Content Index ABBREVIATIONS & ACRONYMS ........................3 ABOUT THIS MANUAL ............................4 INTRODUCTION ..............................5 RELATED SERVICE INFORMATION ........................6 PRODUCT SPECIFICATION ............................51 ....................51 PECIFICATION USTOMER CCEPTANCE ............................. 53 PECIFICATION ............................... 72 ACKING LEVEL 1 CIRCUIT BOARD AND STANDARD PARTS REPLACEMENT ..........73 ..........................
Abbreviations & Acronyms A/D Converter Analog to Digital Converter CEL LABEL China Energy Label Digital Television Electromagnetic Interference HDMI High Definition Multimedia Interface NTSC National Television System Committee On Screen Display Phase Alternating Line RS232 Interface Between Data Terminal Equipment and Data Communications Equipment Employing Serial Binary Data Interchange...
About This Manual This manual contains information about maintenance and service of TOSHIBA products. Use this manual to perform diagnostics tests, trouble shoot problems, and align the TOSHIBA product. Important Only trained service personnel who are familiar with this TOSHIBA Product shall perform service or maintenance to it.
Introduction This section contains general service information, please read through carefully. It should be stored for easy access place. Important Service Information RoHS (2002/95/EC) Requirements – Applied to all countries require RoHS. The RoHS (Restriction of Hazardous Substance in Electrical and Electronic Equipment Directive) is a legal requirement by EU (European Union) for the global electronics industry which sold in EU and some counties also require this requirement.
1.2. Not-included specification and each product spec in this spec sheet apply correspondingly to the following each country standard and requirement of Buyer Model Market Customer Panel Chassis Remark Name place TOSHIBA LIFESTYLE PRODUCTS AND Japan S430HF44 V0 T430HVN01.2 MSD8220 Mstar SERVICES Europe COPORATION Australia 2.
Page 8
Note2:Component specRTC IC tolerance 3.2.1. Power sequence for Panel a) T430HVN01.2...
Page 9
3.3. Power board specification 3.3.1 General specification Item Unit Remark AC Power Voltage Note 1 Max. Input Current (S430HF44V0) Arms Based on AC 100V Standby Power Note 1 : Follow Spec Label is 100V~240V Follow Power board Spec is 90V~264V 3.3.2 Control Signal (S430HF44V0) Item Unit...
Page 10
Item Unit Remark High Level Low Level 4. Optical Specification Each part is tested as below without special appointment 4.1 Temperature: -Operating 0℃ ~ 40℃ -Non-operating -20℃ to +60℃ 4.2 Relative Humidity: -Operating 10 to 90% -Non-operating ≦ 90% 4.3 Power Voltage: Standard input voltage (AC100V~ 240V 50/60Hz) * Standard Voltage of each product is marked by models 4.4 Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.
Page 11
Fig.1 presents additional information concerning the measurement equipment and method. Values Parameter Symbol Unit Notes Min. Typ. Contrast Ratio 2,400 3,000 Surface Luminance (White) cd/m Luminance Variation δWHITE(9P) Response Time (G to G) Color Gamut NTSC Color Coordinates 0.653 0.330 0.317 Green 0.615...
Page 12
all pixels displaying white at center 5 location. The variation in surface luminance, _WHITE is defined (center of Screen) as: δHITE(9P)= Minimum(Lon1, Lon2,…,Lon9)/ Maximum(Lon1, Lon2,…Lon9) Response time Tr is the average time required for display transition by switching the input signal for five luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on Fv=60Hz to optimize.
Page 14
Yellow -16~1 Color 0~50 47 47 47 47 カラー 0~50 Saturatio 0~15 Magenta Saturatio 0~15 Blue Color Saturatio 0~15 カラー Cyan Saturatio 0~15 Green Saturatio 0~15 Yellow Saturatio 0~15 Backl ight 0~100 バッ 100 100 0~100 クラ イト 5000K~10000K, 13000K/100K step, Color Temperature Custom 1300...
