Warranty And Liability; Declaration Of Conformity; Environmental Protection, Disposal - Fein MBS16X Translation Of The Original Instructions

Clean the ventilation openings on the power tool at reg-
ular intervals using non-metal tools. The blower of the
motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.
Before putting into operation, check the mains connec-
tion and the mains plug for damage.
Recommendation: The tool should always be supplied
with power via a residual current device (RCD) with a
rated current of 30 mA or less.
Operating Instructions.
When a power tool is mounted that
WARNING
is not intended for use with the
magnetic drill stand/industrial drill stand, the magnetic
drill stand/industrial drill stand can tip over.
Only use non-water mixable coolants or oil as the cool-
ing agent.
Use the magnetic drill stand/industrial drill stand suita-
ble for the performance characteristics of your drive
motor.
Pay attention that the set-up surface for the magnetic
foot of the magnetic drill stand is flat, clean and rust-
free. Remove varnish and putty/filler layers.
Use the magnetic drill stand only with the magnetic foot
switched on.
When working with the magnetic drill stand on non-
magnetic materials, suitable FEIN fastening devices, such
as suction plate, vacuum plates or pipe drilling devices,
which are available as accessories, must be used.
Even when working on steel materials where the mate-
rial thickness is below 12 mm, the work piece must be
made thicker with an additional steel plate in order to
ensure the magnetic holding power of the magnetic drill
stand.
Connect the drive motor only to the socket outlet on
the backside of the magnetic drill stand.
The magnetic foot of the magnetic drill stand is moni-
tored by means of a power sensor. If the magnetic foot
is defective, the drive motor will not operate.
Remove the application tool from the drill hole only
while the motor is running.
Should the application tool become stuck in the mate-
rial, stop the drive motor and remove the application
tool by carefully turning it anticlockwise.
Remove the chips and the drilled core after each drilling
process.
Do not touch the chips with your bare hand.
Always use a chip hook.
When changing the application tool, pay attention not
to damage its cutting edges.
When core drilling layered material, remove the core
and the chippings after drilling each layer.
With a tool inserted, the drive motor may not
move downward by itself.
When moving the magnetic drill stand with the
drive motor mounted, the unit can tip over when
the magnet is switched off. Therefore, secure the mag-
netic drill stand with a lashing strap.
Repair and customer service.
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
tool. The total insulation of the power tool can be
impaired. Blow out the interior of the power tool via
the ventilation slots frequently with dry and oil-free
compressed air, and connect a residual current device
(RCD) on the line side.
When the magnetic drill stand's power supply cable is
damaged, it must be replaced using a specially prepared
power supply cable, available from your FEIN customer
service agent.
The current spare parts list of this product can be found
on the Internet under www.fein.com.
If required, you can change the following parts your-
self:
Application tools, chipping protector, capstan handle
with handle levers, holder of the drive motor

Warranty and liability.

The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your product may include only a
part of the accessories described or shown in this
Instruction Manual.

Declaration of conformity.

This CE declaration is only valid for European Union
and EFTA (European Free Trade Association) countries
and only for products intended for the EU- or EFTA
market. After placing the product on the EU market the
UKCA mark loses its mark validity.
The UKCA declaration is only valid for the Great
Britain market (England, Wales and Scotland) and only
for products intended for the Great Britain market.
After placing the product on the Great Britain market
the CE mark loses its mark validity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the
last page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH,
D-73529 Schwäbisch Gmünd

Environmental protection, disposal.

Packaging, worn out magnetic drill stands/industrial drill
stands and accessories should be sorted for environ-
ment-friendly recycling.
en
23