Do you have a question about the Expedition HURES36 and is the answer not in the manual?
Questions and answers
Trevor Ford
May 29, 2025
Replacing the back tire innertube
1 comments:
Mr. Anderson
May 29, 2025
To replace the back tire inner tube on a HURTLE HURES36:
1. Use a 10x2 inner tube with a straight valve stem. 2. To remove the rear wheel, take off the scooter’s bottom deck plate. 3. Disconnect the motor wires to fully detach the wheel. 4. Alternatively, you may be able to repair or replace the inner tube without removing the wheel completely. 5. Refer to YouTube videos for Ninebot Max rear tire changes, as the process is similar (except the Max uses tubeless tires).
Inflate the new tube to 32–37 psi after installation.
Page 1
10 Inch Foldable Electric Scooter Upgraded Pneumatic Tire Foldable Commuter, 36Watts 2 Channel High Power MOSFET Amplifier Suitable for Adult with Protection LED Indicator...
For your driving Safety, please read this user manual carefully before using and ensure to be able to ride the scooter under correct guidance. Learning all the safety warning and tips listed in this manual that will be helpful for you to better control the scooter. TABLE OF CONTENTS Riding Safety Packing List...
Riding Safety 1. The HURES36 Foldable Electric Scooter is a recreational product. Before mastering riding skills, you need to practice. Seller is not responsible for any injuries or damage caused by a rider's inexperience or failure to follow the instructions in this document.
Page 4
8. Before each ride check for loose fasteners and damaged components. If the HURES36 Foldable Electric Scooter makes abnormal sounds or signals an alarm, immediately stop riding. Diagnose your HURES36 Foldable Electric Scooter via the App and call your dealer/distributor for service. 9.
12. As with any electronic device, use a surge protector when charging to help protect your HURES36 Foldable Electric Scooter from damage due to power surges and voltage spikes. Only use the supplied charger. Do not use a charger from any other di erent product models. What's in the Box: 13.
Diagram Electronic Throttle Snap Hook Bell Dashboard & Power Button Brake Lever Handlebar km/h mph Headlight Stem Quick Release Lever Folding Mechanism Charge Port Front Fork Buckle Rear Fender Drum Brake Brake Light Battery Hub Motor Compartment Kickstand www.PyleUSA.com...
1. Speedometer: Display the current speed of the HURES36 Foldable Electric Scooter, as well as to display error codes. 2. Modes: Three modes available. "ECO" for Energy saving mode (smooth acceleration, suitable for beginners), "D" for Standard mode and "S" for Sport mode (powerful, only recommended for skilled riders). 3.
1. Install the App and register/login. km/h mph ECO D S 4. Verify that your Foldable Electric Scooter can be powered on and o . First Ride There are safety risks when 2. Power ON the Electric Scooter. A blinking Wireless BT learning to ride the Electric Scooter.
“ Scan for Vehicle” to connect to your Charging 3. Click “Vehicle Electric Scooter. The Electric Scooter will beep when the connection is successful. The BT icon will stop blinking and remain illuminated. Charge port Vehicle Vehi cle Fans Moments Fans Momen ts Discover Di scover...
Learning to Ride 2. Stand on the footrest with one foot and push o with another foot to start gliding. Wear an approved helmet and other protective gear to minimize any possible injury. km/h mph ECO D S 3. Put your other foot on the footrest to keep both feet stable.
WARNINGS Failure to follow these instructions could lead to serious injury. 4. Slow down by releasing the throttle; and brake by squeezing the brake lever. 5. To turn, shift your body weight and turn the handle DO NOT ride the Electric Scooter in the rain. slightly.
Page 12
DO NOT press the throttle when walking with the Watch your head when passing through doorways. Electric Scooter. DO NOT keep your feet on the rear fender. Avoid contacting obstacles with the tire/wheel. www.PyleUSA.com...
Page 13
DO NOT ride on public roads, motorways, or highways. DO NOT carry heavy objects on the handlebar. DO NOT rotate the handle violently while driving at DO NOT ride the Electric Scooter with only one foot. high speed. www.PyleUSA.com...
Page 14
DO NOT touch the hub motor after riding because it DO NOT ride through puddles or other bodies of water. can get hot. The Electric Scooter is for one rider only. Do not carry DO NOT take your hands o the handlebar while any passengers.
Folding and Carrying Folding Safety Hook Snap Hook 1. Turn o your Electric Scooter. Turn the safety hook DO NOT ride up and down stairs or jump over obstacles. counterclockwise and open the quick release lever. 2. Align the snap hook and the buckle and hook them. 3.
Cleaning and Storage Battery Pack Maintenance Use a soft, wet cloth to wipe the mainframe clean. Do not store or charge the battery at temperatures Dirt hard to remove can be scrubbed with a toothbrush outside the stated limits (see Speci cations). and toothpaste, then cleaned with a soft, wet cloth.
Page 17
WARNING Do not attempt to disassemble the battery. Do not touch battery contacts. Do not dismantle or puncture the casing. Keep the battery contacts away from metal objects to prevent short circuit. Risk of re and electric shock. No user serviceable parts. Do not charge or use your battery if it is damaged or see trace of water.
Page 18
Questions? Issues? We are here to help! Phone: (1) 718-535-1800 Email: cs@hurtleusa.com...
Need help?
Do you have a question about the Expedition HURES36 and is the answer not in the manual?
Questions and answers
Replacing the back tire innertube
To replace the back tire inner tube on a HURTLE HURES36:
1. Use a 10x2 inner tube with a straight valve stem.
2. To remove the rear wheel, take off the scooter’s bottom deck plate.
3. Disconnect the motor wires to fully detach the wheel.
4. Alternatively, you may be able to repair or replace the inner tube without removing the wheel completely.
5. Refer to YouTube videos for Ninebot Max rear tire changes, as the process is similar (except the Max uses tubeless tires).
Inflate the new tube to 32–37 psi after installation.
This answer is automatically generated