Advertisement
Quick Links
Download this manual
See also:
User Manual
Register your product and get support at
CID3288
www.philips.com/welcome
ENG
Quick Start Guide
English
Mount in the dashboard
1
Note
Install the car audio
Check wire connection before you mount
•
These instructions are for a typical installation.
the unit into a car.
However, if your car has different requirements,
•
If preset radio stations are lost when the
make the corresponding adjustment. If you have
ignition key is turned OFF and then back ON,
any questions regarding installation kits, consult
reconnect the red leads crosswise to the
your Philips car audio dealer.
yellow ones.
Caution
1
If the car does not have an on-board drive
or navigation computer, disconnect the
This unit is designed for negative ground
•
negative terminal of the car battery.
(earth) 12 V DC operation only.
•
If you disconnect the car battery in
•
Always install this unit in the car dashboard.
a car that has an on-board drive or
Other locations can be dangerous as the
navigation computer, the computer
rear of the unit heats up during use.
may lost its memory.
•
To avoid short-circuit: before you connect,
•
If the car battery is not disconnected,
ensure that the ignition is off.
to avoid short-circuit, ensure that bare
Ensure that you connect the yellow and red
•
wires do not touch each other.
power supply leads after all other leads are
2
connected.
Take out the original car audio and keep
•
Ensure that all loose leads are insulated with
the screws.
electrical tape.
3
•
Ensure that the leads do not get caught
Mount the screw and buffer (supplied).
a
under screws orin parts that will move
4
Connect wires (see "Connect wires"
(e.g. seat rail).
section).
•
Ensure that all ground (earth) leads are run
5
Slide the unit into the dashboard until a
to a common ground (earth) point.
Use only the supplied mounting hardware
click sound is heard.
b
•
6
for a safe and secure installation.
Fix the unit onto the dashboard with
•
Improper fuses can cause damage or fire.
screws.
c
When you need to change the fuse, consult
7
a professional.
Reconnect the negative terminal of the car
battery.
Note on the power supply lead (yellow)
•
When you connect other devices to this
2
Connect wires
system, ensure that the rating of the car
circuit is higher than the total fuse value of
Caution
all the connected devices.
Notes on speaker connection
•
Ensure that all loose leads are insulated with
electrical tape.
•
Never connect speaker wires to the metal
body or chassis of the car.
1
Check the car's wiring carefully, then do the
•
Never connect speaker wires with stripes
to one another.
other connections:
1
a
b
c
2
Turn on
Touch [Settings].
3
Touch [Time].
»
The date/time setup menu is displayed.
Caution
•
Risk of road accidents! Never watch video or
adjust settings while you drive.
1
Press
to turn on the unit.
»
The available OSD (On-Screen Display)
languages are displayed.
Set date
1
Touch [Date].
2
Touch on the displayed date information.
»
A submenu is displayed.
2
Touch a language to select.
The OSD language is changed to the
»
selected language immediately.
»
To turn off the unit, press
for
3 seconds.
3
Touch
or
to set year, month and day.
Set date and time
Set clock mode
1
1
Touch [Time mode].
Touch the upper left corner to display main
menu.
2
Touch on [12H] or[24H] to select clock
mode.
•
If necessary, touch
in the middle right
side of the screen to display the 2nd
screen.
2
Yellow
Green
Blue
a
Gearbox
AV system
AUX
Set time
Use map
1
Touch [Time].
2
Touch on the displayed time.
Note
»
A submenu is displayed
.
•
You may need to upgrade the map before
using it (see "Upgrade the map" section)
1
Touch the upper left corner to display home
menu.
2
Touch [Navigation].
» The navigation menu is displayed in a
few seconds.
3
Touch
or
to set hour and minute.
Tip
•
When date/time is set, touch
to return to
main menu.
3
Refer to the map manual (in Chinese) to
Adjust screen
operate the navigation tool.
To turn off the screen
1
Press DISP for over 2 seconds
»
The screen is turned off.
»
To turn on the screen, press
DISP.
To adjust screen brightness
1
Press DISP.
Brightness bar is displayed.
»
2
Tip
Rotate TUNE/
SELECT to adjust the
value.
•
You can press
NAVI to enter/exit the navigation
system.
Yellow
Yellow
Radio antenna
GPS antenna
Optional accessory
Optional accessory
AV system
AUX
Amplifier
Remark:
a Connect the AV IN cabel to the AV IN socket on front panel.
1
Listen to Radio
Insert the disc into the disc slot with label
side facing up.
1
»
Play starts automatically.
Touch the upper left corner to display
home menu.
»
To remove the disc, press the
button.
2
When the disc is ejected, the unit
Touch [Radio].
»
switches to the previous source,
»
Band and frequency information is
if connected. Otherwise, the
displayed.
unit switches to [Radio] mode
automatically.
Play USB device
4
Note
•
Ensure that the device contains playable
3
Touch on FM or AM to select band:
content.
•
FM band options:
FM1, FM2, FM3
1
•
AM band options:
AM1, AM2
Open the USB door.
4
2
Briefly touch
or
to tune to a radio
Insert the USB device to the USB socket.
station by step.
Play starts automatically.
»
•
Touch
or
for over 1 seconds to
tune to a radio station automatically.
Note
•
To remove the USB device, switch to disc,
radio or other source first.
Play disc
3
You can play video, audio or images stored on the
following discs:
Play with Bluetooth device
•
DVD video, DVD-R, DVD-RW
•
VCD
•
Audio CD, CD-R, CD-RW
Pair the Bluetooth-enabled devices
Note
To connect your Bluetooth device to the unit, you
need to pair the device to the unit. Pairing needs
Ensure that the disc contains playable content.
•
only to be done once.
You can pair up to eight devices.
You can play DVD discs with the following region
1
codes:
Search for Bluetooth device with the device.
2
Select "CID3288" in the pairing list.
DVD region code
Country
3
Enter default password "0000".
China
»
if pairing succeeds. phone call record is
displayed.
3
4
a
b
Receive call
By default, all incoming calls are received
automatically.
1
If there is incoming call, [Incoming call...]
flashes on the screen. Speak into the
Bluetooth microphone.
Make a call
1
Pair the phone with the unit.
2
Touch the upper left corner to display the
home menu.
3
Touch [Bluetooth].
»
The Bluetooth menu is displayed.
2
When conversation ends, touch
(red)
to terminate the call.
Tip
•
You can select to receive calls manually by
set [Auto answer] to [Off] status.
4
Touch
or
to select the paired phone,
then touch
.
5
Touch
or
to search for phone number
from the following list:
Or touch
to dial number directly, then touch
to dial.
© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
CID3288_93_QSG_V1.0
Advertisement
