Page 1
TANDBERG Telepresence T3 systEm AssEmbly GuidE 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 1 / 5 8...
Page 2
Whilst all reasonable care has been taken to ensure that the information contained in the presentation is accurate and not misleading, Tandberg shall not be liable for any loss resulting from reliance placed on the information contained in this document.
This document shows the assembling of the TANDBERG T3 system. References to left, center and right parts are shown in illustration below. 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAGE 3 / 5 8 systEm AssEmbly GuidE ContEnts Ceiling lights ...4 Light mounting details ...6...
The lights are to be connected to a switch as described in the document TANDBERG Telepresence T3—Room Requirements. Power supply requirements can be found in the document TANDBERG Telepresence T3—Room Requirements. ⁄ ” from the 228 cm 7’...
Page 5
TANDBERG Telepresence T3 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 5 / 5 8 CEilinG liGhts note! These items are included in the Immersive Room Package. What to unpack: Unpack the box marked • Main Lighting T3 box contents: •...
Make sure power is disconnected before any cables are connected or disconnected. 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 8 / 5 8 tAblE floor struCturE Unpack the box marked ’T3 Table Floor Structure and brackets’. The box contains the parts shown in the below Fig.
Page 9
119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 9 / 5 8 tAblE floor struCturE do as follows: Begin by placing the ‘bottom frame center’...
Page 10
TANDBERG Telepresence T3 8 × nut (a) M6 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 1 0 / 5 8 tAblE floor struCturE Unpack the bag containing screws, nuts and plates, located in the box marked T3 Brackets kit. Contents should be as follows: 62 pcs M6×10 (c)
Page 11
TANDBERG Telepresence T3 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 1 1 / 5 8 tAblE floor struCturE Please make sure that the distance to the wall is constant. If necessary, mark the position with a piece of tape or similar.
Page 12
2× nut (a) M6 note! The plates are shown upside down for clarity. 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 1 2 / 5 8 tAblE floor struCturE Fasten the Coverplate center to the coverplate front left, using the Joining plate and the Shims plate.
Page 13
TANDBERG Telepresence T3 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 1 3 / 5 8 tAblE floor struCturE When the three plates have been mounted together, gently sink them onto the floor structure. do not step on the plates!
Retain the DVI to HDMI cable between monitor and codec plus three power cables. 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 1 4 / 5 8 bottom modulEs Unpack the left system and take out the left Bottom module. Dismount the top screw on the right side in addition to the cable hatch cover.
Page 15
TANDBERG Telepresence T3 bottom modulEs 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 1 5 / 5 8...
Page 16
4 × nut (b) M8 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 1 6 / 5 8 bottom modulEs Unpack the center system. Dismount the top screw and the cable hatch cover on both sides of the module.
Page 17
119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 1 7 / 5 8 bottom modulEs Unpack the right Bottom module. Dismount the top screw and the cable hatch cover on the left side of the module, in addition to the same cables which were disconnected in the Left module, i.e.:...
Page 18
TANDBERG Telepresence T3 6 × nut (g) 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 1 8 / 5 8 bottom modulEs For the left Bottom module, get the splitter brackets shown above. Fasten them using 3 pcs M6 flange nuts as shown below. Then place the HDMI splitter between the brackets.
Column cover 2× Doorcover 4 × nut (b) M8 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 1 9 / 5 8 tAblE Column AssEmbly Unpack the box marked ‘Table column Assembly’ note! The Column covers and the Door covers shall not be mounted yet, so please place them in a spot where they won’t be damaged.
TANDBERG Telepresence T3 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 2 2 / 5 8 mountinG thE Column trAy When you have finished cabling the floor structure slide the Column tray into place as shown below. The column tray is found in the box marked ’T3 Table...
TANDBERG Telepresence T3 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 2 3 / 5 8 mountinG thE monitor AssEmbliEs Before you start mounting the monitors, the following cables must be con- nected: Cable 117850 to the left dnAm Cable 117852 to the center dnAm...
Page 24
TANDBERG Telepresence T3 12 × screw (e) M10×30 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 2 4 / 5 8 mountinG thE monitor AssEmbliEs Unscrew the top side screw of the monitor assembly on the right side of the left module, both sides of the center module and the left side of the right module.
