Advertisement
Quick Links
1. Name of the product
LED Projector + wheel rotator
2. Product code
22611130
3. Colour
As pictured.
4. Short description
This LED projector is energy efficient, emits little heat and is virtually maintenance-free due to the
built-in LED lamp. This projector is extremely suitable to place on a sheet or shelf, but due to the
weight of 3.2 kg less suitable for hanging from the ceiling. Comes with magnetic wheel motor. With
85 mm lens.
5. Content
1x LED Projector
1x Wheelrotator
1x 12V DC Transformer with 2 meter cord.
6. Sensory stimulations
Sight
7. In Use
Read this user manual before commissioning. Find a suitable location for the projector, taking into
account the following:
This product requires a grounded outlet, in accordance with the specifications on the projector/
mentioned under point 10.
Make sure the projector is focused on a light surface without obstacles.
Do not place the projector at an angle of more than 90⁰, this may cause the effect and liquidwheel or
other accessories to fall out of the projector at risk of damage and/or injury.
Free ventilation must be possible around the projector, especially at the ventilation grille.
Do not place the projector too close to heat sources such as a radiator.
This product is meant to look at, and does not need to be touched other than when turning it on and
off. However, it may be necessary to touch the projector in the meantime in order to change effects
or liquids.
Mount the projector in a stable location that can support the weight of the projector and accessories,
even if the projector falls. For standing placement, use a central bolt and nut (min. 14 mm e.g.
M10x20mm) and fix the bracket with at least 2 screws e.g. 2x 40 mm (none wood screws).
Advertisement
Related Manuals for NENKO 22611130
Summary of Contents for NENKO 22611130
- Page 1 1. Name of the product LED Projector + wheel rotator 2. Product code 22611130 3. Colour As pictured. 4. Short description This LED projector is energy efficient, emits little heat and is virtually maintenance-free due to the built-in LED lamp. This projector is extremely suitable to place on a sheet or shelf, but due to the weight of 3.2 kg less suitable for hanging from the ceiling.
-
Page 2: Additional Information
Do not turn on the device when it has fallen, is damaged, has interference, or when the plug or cord is damaged. Use only accessories intended for this projector. Use of unsuaddressed accessories may result in accidents, injury or damage. If in doubt, please contact Nenko. -
Page 3: Technical Information
10. Technical information Size: 34,7L x 13,3W x 10,2H cm (22,8 cm including bracket) Power: 62 Watts maximum Voltage: 22-240V of 11-120V 50/60Hz 12VDC Output: 500mA maximum Bulb: 40W LED Module Average lifespan LED Module: 100.000+ hours Weight: 3.2 kg Lumens: 850 lumens (scherm) Colour:... - Page 4 Electrical connection - Make sure that plug and cord are not trapped. Make sure you can't trip over the loose cable. - This product should not be switched to an external switch such as a timer or a switch that turns on/off regularly.
- Page 5 LIGHT TOGGLE SWITCH POSITIONS O: the light is on. Press the external switch to turn off the light. As long as the switch is pressed, the light remains off. The light turns on or off depending on the previous switching position. Press the external switch to turn on or off.
- Page 6 Do not try to open the projector yourself and never touch the LED module – it may break! In case of problems, take the projector to a qualified mechanic (Nenko can advise you on this) To replace the fuse, turn off the device and let it cool sufficiently. Then you can replace the fuse with a fuse with the same specifications: t1AH/250V Ceramic 20 mm x 5mm diameter) The fuse can be found in the IEC panel on the back.