Page 15
Blue Gain 0~2047 B ゲイン Gamma 2.2/ 2.4 / 2.2 2.2 2.2 ガンマ Native. Noise Off/Wea Reduction k/Middle Midd Midd Midd ノイズリ /Strong Middle Middle Middle Middle ダクショ オフ/中/ ン 強/弱 Adaptive Contrast On/Off アダプテ オン/オ On On On ィブコン フ...
Page 16
~235/自 動 H position 0~100 水平位置 V position 0~68 垂直位置 Clock 0~100 Gray out Gray out クロック VGA setting Phase VGA 設定 0~100 位相 Enable/Disable Auto Adjustment 有効にする/無 自動調整 効にする Auto 自動 Reset Picture Setting None 映像設定をリセット Standard/Dynamic/C Sound Style ustom Dynam Dynam...
Page 17
音声の み Audio Line In/HDMI 1 Line Line HDMI HDMI Line Line Source Line In/HDMI 1 音源 Reset Sound Setting None 音声設定をリセット 1. User can set 7 secheuler to decide the power on/off time, source, frequency. 2. User can set any time, date, source, frequency in each schedule 3.
Page 18
3. If user change source by input source OSD or RS232/LAN command, source will keep at user selected source(Don’t care Priority setting at this time until user selected source signal is lost ). If user selected source signal is lost, PID will search the active input source according to the setting of Signal Priority Check.
Page 19
source is USB, system will auto play USB function. 11.This function(Failover/Failback) is premised on working automatically basically. Usually, the source used by a primary is set as P1.It is a backup function to when the signal of P1 is lost. (Off means uart communication is changed to Control VGA port.(RD debug)
Page 20
No : exit the confirm OSD.) Restore Default None デフォルトに戻す (Restore the default value.) Landscape Landscape/Portrait (Set the OSD in landscape or portrait mode. Rotation 水平/垂直 The portrait OSD will turn landscape OSD right 90 OSD 回転 degree) English/ Menu French/German/Spanish/Italian/Sw Language edish/Japanese/CN_Chinese...
Page 21
イ below. -Delay time = Number of Monitor ID × 0.3 sec. -For example, as for the display in which Monitor ID was set as 5, power supply is turned on after 1.5 sec. System Model TD-E432...
Page 22
Informat Name モデル名 システ ム情報 Version ソフトウ ex. 1.01.00 ェアバー ジョン Version 1.05.00 LAN バー ジョン Address ex. 192.168.2.1 IP アドレ ス 5.1 LED indication 5.2 OSD control Panel (Keypad) Item Specification Remark Show menu OSD MENU Source Change to input source Volume up VOLUME + VOLUME -...
Page 25
5.3.1 Remote controller Key Item Specification Remark POWER Power ON/OFF PICTURE Picture mode DIGI Key 1 Use in IR Daisy Chain Mode DIGI Key 2 Use in IR Daisy Chain Mode DIGI Key 3 Use in IR Daisy Chain Mode DIGI Key 4 Use in IR Daisy Chain Mode DIGI Key 5...
Page 26
Item Specification Remark backward Backward Play Play media forward Forward PIP on/off No function Previous previous Stop Stop play Pause Pause media Next next 6. Connecter Pin Assignment Item Description Remark IR IN IR signal input(Infrared) Note 1 (3.5mm Mini Jack) IR OUT IR signal output(Infrared) AV in...
Page 27
Note1:IR Input/ IR Pass-Though / Line Input /Line Out Audio Input Line Out Pin No Name Pin No Name Left signal Left signal Right signal Right signal IR Input IR Pass-Though Pin No Name Pin No Name IR IN Select IR Out Select +3V3 No function...
Page 28
Note2:VGA In Pin No Name Pin No Name 5V (DDC) Green Blue N.C. N.C. DDC-SDA H-SYNC Red-GND V-SYNC Green-GND DDC-SCL Blue-GND...
Page 29
Note3:HDMI Input Pin No Name Pin No Name TMDS Data2+ TMDS Clock- TMDS Data2- N.C. TMDS Data1+ N.C. TMDS Data1- TMDS Data0+ +5 V Power TMDS Data0- Hot Plug Detect TMDS Clock+...
