Related Manuals for Norden Mfg AF4
Summary of Contents for Norden Mfg AF4
- Page 1 Owner’s Manual AF4 Hay Accumulator Read and understand the manual. This manual provides information and MADE IN THE USA procedures to safely operate and maintain the Hay Accumulator.
-
Page 3: Table Of Contents
10.8 Belt and Tensioner ....41 10.9 Bale Chamber Extension ....42 AF4 Hay Accumulator Norden Mfg (877-296-5851) -
Page 4: Introduction
Record the serial number in the space provided for easy reference Please read the manual carefully to become when contacting Norden Mfg LLC with questions. familiar with your new Norden Hay Accumulator. This manual has been developed through our experience with the equipment and feedback from our customers. -
Page 5: Owner/Operator Manual Storage
1.7 Disposal of Equipment at End of Useful Life The Norden Mfg LLC Hay Accumulator has been designed for the specific purpose of arranging bales into groups. When this unit is no longer capable of performing its intended use, it should be dismantled and scrapped. -
Page 6: Safety
NOTICE Norden Mfg LLC cannot anticipate every Indicates that equipment or property damage can possible circumstance that might involve result if instructions are not followed. -
Page 7: Safety Icons Nomenclature
Defective or broken part Maintain safety signs Chock wheels Place in park Maintain safe distance Remove key Pinch point hazard Stop engine STOP Overturn hazard Visibility Negative tongue weight hazard Set parking brake Rollover hazard AF4 Hay Accumulator Norden Mfg (877-296-5851) -
Page 8: General Operating Safety
Do not allow riders on the tractor, If you do not understand any information in this or Hay Accumulator at any time. manual, see your dealer or contact Norden Mfg LLC Falling can result in severe injuries or death. before proceeding. -
Page 9: Sign-Off Form
2.8 Sign-Off Form Make periodic reviews of SAFETY and OPERATION of the Hay Accumulator a standard practice. An Norden Mfg LLC follows the general Safety untrained operator is not qualified to use this Hay Standards specified by the Farm Equipment Accumulator. -
Page 10: Operation Safety
2.12 Maintenance Safety Refer to “9. Maintenance” on page 32 for safety recommendations related to maintaining the Hay Accumulator. All applicable safety recommendations in other sections should also be followed. Norden Mfg (877-296-5851) AF4 Hay Accumulator... -
Page 11: Safety Signs And Labels
4. Replacement parts must have replacement labels attached before the Hay Accumulator is used. 5. Labels are available from your authorized dealer or from Norden Mfg LLC at no charge. 3.2 Contact Information AF4 Hay Accumulator Norden Mfg (877-296-5851) -
Page 12: Safety Sign Locations
3.4 Safety Sign Locations Item Type Description Qty. WARNING Read the Manual WARNING No Riders INFORMATIONAL Serial Number WARNING Pinch Point WARNING Do Not Transport at Speeds Over 20 MPH WARNING Fall Hazard Norden Mfg (877-296-5851) AF4 Hay Accumulator... -
Page 13: Hay Accumulator Safety Signs
WARNING FALLING HAZARD NO RIDERS Do not climb or stand on the unit at any time. KN-00047 Do not use the unit as a platform. Falling can result in serious injury or death. KN-00053 AF4 Hay Accumulator Norden Mfg (877-296-5851) -
Page 14: Nomenclature
Back Gate Belted Base Chute Back Gate Paddle Belt Tensioner Slow Moving Vehicle Sign Hitch Gate #1 Hexagon Plate Gate #2 Jack Gate #3 Reach Pole Gate Flipper Tires, ST225/75R15 Side Panels Accumulator Bed Norden Mfg (877-296-5851) AF4 Hay Accumulator... -
Page 15: Undercarriage
KN-00001 4.4 Belted Base Chute 4.2 Accumulator Bed The belted base chute is standard equipment on the The accumulator bed guides and positions the bales AF4 Hay Accumulator and will eliminate cornering on the accumulator. issues. KN-00002 KN-00004 AF4 Hay Accumulator... -
Page 16: Linkage System Operation
KN-00009 KN-00006 3. Bale #3 enters the Hay Accumulator and slides downward and into position, rotating the right gate to open row #4. KN-00007 Norden Mfg (877-296-5851) AF4 Hay Accumulator... -
Page 17: Assembly
5. Assembly 1. If the AF4 Hay Accumulator and EGF8 Grabber WARNING are palletized together for shipment. Begin Crush Hazard assembly by removing all components from the The accumulator bed weighs shipping pallet. approximately 600 pounds and can cause serious injury or death if it falls on a person. - Page 18 Do not fully tighten the bolts. KN-00014 Note: The reach poles can be inserted in either direction. KN-00016 Note: After the base chute bottom is attached, the accumulator will be heavy to the front, and will tip forward. Norden Mfg (877-296-5851) AF4 Hay Accumulator...
