IMPORTANT!!! IT IS IMPERATIVE THAT YOU READ THE ENTIRE INSTALLATION AND OPERATING INSTRUCTIONS AND ADHERE TO THE SAFETY MEASURES DESCRIBED IN THIS DOCUMENT – DECOFLAME CANNOT BE HELD RESPONSIBLE FOR ANY DAMAGE CAUSED AS A RESULT OF NON-ADHERANCE TO THESE INSTRUCTIONS.
Vapour Burning Technology) can be operated via control panel. Alternatively, the burner can be oper- ated with a remote controller or via Bluetooth/Decoflame App, if these upgrades have been purchased. Naturally, safety is imperative when dealing with open fire. Please strictly adhere at all times to all safety measures described in this manual.
NB – We do not recommend to position TV screens or valuable paintings above the fireplace as the upwards drifting warm air might damage those. Should you still want to create a setting incorporating a TV above the fireplace, please follow the instructions below (Figure 3.1.1) or ask Decoflame for further advice.
Make sure that the wall cut-out and supports left and right below the baseplate of your Denver Basic™ burner are perfectly in level horizontally and all the corners of the cut-out are in a perfect 90 degree angle. For the specific dimensions, please refer to the detailed technical drawing of your Decoflame fireplace.
Please note that the electronically controlled Denver Basic™ needs an earthed connection to the mains in order to work. A power socket needs to be present inside the cut-out into which the fireplace will be fitted. wHEN INSTALLING YOUR DENVER BASIC™ BURNER YOU wILL NEED:...
5.2. wALL CONSTRUCTION install the Denver Baisc in an DO NOT! install the Denver Basic in install the Denver Basic in a open-wall construction, which a wall construction, which is open massive wall (made of bricks, stone closed above and below the fire- above and below fireplace.
STEP 2: Lift the Denver Basic™ burner carefully out of its packaging using the two straps. Place the Denver Basic™ carefully on a level surface. Do not tilt it. Move Denver Basic™ closer to the cut-out and insert the plug into the socket. If necessary, switch on the socket. Still holding the fire with the straps, carefully sink it into the cut-out.
Page 10
FILLING THE FUEL TANK ONLY ADULTS MAY OPERATE THE ELECTRONICS OF THE DECOFLAME DENVER BASIC™. In order to open the fuel lid, the fireplace needs to be plugged into a power socket. Press the button for the lid to unlock . Open the lid of the fuel inlet, insert the funnel into the hole and fill in bioethanol.
The warming-up phase will be shortened if the flame tray is still warm from its earlier operation. SAFETY LOCK Denver Basic™ has a built-in safety lock. When the fireplace is cold, simply press button to unlock the fuel lid. After the fireplace has been operating, the fuel inlet cannot be open until the flame is completely extinguished and the fireplace has cooled down (around 5-10minutes).
6.3. VIA BLUETOOTH / DECOFLAME APP 1. Download and install the Decoflame 4. Once you have selected your fireplace, App by scanning the QR code above cor- you can turn it on by pressing ‘START’. If the responding to your smart device’s operat- fireplace has already been turned on us- ing system.
DO NOT modify anything on your custom-made Decoflame bioethanol fireplace. 8. DISPOSAL AND RECYCLING The made to measure Decoflame bioethanol fireplace is made of aluminium, stainless steel, glass(es), copper, plastics and electronic components. If you wish to dispose of the appliance, please adhere to the regional rules and regulations.
Page 14
EMPTYING THE FUEL TANK MANUALLY It is imperative that the fuel tank is empty, if the fireplace needs to relocated, or if it needs to be sent to Decoflame for further technical assistance. In order to empty the fuel tank manually, please follow the steps below: 1.
® Decoflame ApS Stenholm 14 9400 Nørresundby Denamark tlf. +45 9630 4800 info@decoflame.dk www.decoflame.com RATING PLATE (find the same rating plate on the back of the fireplace) Decoflame reserves the right to make changes without notice.