Page 30
Note4:DVI Input/DVI Output Pin No Name Pin No Name TMDS Data2- Hot Plug Detect TMDS Data2+ TMDS Data0- TMDS Data 2/4 shield TMDS Data0+ N.C. TMDS Data 0/5 shield N.C. N.C. DDC Clock N.C. DDC Data TMDS Data Clock shield N.C.
Page 31
Note5:USB Input Pin No Name VCC (+5V) Data - Data +...
Page 32
Note6:RS232C Input/RS232C Output Pin No Name N.C. N.C. N.C. N.C. N.C. N.C.
Page 33
Note7:RJ45 (LAN) Pin No Name TX_D1+ TX_D1- TX_D2+ TX_D3+ TX_D3- TX_D2- TX_D4+ TX_D4-...
Page 34
Note8:AV Input Component Composite Pin No Name Name RGB_RED RGB2_BLUE `RGB2_GREEN AV IN 7. Video specifications 7.1. General Specifications Item Unit Remark Over scan, Vertical Video Over scan, Horizontal Video Component Video Input Level (Y, C 75 ohm without Sync PC RGB Video Input Level 75 ohm without Sync PC H/V Input Level...
Page 35
7.2. Picture Quality The following faulty symptoms should not be recognized for all the signal inputs with commercial DVD player, and related equipment source. Signal Symptoms Remark 40 IRE ~ 100IRE -Noise, Beat Image should stay stable, and should not have noise. White Raster Pattern -Flicker Fail: image become flickers,...
Page 36
8. Audio specifications 8.1. Speaker Out Item Specifications Remark Audio Amplifier Output (8Ω Load) Maximum Audio iutput 5 W each channel @ 0.5Vrms input, 1kHz tone, THD < 10% Maximum Audio Output 5 W each channel @ 0.5Vrms input, 1kHz tone, THD < 10% 10% @ 0 ~ 0.5 Vrms input, 1 kHz tone PC input:0 ~ 1Vrms THD+N vs Power...
Page 37
8.2. Line out The following performance specifications are supported for analog stereo audio output: Item Specifications Remark Impedance Maximum Audio Output Variable mode 0.5Vrms, 1kHz tone, THD < 1% 1% @ 0 ~ 0.5 Vrms, 1 kHz tone PC input :0 ~ 1Vrms THD+N vs Power 1% @ 70% Max power, 20 Hz ~ 20 kHz THD+N vs Frequency...
Page 38
9. Mechanical Specifications 9.1. General Specification a) S430HF44 V0 六面図...
Page 39
Item Content Remark Width Length Height Unit Before Packing Product After Packing 1090 Dimension Only Set 10.5 With BOX 15.0 Container 20 ft 40 ft 40ft(HQ) Individual or Loading Palletizing Quantity Front Cover : ABS MT11020 Appearanc General Back Cover : ABS MT11020 b).Installation in portrait and landscape •...
Page 40
c) Operation environment for portrait and face down (between 0° and 15°) installation The following operation environment details apply when the display is installed in portrait and face up orientations. • Temperature 0 - 40°C / 32 - 104°F • Humidity 20 - 80% (without condensation) 9.2 Mechanical specification for GAP a) S430HF44V0 Standard...
Page 41
10. Safety 10.1. Test Method 10.1.1. Performance: Display test methods follow Darwin Public Information Display test items or Customer’s spec 10.1.2. Demanded other specification Model Market Appliance Compliance Note UL/cUL UL 60950-1, 2nd Edition FCC with 740 form (FCC CSA C22.2 No. 60950-1-07, 2nd logo) Edition *The LCD Display...
Page 42
Item Typ Max Unit Note 400Vrms (Cree 60950 page) 250Vrms (Cree Isolation Gap, page) Primary-Secondary 400Vrms (Cree page) It is Delta Power Board spec only for maximum loading (not a set spec) Main board: Power Consumption(power Board), 5.1V/4A,12.5V/4A Light Bar: 165V/320mA Tatol:154W Comply with...