- Page 19 3/8 x 2-3/4” bolts and nuts. This part is not symmetrical and will only fit one way. Make sure the top surface of the hexagon is flush and parallel with the accumulator bed. Do not fully KN-00018 tighten the bolts. KN-00021 AF4 Hay Accumulator Norden Mfg (877-296-5851)
- Page 20 16. Attach the main chute using six 3/8 x 1” serrated flange bolts (1) and nuts at the bottom and two 3/8 x 1” carriage bolts (2) with serrated flange nuts at the top. Do not fully tighten the bolts. KN-00024 Norden Mfg (877-296-5851) AF4 Hay Accumulator...
- Page 21 5/8 x 6-1/2” bolts and nylon lock nuts. Set the hitch height to match the baler hitch height. Tighten the bolts to the proper torque. KN-00029 AF4 Hay Accumulator Norden Mfg (877-296-5851)
-
Page 22: Operation
Hay Accumulator. If the elderly are assisting with the work, their physical limitations need to be recognized and accommodated. Never allow children to operate equipment. Norden Mfg (877-296-5851) AF4 Hay Accumulator... -
Page 23: Equipment And Capabilities
Only operate the tractor with the ROPS in the raised position and seat belt fastened. AF4 Hay Accumulator Norden Mfg (877-296-5851) - Page 24 (not included) as spacers. Tighten the four carriage bolts on the sides of the chamber extension first, then the six flange bolts on the KN-00035 bottom. 8” - 10” KN-00076 Norden Mfg (877-296-5851) AF4 Hay Accumulator...
-
Page 25: Baler Chamber Settings
6.5 Baler Hitch Special Requirements 6.5.1 Older New Holland® (NH) Balers Older NH balers have the hitch on the right hand side of the chamber. Norden Mfg offers a center KN-00077 hitch adaptor to center the hitch. 10. Using the small end plate as a guide, drill three 7/16”... -
Page 26: John Deere® (Jd) Balers
The hitch on the JD baler may need to be modified equipment and clear of pinch points between the to meet the dimensions given in “6.3 Baler Hitch drawbar and accumulator hitch. Setup” on page 23. Norden Mfg offers a special hitch extension for John Deere® balers. WARNING Crush Hazard Crush hazard between hitch and implement. -
Page 27: Operation
Operate up and down (not across) intermediate slopes. Avoid sudden starts 6.8.1 Break In and stops. If problems persist, call Norden Mfg for service. To quickly and effectively “break in” the Hay Accumulator, apply silicone or cooking spray to the surface of the bed to make the bales slide easier. -
Page 28: Detaching From Baler
5. Detach the guide belt from the pins on the sides of the bale chamber. 6. Remove the drawbar pin from the clevis and drawbar. 7. Board the tractor and start the engine. Drive the tractor and baler away. Norden Mfg (877-296-5851) AF4 Hay Accumulator... -
Page 29: Transporting
This is particularly important with the chains under the tongue and secure to higher noise levels and quiet cabs, as you may the hitch. not hear people shouting. Do not allow anyone to ride on the unit. AF4 Hay Accumulator Norden Mfg (877-296-5851) -
Page 30: Highway And Transport Operations
