Good Earth Lighting UC1304-WH1-12LFW-G Quick Start Manual

ON/OFF Rocker Switch
Access Cover
Interrupteur à bascule
Couvercle pour l'accèsr
Interruptor oscilante
Cubierta de acceso
de encendido/apagado
Plastic screw cover
Caches des vis
Cubiertas de tornillo
WARNING: SHUT OFF POWER AT THE CIRCUIT BREAKER OR FUSE PANEL BEFORE REMOVING THE OLD
FIXTURE OR INSTALLING A NEW ONE.
IMPORTANT SAFETY INFORMATION
READ ENTIRE INSTALLATION PROCEDURE BEFORE
YOU BEGIN!
THIS FIXTURE IS DIMMABLE USING THE GOOD
EARTH LIGHTING APP.
(INSTRUCTION SHEETS INCLUDED)
If unsure if the electrical box is properly grounded, or the box is plastic
and has no ground wire, or are unfamiliar with the methods of properly
grounding fixture, consult a qualified electrician.
TURN POWER OFF AT BREAKER BOX/FUSE BOX. TURN WALL SWITCH TO JUNCTION BOX OFF
Remove the access cover by loosening the locking screw and slide the keyhole slot over the screw head, until it reaches to the large end of the
keyhole slot. As the access cover is removed from the fixture, the ends of the wires/wire connectors will be pulled out with it. Carefully, pull the ends
out about 3 inches and clip the zip tie that is attaching them to the access door.
Determine which corresponding knock-out is closest to the supply wire feed and remove it. CAREFULLY REMOVE THE KNOCK-OUT BY
HAMMERING A FLAT HEAD SCREWDRIVER OR PUNCH UNTIL THE SURFACE BREAKS. If the knock-out did not break free, use pliers (not
included) and bend it back and forth until it snaps off.
Option A (NM Cable): Attach the round plastic strain relief (CC) by pushing the wedge base into the knock-out hole until it locks into position. Push
the NM cable through the strain relief, allowing enough wire length to make the connections.
Option B (Flexible Whip): Attach the metal strain relief (BB) to the end of the flexible whip and turn until the strain relief (BB) is fully engaged with
the end of the cable. Push the strain relief (BB) and cable into the knock out and lock into position (allow enough wire length to make the connection).
Fixture must be properly grounded. Insert ground supply lead into connector on ground fixture wires.The ground wires can be either green or bare
copper. Insert black supply lead into connector on black fixture wires and white supply lead into connector on white wires.
Push excess wire into the wire compartment. Re-attach the access cover by sliding the access cover away from the screw head until the screw head
is captured by the narrow end of the keyhole slot. Tighten the locking screw back down.
OPTIONAL WIRING METHOD
RAMPE D'ÉCLAIRAGE À DEL À INSTALLER SOUS UNE ARMOIRE (Page 3)
Pre-installed Captive Screws
Vis captives installées préalablement
Tornillos cautivos preinstalados
Diffuser Pairing Button
Diffuseur
Bouton d'appariement
Difusor Botón de emparejamiento
WARNINGS AND CAUTIONS
1. Do not look directly at exposed LEDs for extended period of time.
2. LEDs gradually emit less light over their lifetime.
3. Do not use in wet locations. FOR INDOOR USE ONLY.
4. Do NOT mount to surfaces less than ¼ in.
5. For electrical requirements, see fixture. Minimum 90°C supply conductors.
6. Do NOT mount over sinks or stoves.
7. Do NOT install these lights inside of enclosed cabinets.
8. Turn power off before servicing.
9. Do not leave bare wires exposed.
10. Not intended for recessed installation in ceiling or soffits.
11. Maximum number of fixtures per run must not exceed maximum power supply
INSTALLATION
OPTION A
CCx1
BARRA CON LUZ LED PARA DEBAJO DEL GABINETE (Página 5)
Model / Model / Modelo # UC1304-WH1-12LFW-G , UC1304-WH1-18LFW-G ,
UC1304-WH1-24LFW-G , UC1304-WH1-30LFW-G
AAx2
* Los aditamentos reales pueden diferir de los que se muestran en la ilustración.
Required/ Nécessaire/ Obligatorio
wattage rating of 360 W. (10 fixtures total)
OPTION B
BBx1
Optional Wiring method: To pass through wiring with power
feeding back out to the next fixture the following is provided. For NM
cable or Flexible whip, use a second strain relief and the second KO
in the access cover. Push the second set of wires into the
corresponding quick connect with black to black, white to white and
ground to ground.
LED UNDER CABINET BAR (Page 1)
Linking cord
Cordon de raccordement
Cable de enlace
BBx2 CCx2
* Actual hardware may differ from illustration.
* La quincaillerie incluse peut être différente de l'illustration.