White Rodgers Emerson Blue Wireless Easy Install 1F98EZ-1621 Installation Instructions Manual page 6

CONFIGURE COMFORT INTERFACE FOR SYSTEM
‡ˆ‘”‡ ‘’‡”ƒ–‹‰ –Š‡ Š‡ƒ–‹‰ ƒ† …‘‘Ž‹‰ •›•–‡ ‡–‡” –Š‡ ‹•–ƒŽŽ‡” ‡— ƒ† …‘ ‰—”‡ –Š‡ ‘ˆ‘”– –‡”ˆƒ…‡ ˆ‘” –Š‡ •›•–‡
–‡”‹‰ ƒ† ƒ˜‹‰ƒ–‹‰ –Š‡ †˜ƒ…‡† •–ƒŽŽ‡” ‘ ‰—”ƒ–‹‘ ‡—
On the Home Screen Display, press and hold the Menu button for approximately 5 seconds to enter the Comfort Interface Options
‘ ‰—”ƒ–‹‘ ‡— ”‡•• ƒ† Š‘Ž† –Š‡ Menu button again for approximately 5 •‡…‘†• –‘ ‡–‡” –Š‡ †˜ƒ…‡† •–ƒŽŽ‡” ‘ ‰—”ƒ–‹‘
Menu. Press ‡š– „—––‘ –‘ •–‡’ –Š”‘—‰Š …‘ ‰—”ƒ–‹‘ ‡— ‹–‡•
Menu
‡ˆ‡”‡…‡ SS1 HP1 ‹•’Žƒ›‡†
Number MS2 HP2 ƒ…–‘”› ‡ˆƒ—Ž–
01
MS2
02


03

On
04
‡ƒ–
—š ‡ƒ–
05

CR Heat
06

CR A/C
07

CR Heat A/C
08
 —š ‡ƒ–
09

CA
10

† ‡ —
11

ID Hum
12

CL
13

CO
14
MS2 
FA Heat
15
MS2 
FA A/C
6
Press or
to select options Description
SS1 2 1
MS2 = Multi-Stage conventional (no heat pump)
HP1 = Single compressor
HP2 = 2 compressor 2 speed compressor
SS1 = Single Stage conventional (no heat pump)
ELE Gas setting: Furnace controls blower
Elec setting: Comfort Interface controls blower
GAS
B
"O" Energizes O/B reversing valve terminal in cooling
"B" Energizes O/B reversing valve terminal in heating
 ‡ƒ– —–‘  ™‹–…Š ‘ ‰—”ƒ–‹‘ ˆ‘” 1 or MS2
‡ƒ– ƒ 
‡ƒ–  
 —š ‡ƒ– —–‘  ™‹–…Š ‘ ‰—”ƒ–‹‘ ˆ‘” 1 or HP2
—š ‡ƒ– ƒ 
—š ‡ƒ–  

Heat cycle rate: Fast, Med, and Slow

Cool cycle rate: Fast, Med, and Slow

Heat Pump cycle rate: Fast, Med, and Slow
SL
Auxiliary cycle rate: Fast, Med, and Slow
On
 Enables active protection for the compressor. If the CA module sends alerts for condition
number #2, 3, 4, 6 or 7 the interface will cancel the call for cool to protect compressor. The
interface will blink setpoint and display "Call for Service" as well as the Comfort Alert numbers.
(see troubleshooting for Comfort Alert)

