Table of Contents
Advertisement
EN
ELECTRICAL CONNECTION
WARNING : This operation must be perfomed
by a qualified technician
WARNING - THIS APPLIANCE MUST BE EARTHED.
The cooker must be connected by a qualified electrician
to a suitable double - pole control unit with a minimum
rating of 32A and a minimum contact clearance of 3mm,
which should be fitted adjacent to (but not above) the
cooker, in accordance with IEE regulations.
The power supply cable should conform to BS6004
with a conductor size of 4mm
FIRST TIME USE
DAILY USE
HOTPLATE
The hotplate lid is fitted with a safety device which cuts
off the gas supply to the hotplate burners unless the lid
is fully open. Do not use the safety device as a means
of controlling the hotplate burners.
The hotplate has two high speed burners and two
simmering burners which will accommodate pans
between 100mm (4") and 240mm (91/2") diameter. All
pans should be positioned centrally over the burners.
TO USE THE HOTPLATE
1. Remove any items or spillage from the top of the
lid and then raise it to its fully open position.
2. Push in and turn the control knob of the chosen
burner anti-clockwise to the large flame symbol.
Continue to press the ignition button until the sparks
light the gas.
For the models with the electronic ignition button (
), press the button and then turn the knob.
3. Turn the control knob anti-clockwise to reduce the
heat input. Only turn the control knob between the
large flame symbol and the small flame symbol
when adjusting the setting.
4. To turn off, turn the control knob fully clockwise to
the symbol O.
Each burner is fitted with a spark ignitor for lighting the
gas. To ensure rapid lighting of the burners every time
they are used, the ignitors must be kept clean and dry.
8
.
2
LEVEL
1 - 2 – 3
4 - 5
6 - 7
8 - 9
10
The control unit should be easily accessible in the event
of an emergency.
This appliance conforms to EN55014
regarding suppression of radio and television interference.
The cooker terminals are behind the cover at the rear
The mains cable must pass through the cable clamp and
the screws must be fully tightened. Sufficient cable should
be used to allow the cooker to be pulled out for servicing.
Ensure that the cover is fully closed and secure afterwards.
Take care not to trap the mains cable when pushing the
cooker into its final position.
Remove any food spillage or cleaning materials from
the ignitor using a small nylon brush such as a tooth
brush. Access to the ignitor can be achieved by lifting
off the loose burner parts carefully when the burners
are cool.
When the hotplate burner bodies and caps are
removed for cleaning, be careful not to drop any food
particles or cleaning materials into the burner bases, to
avoid the possibility of blocking the gas jets.
If aluminium based pans are used, a silvery deposit
may appear on the top edge of the pan support
fingers. See 'Cleaning and Maintenance' section for
cleaning information.
Models with Hob Gas Burner Safety Devices to
Prevent Leaks
These models can
be identified by
HOB GAS BURNER
the presence of
SAFETY DEVICE
the device itself.
! Since the hob
burners are
equipped with
a safety device,
you must hold the
control knob in for about 3-7 seconds after the burner
has been lighted to allow the gas to pass until the
safety thermocouple has heated.
COOKING TIPS
Ideal for softening butter, gently melting chocolate in
bagnemarie, thawing small portions, creaming risotto, keeping
warm small portions of just-cooked preparation
Ideal for slow-cook recipes (rice,sauces,roast,fish)
using liquids (water, wine, broth), and for creaming pasta,
maintaining a gentle boiling
Ideal for sautéing, stewing vegetables, cooking for longer
period, preheating accessories, cooking until creamy
Ideal for browning, starting to cook, bringing liquids to the boil
quickly, frying deep-frozen products, grilling meat and fish,
maintaining a lively boil
Ideal for rapidly increasing the temperature of food
or for heating up liquids ( water)
ELECTRONIC
LIGHTING DEVICE
Advertisement
Table of Contents