Page 43
Item Typ Max Unit Note Sharp Edge IEC/EN/UL 60950-1/CSA C22.2 No. Safety UL/ cUL/CB/S-mark 60950-1-07, Compliance J60950-1(H22):2010 J3000(H25) FCC/PSE/CE/S-mark/RCM Class I Apparatus only. ≤0.1Ώ at 40A / 2min Earth Continuity Primary to PE 1. 40A / 2min.(CSA) Test (MP-3sec) 2. 32A / 2min. three times the weight of the Wall mount equipment but not less than...
Page 44
11.2. EMC Reliability Item Unit Remark ESD(EN61000-4-2) Follow EN61000-4-2 EFT/Burst (EN61000-4-4) Follow EN61000-4-4 Surge Immunity (EN61000-4-5) Follow EN61000-4-5 Voltage Dip Test, 10ms (EN61000-4-11) <95 Follow EN61000-4-11 Voltage Dip Test, 500ms(EN61000-4-11) Follow EN61000-4-11 Voltage Interruptions, 5s(EN61000-4-11) <95 Follow EN61000-4-11 CS(EN61000-4-6) Follow EN61000-4-6 dBμV EMI Test Follow EN55022...
Page 45
Item Unit Remark C Temperature Step Test (Portrait/Land Scope) 1. Mean measure ambient temperature. 2. Thermal profile measure Item : PCB/Cabinet inner C Thermal Profile Test and outside/power cord and AC plug 3. Portrait/Land Scope Condensation Test Transportation Test Overstress Test Durability Test 1.
Page 46
12. Accessory 12.1. Accessories a) S430HF44V0 Item P/N (Darwin) Unit Remark Battery 23.20000.010 AAA Type For US、EU、AU model 49.50S0R.002 User's manual For Japan model 49.43S04.003 For US、EU model 49.50S0R.001 Warranty Card For AU model 49.43S04.002 PE Bag 79.42S19.002...
Page 47
Cable Cramp 79.64S0J.P01 3RCA Cable 50.43S04.00E 3RCA Logo Cover Sheet 77.64S0J.002 Mylar (50 x10mm) Remote 49.43S04.001 For US model Power cord for USA 27.01118.00B For AU model Power cord for AU 27.01318.001...
Page 48
For Japan model Power cord for Japan 27.02318.001 For EU model Power cord for EU 27.00918.001 12.2. LABEL P/N – a) S430HF44V0 Item P/No Unit Remark On backlight module (shipping Module Label 82.39T08.001 Label75*23mm)
Page 49
Spec 82.50S0R.001 On Set Rear (170x80mm) Label(Rating) Energy Label 82.18S01.004 On Front Bezel (15*15mm) On Carton side (Carton Shipping Label 82.37S01.012 Label76x70mm)
Page 50
On Carton Front/Rear Model Label 82.24S19.005 (100x90mm) Serial Label 82.37S02.003 On Assy bag (50*12mm)
Customer Acceptance TD-E432 PID Customer Acceptance Criteria 1. SCOPE This document establishes the general workmanship standards and functional Acceptance criteria for LCD TV model 32RV5510 Produced by BV Inc. 2. PURPOSE The purpose of this publication is to define a procedure for inspection of the LCD TV by means of a customer acceptance test, the method of evaluation of defects and rules for specifying acceptance levels.
Page 52
D: thickness Outline Dimension 855.8(H) x 554.4 (V) x 64.2 (D) Include Wall mount scale Driver Element a-Si TFT active matrix Display Colors 8 bit (16.7M) Colors Number of Pixels 1,920*1,080 Pixel Pixel Pitch 0.49 (H) x 0.49(W) Pixel Arrangement RGB vertical stripe Display Operation Mode Normally Black...
6. Optical Specification Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a dark environment at 25°C. The values specified are at an approximate distance 500 mm from the LCD surface at a viewing angle of φ and Ө equal to 0°.. Fig.1 presents additional information concerning the measurement equipment and method.
Page 54
0.330 0.317 Green 0.615 0.153 Blue 0.060 0.290 White 0.292 θr x axis, right (φ=0 ° Degree θi x axis, left (φ=180 ° Viewing Degree θu y axis, up (φ=90 ° Angle Degree θd y axis, down (φ=270 ° degree Note: 6.
Page 55
FIG. 2 Luminance 5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG3.
