Table of Contents
Advertisement
Quick Links
DogCare EDGE Ultrasonic Dog Trainer (Model: UT01) FAQ's
1. How do I charge the device?
a. Using the USB cable, attach one end to a power source and plug the other end bottom
of the ultrasonic dog trainer.
b. When the charging cable is correctly connected, the device will vibrate slightly and the
status light will turn red.
c. When the status light turns green it indicates that the device is fully charged.
d. It usually takes about 4 to 5 hours to fully charge. Typically, after it is charged, you can
use it for four months without having to recharge it.
e. If the power is ON while charging, the ultrasonic trainer will work normally.
2. Can you tell if the battery is low/empty?
a. When the battery is getting low the light will flash red every 5 seconds, indicating that
the device should be charged soon. When the low battery alert is on the device can still
work normally.
b. When the battery is empty the status light will no longer light up. Pressing any button
will result in the status light flashing red 4 times quickly. At this time the device can not
work normally and can only be used after charging.
c. The ultrasonic trainer uses a lithium battery which requires routine recharging to
achieve maximum battery life span. In case the device is unused for and extended
period of time you should be sure to fully charge the battery every 3 months to maintain
battery life.
3. How do I turn ON the ultrasonic trainer?
a. Push the ON/OFF switch to the ON position.
b. The device will vibrate slightly two times when turning on, and the status light will be
green and flash twice.
c. When ON, the status light will flash green every 5 seconds.
4. How do I turn the ultrasonic trainer OFF?
a. Push the ON/OFF switch down to the OFF position.
b. When the device is off. All buttons will be invalid.
EDGE
Ultrasonic Dog Trainer
(Model: UT01)
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Dog Care EDGE UT01
Summary of Contents for Dog Care EDGE UT01
- Page 1 EDGE Ultrasonic Dog Trainer (Model: UT01) DogCare EDGE Ultrasonic Dog Trainer (Model: UT01) FAQ’s 1. How do I charge the device? a. Using the USB cable, attach one end to a power source and plug the other end bottom of the ultrasonic dog trainer. b.
- Page 2 5. What modes does the ultrasonic trainer have? a. The ultrasonic trainer has two operation modes. Training mode and deterrent mode. i. Training Mode. 1. To assist in dog training make sure the device is on. When you press the Train button the device will emit a lower intensity ultrasonic sound to get your dog’s attention.
- Page 3 c. When your dog’s barking is bothersome to you or others, you can press train or deter. This emits a loud ultrasonic sound. When your dog hears this they will stop barking and search for the source of the sound. At this point, when your dog pauses from barking, you should immediately praise your pet or give them a treat or toy as a reward.
- Page 4 with the train mode first to test to what extent the dog reacts to the ultrasound. Some sensitive dogs may react more intensely to the sudden sound. The owner should comfort and reassure the dog. For most dogs, the sound simply gets their attention. b.
- Page 5 17. Does the device work on running dogs? a. The Ultrasonic Dog Trainer does work on dogs that are moving; however, if your dog runs too far beyond the 25ft range, it won’t hear the ultrasonic sound. b. If other dogs excitedly run towards you, they can hear the sound once within the 25ft range.
- Page 6 customer service hot-line is 833-220-1900 and the website is www.dogcareglobal.com. You can also follow our Facebook @dogcareglobal for online Q&A. Training • When you press the Train button the device will emit a lower intensity ultrasonic sound to get your dog’s attention. To encourage your dog’s training, you should reward your dog with treats, petting, and verbal praise.
- Page 7 Gently and briefly press either the train or deter button to operate the ultrasound. • To protect against an accidental long press of the buttons, the ultrasonic function will turn off automatically if either the train or deter button has been continuously pressed for over 1 minute.
Need help?
Do you have a question about the EDGE UT01 and is the answer not in the manual?
Questions and answers