Page 25
TANDBERG Telepresence T3 4 × M4 × 40 4 × M4 × 12 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 2 5 / 5 8 mountinG thE monitor AssEmbliEs Put the Center- and the Right monitor assemblies in place.
DIP switches to 1080p60 when used in countries with 60Hz line frequency—see the table on the camera’s underside. 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 2 6 / 5 8 mountinG thE CAmErA do as follows: Open the top cover.
Page 27
TANDBERG Telepresence T3 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 2 7 / 5 8 mountinG thE CAmErA Locate the other end of the camera cable mounted to the monitor. Use the cable clamps to fasten the cable inside the bottom module and connect to the codec.
When cabling the system we recommend that you open the Center bottom module lid completely as shown below. Note that the Left and Right modules must have been shut before you do this. 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 2 8 / 5 8...
Accessories box. Do not use other cloths! 8× screw (c) M6×10 12× nut (a) M6 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 3 5 / 5 8 tAblE toP modulE Carefully unpack the box labeled ‘T3 Table Top Module’, where the following items are found: •...
Page 36
TANDBERG Telepresence T3 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 3 6 / 5 8 tAblE toP modulE Insert the wooden plugs in the sides of the left table top. Lift Table top center and slide the steel profiles into the Table top left. Insert...
Page 37
8× screw (c) M6×10 12× nut (a) M6 6× screw (c) M6×10 20 × nut (b) 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 3 7 / 5 8 tAblE toP modulE Drop the right table top assembly to the column and fasten.
Page 38
TANDBERG Telepresence T3 4 × screw (c) 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 3 8 / 5 8 tAblE toP modulE Fit the two Table tighteners and tighten to remove the gap between the table top plates. Find the Cable channels and insert them in the hole of the center table top, slide them out to left and right, respectively.
TANDBERG Telepresence T3 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 3 9 / 5 8 CAblE ConnECtion dEtAils tAblE ConnECtions This is a complete drawing of the total cabling. It is available separately as a full size drawing. For your convenience...
TANDBERG Telepresence T3 tip! The connector blocks can be removed from the switch for more convenient connection. 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 4 8 / 5 8 tAblE ConnECtion notEs – – 117829 – 117828 – null-modEm rEquirEmEnt...
The table must have all cables mounted before the presentation screens are installed. 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 4 9 / 5 8 mountinG thE CollAborAtion sCrEEns Unpack the box marked with ’T3 Telepresence kit w/ TCU & screens’ where the following items are found: 3×...
Page 50
TANDBERG Telepresence T3 36 × screw (c) 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 5 0 / 5 8 mountinG thE CollAborAtion sCrEEns Connect all the cables to the monitor—see the cable schematics. set the power switch to on. note that this cannot be done after the screens have been installed.
Page 51
If you source such cables locally, make sure they are approved! 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 5 1 / 5 8 mountinG thE CollAborAtion sCrEEns While holding the Cable well, thread the audio, VGA and ethernet cables into the opening of the well.
Page 52
TANDBERG Telepresence T3 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 5 2 / 5 8 mountinG thE CollAborAtion sCrEEns Mount the covers A and B for the cable well. Find the Table quick buttons modules and make sure to configure the small switches found in the back.
Page 53
TANDBERG Telepresence T3 6 pcs Screw M3×10 (j) 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 5 3 / 5 8 mountinG thE CollAborAtion sCrEEns Connect the D-SUB cables to the SSTB, the microphone cables to the micro- phone and place it in on top of the bracket.
Otherwise you will not be able to fasten the screws completely! 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 5 4 / 5 8 mountinG thE tCu Unscrew the screws holding the brackets (marked in orange in picture be- low) in the left column.
Page 55
TANDBERG Telepresence T3 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 5 5 / 5 8 mountinG thE tCu Unscrew the screws holding the bracket in the right Column. Switch on the Presentation input switch before mounting. Make sure the DIP switch is set...
Page 56
TANDBERG Telepresence T3 4 × screw (f) M4×12 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 5 6 / 5 8 mountinG thE tCu Fasten the End cover plates to the Left and Right cover plates, using 2 f screws for each plate.
Page 57
TANDBERG Telepresence T3 mountinG thE tCu Snap the Door covers into place. 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 5 7 / 5 8...
Page 58
TANDBERG Telepresence T3 119078.01 TELEPRESENCE T3 SYSTEM ASSEMBLY 12.08 PAG E 5 8 / 5 8...