Skil 0788 Original Instructions Manual page 6

c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
5) SERVICE
a)
person using only identical replacement parts.
This will ensure that the safety of the power tool is
SAFETY INSTRUCTIONS FOR RECIPROCATING SAWS
GENERAL
Be familiar with the controls and the proper use of the
tool
The user is responsible for accidents or hazards
occurring to other people or their property
PERSONAL SAFETY
This tool should not be used by people under the age
of 16 years
Do not work materials containing asbestos
(asbestos is considered carcinogenic)
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
bystanders); wear a dust mask and work with a dust
extraction device when connectable
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
Follow the dust-related national requirements for the
materials you want to work with
Wear protective glasses and hearing protection
Do not reach underneath the workpiece (the
proximity of the blade to your hand is hidden from your
sight)
Keep hands away from between the tool housing
and blade clamp A
Keep hands away from cutting area and the blade;
(the blade clamp can pinch your
keep your second hand on barrel grip B
hands are holding the saw, they can not be cut by the
blade)
Never hold piece being cut in your hands or across
your leg (it is important to support the work properly
to minimise body exposure, blade binding, or loss of
control)
Use clamps or other equipment to secure and
support the workpiece (holding the workpiece in your
hand or against your body may lead to loss of control)
Use protective gloves when removing the blade
from the tool (the saw blade may be hot after
prolonged use)
ELECTRICAL SAFETY
Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
Inspect the cord periodically and have it replaced by a
Only use an extension cord which is intended for
outdoor use and equipped with a watertight plug and
coupling-socket
Inspect the extension cord periodically and replace it,
if damaged (inadequate extension cords can be
dangerous)
Use completely unrolled and safe extension cords with a
When operating the tool use a residual current device
(RCD) with a triggering current of 30 mA maximum
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord (contact with a
"live" wire will also make exposed metal parts of the tool
"live" and shock the operator)
or call the local utility company for assistance
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
Do not run over, crush or pull the (extension) cord
Protect the (extension) cord from heat, oil and sharp
edges
source if the power supply cord or the extension cord
is cut, damaged or entangled (do not touch the cord
before disconnecting the plug)
ACCESSORIES
when original accessories are used
Do not use a dull or damaged blade (bent blades can
break easily or cause kickback)
BEFORE USE
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Ensure that blade clamp A
a cut (a loose clamp may cause the tool or blade to slip
with loss of control as a result)
lighting
DURING USE
Do not get distracted and always concentrate on what
you are doing
6
(if both
is tight before making