Page 56
7. Interface Specification The S430HF44 V0 (96.43S04.001) requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The other is to power Back Light Unit. 7-1 Input power Item Symbol Unit Note...
Page 57
Note3. Measurement condition : Rising time = 400us Note4. The relative humidity must not exceed 80% non-condensing at temperatures of 40 ℃ or less. At temperatures greater than 40 ℃, the wet bulb temperature must not exceed 39 ℃. When operate at low temperatures, the brightness of LED will drop and the life time of LED will be reduced.
Page 58
Note1. Pin number start from the left side as the following figure. Note2. Please leave this pin unoccupied. It can not be connected by any signal (Low/GND/High). Note3. Input control signal threshold voltage definition...
Page 59
Note4. I2C Data and Clock I2C Data and Clock timing Input equivalent impedance of LVDE_SEL pin Note5. Write Protection...
Page 60
Note6. LVDS data format selection Note7. Please leave this pin unoccupied or connect to ground. It can not be connected by any signal (Low/High). 7-3 Input Data Format 4.3.1 Data mapping 4.3.1.1 LVDS LVDS Option for 10bit LVDS Option NS...
Page 61
LVDS Option = Low JEIDA 7.3.2 Color Input Data Reference The brightness of each primary color (red, green and blue) is based on the 10 bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.
Page 63
8. Signal Timing Specification 8-1 Input Timing This is the signal timing required at the input of the user connector. All of the interface signal timing should be satisfied with the following specifications for its proper operation. Timing Table (DE only Mode) Signal Item Symbol...
Page 65
8-2 Input interface characteristics Value Parameter Symbol Unit Note Tpy. Input Differential Voltage Differential Input High Threshold Voltage +100 +300 Differential Input Low Threshold Voltage -300 -100 Input Common Mode Voltage 1.25 Input Channel Pair Skew Margin -500 +500 SKEW (CP) LVDS Interface Input Channel Pair Skew Margin...
Page 66
Note3. LVDS Receiver Clock SSCG (Spread spectrum clock generator) is defined as below figures Note4. Receiver Data Input Margin...
Page 67
8-3 Power Sequence for LCD Values Unit Parameter Min. Min. Type. Max.
Page 68
t 10 t 11 Note: (1) t4=0 : concern for residual pattern before BLU turn off. (2) t6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value) (3) When CMOS Interface signal is N.C. (no connection), opened it Transmitted end,t8 timing spec can be negligible.
Page 69
9. Backlight Specification 9-1 Electrical Characteristics None LED driver board 9-2 Input Pin Assignment LED Driver BD Output connector: CI0112M1HRL-NH(CviLux) or equivalent / Wire connector : CI 0112S0000 (Cvilux) Symbol Description Note VLED Anode of LED light bar (165 V , 0.32A ) Cathode of LED light bar 9-3 Power Sequence for Backlight None LED driver board...
11. Reliability Test Items Refer to 99.43S04.0AA 12. International Standard 12-1 Safety Refer to 99.43S04.0AA 12-2 EMC Refer to 99.43S04.0AA 13. Packing 10-1 Definition of Label A. Panel Label:...
Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) comment 1680x1050 65.29 59.9 146.25 VESA 1920x1080 67.5 148.5 Full HD Video Timing 720x480 15.73 13.5 DVI no support 720x576 15.625 13.5 DVI no support 720x480 31.469 SDTV 480P/60Hz 720x576 31.25 SDTV 576P/50Hz 1280x720 45.00 74.25 HDTV 720P/60Hz 1280x720...
Appendix 4 Shipping Troubleshooting Flowchart of System Trouble Shooting Power On OK? Check adapter AC socket to LCD TV. Check cable connection between power board and main board. Check power board VCC Backlight OK? Check cable connection between main board and Power Board (No full white) Check cable connection between Power board and LCD panel Check remote controller battery.
Page 79
OSD Image OK? Check cable connection between main board and LCD panel. No signal? Check input cable. Check OSD source set up. Audio OK? Check wire between Main board to speaker. Check audio input connection. Check main board Function OK? Flowchart of board trouble shooting Main board LED OK?