On
‡Š—‹†‹ ‡• ‹ „‘–Š Š‡ƒ– ƒ† …‘‘Ž ‘†‡• †‡’‡†‡– ‘ˆ ƒ …ƒŽŽ ˆ‘” Š‡ƒ– ‘” …‘‘Ž
OFF †‡ˆƒ—Ž– …ƒ…‡Ž• ‹†‡’‡†‡– †‡Š—‹†‹ …ƒ–‹‘ ‘’–‹‘ ‘ ”‡–—” –‘ †‡Š—  ’”‡••
past 80% —–‹Ž  ƒ’’‡ƒ”•
Selecting On energizes the DHM terminal(s) and fan terminal (G) when humidity is above the
†‡ Š—‹†‹ …ƒ–‹‘ •‡––‹‰ Š‹• ˆ‡ƒ–—”‡ ‹• ‘ˆ–‡ —•‡† ˆ‘” †‡Š—‹†‹ …ƒ–‹‘ •›•–‡• ‹†‡’‡†‡–
from the heating and cooling system.
Note: ‘— —•– Šƒ˜‡ –Š‡ ‡Š—‹†‹ …ƒ–‹‘ ˆ‡ƒ–—”‡ ƒ…–‹˜ƒ–‡† ‡‡ ‘‡‘™‡” ‘ ‰—”ƒ–‹‘
Menu #8)
On
—‹†‹ ‡• ‹ „‘–Š Š‡ƒ– ƒ† …‘‘Ž ‘†‡• †‡’‡†‡– ‘ˆ ƒ …ƒŽŽ ˆ‘” Š‡ƒ– ‘” …‘‘Ž
OFF †‡ˆƒ—Ž– …ƒ…‡Ž• ‹†‡’‡†‡– Š—‹†‹ …ƒ–‹‘ ‘’–‹‘
On ‡‡”‰‹œ‡• –Š‡  –‡”‹ƒŽ • ƒ† ˆƒ –‡”‹ƒŽ ™Š‡ Š—‹†‹–› ‹• „‡Ž‘™ –Š‡ Š—‹†‹ …ƒ–‹‘
setting. This feature is often used on steam systems and is independent from the call for heat or cool.
Note: ‘— —•– Šƒ˜‡ –Š‡ Š—‹†‹ …ƒ–‹‘ ˆ‡ƒ–—”‡ ƒ…–‹˜ƒ–‡† ‡‡ ‘‡‘™‡” ‘ ‰—”ƒ–‹‘
Menu #7)
On
  Will cause the interface to wait 5 minutes between cooling cycles. This is intended to help
protect the compressor from short cycling. Some newer compressors already have a time delay
built in and do not require this feature. Your compressor manufacturer can tell you if the lockout
feature is already present in their system. When the Comfort Interface compressor time delay
‘……—”• ‹– ™‹ŽŽ ƒ•Š –Š‡ •‡–’‘‹– ˆ‘” —’ –‘ ˜‡ ‹—–‡•
 
On
CO ON ’”‘˜‹†‡• ƒ †‡Žƒ› ‹ …‹”…—Žƒ–‘” ˆƒ ‘’‡”ƒ–‹‘ ƒˆ–‡” –Š‡ …‘’”‡••‘” –—”• ‘ ‘” ‘
When compressor turns on (for a call for heat in heat pump or a call for cool) the fan will be
†‡Žƒ›‡† ˆ‘” ˜‡ •‡…‘†• „‡ˆ‘”‡ –—”‹‰ ‘ –‘ ƒŽŽ‘™ –Š‡ ƒ‹” –‘ „‡ Š‡ƒ–‡† ‘” …‘‘Ž‡†
…‘’”‡••‘” –—”• ‘ ˆ‘” ƒ …ƒŽŽ ˆ‘” …‘‘Ž –Š‡ ˆƒ ™‹ŽŽ …‘–‹—‡ –‘ ”— ˆ‘”
additional cooling from the system.
 

ON - Will enable this feature if you need to rapidly heat your home. Manually changing the
setpoint by 3 degrees or more will enable all stages of heat.
OFF - May not bring on secondary rapidly because it allows the Comfort Interface to compute
the optimum time to stage.

 Will enable this feature if you need to rapidly cool your home. Manually changing the
setpoint by 3 degrees or more will enable all stages of cool.

the optimum time to stage.
2 1. If longer cycles are desired, set to SL.
2 1
1
1
Will disable the active protection for the compressor
Will disable the feature
There will be no delay in fan operation
May not bring on secondary rapidly because it allows the Comfort Interface to compute
2)
2
ˆ–‡” –Š‡
•‡…‘†• –‘ …ƒ’–—”‡