unit
А
Fuse (40 A)
а
П а а (40 А)
+12 V car battery
А а +12 В
G
Replace fuse
G
If there is no power, the fuse may be damaged and need to be replaced.
1 Pull out the damaged fuse.
2
Replace the fuse with the supplied fuses or to buy two fuses
that matches the voltage of the damaged fuse (20Ax2).
If the fuse gets damaged immediately after it has been replaced, there
may be an internal malfunction. In such case, consult your Philips dealer.
5. Product information
Note
• Product information is subject to change without prior notice.
Power Output (RMS)
- 4 ohm 50Wx4
- 4 ohm (bridged) 150Wx2
- 2 ohm 80Wx4
Total harmonic distortion 0.016%
Signal to noise ratio 106dB
Channel separation 50dB
Frequency response 5-100kHz
Input sensitivity 300mV-6V
Input impedance 22k ohm
Fuse rating 20Ax2
Dimensions (DxWxH) 54.4x336.5x240.2mm