• Watch for overhead obstructions and side clearances while transporting. • Always operate equipment in a position to provide maximum visibility at all times. Make allowances for increased length and weight of the equipment when making turns, stopping, etc. Norden Mfg (877-296-5851) AF4 Hay Accumulator... -
Page 31: Storage
28. 4. Lubricate all grease points. Make sure all grease cavities have been filled with grease to displace any trapped water from washing. 5. Touch up all paint nicks and scratches to prevent rusting. AF4 Hay Accumulator Norden Mfg (877-296-5851) -
Page 32: Maintenance
Unapproved parts could create a safety hazard. The manufacturer will not accept responsibility for damages as a result of the use of unapproved parts. Norden Mfg (877-296-5851) AF4 Hay Accumulator... -
Page 33: Lubrication
To adjust the wheel bearings, remove the dust cap and cotter pin. Lift the tire and slowly rotate it while tightening the spindle nut. Tighten only until a slight drag is felt on the rotating wheel. Re-install cotter pin and dust cap. AF4 Hay Accumulator Norden Mfg (877-296-5851) -
Page 34: Tire Safety
Use a torque wrench to Before performing any type of welding repair assure the proper amount of torque is being applied to the Hay Accumulator, contact Norden Mfg to the fastener. for approval. Repair welding must be done... -
Page 35: Service Record
Inspect the belted base chute and tensioner for wear and damage. Make sure the hitch, hitch bolts, and hitch pin are in good condition. Do not use homemade or shop made pins. Wash the accumulator. AF4 Hay Accumulator Norden Mfg (877-296-5851) -
Page 36: Parts Section
Remember, it is the users responsibility to maintain these decals. All decals must be in place and legible or all warranties are void. Norden Mfg (877-296-5851) AF4 Hay Accumulator... -
Page 37: Hay Accumulator Undercarriage
Combination of 7&8 (Tire and wheel) 1006080 Nut, Lock, Nylon, 5/16-18 1005160 Nut, Lug 1006140 Washer, Flat, 5/16” SAE 1004540 Jack 1004400 Mount, Jack * Refer to separate page for parts. 1006410 Bolt, Hex, 5/8 x 6-1/2” Grade 5 AF4 Hay Accumulator Norden Mfg (877-296-5851) -
Page 38: Hub Assembly
Washer 1006950 Nut, Hex, Slotted, 3/4-16 1003720 Pin, Cotter, 1/8 x 1-1/2” 1006970 Spindle 1006980 Dust Cap 1006990 Seal, Grease 1005160 Nut, Lug 1007000 Service Kit, Includes items 1, 2, 3, 4, 5, 1009460 Norden Mfg (877-296-5851) AF4 Hay Accumulator... -
Page 39: Accumulator Bed And Chute
Bolt, Hex, 1/4 x 3/4” Grade 5 1001900 Bracket, Dog, Hay 1006070 Nut, Lock, Nylon, 1/4-20 1004230 Panel, Side, Hexagon, Left 1006150 Washer, Flat, 3/8” SAE 1004240 Panel, Side, Hexagon, Right 1004220 Plate, Hexagon AF4 Hay Accumulator Norden Mfg (877-296-5851) -
Page 40: Linkage System
1003110 Bearing, Flange, Back Gate 1005180 Return Spring, Center Gate, 8” 1006080 Nut, Lock, Nylon, 5/16-18 1005170 Spring, Center Gate, 12” 1004310 Arm, 8” 1006450 Cable Assembly, Center Gate 1001020 Flipper, Gate 1000990 Gate Norden Mfg (877-296-5851) AF4 Hay Accumulator... -
Page 41: Belt And Tensioner
Belt End Plate, Large 1006770 Belt End Plate, Small 1003390 Saddle, Belt, Left 1006310 Bolt, Carriage, 3/8 x 1”, Grade 5 1003400 Saddle, Belt, Right 1006590 Spring, Belt Tensioner 1006400 Bolt, Hex, 5/8 x 1-1/2”, Grade 5 AF4 Hay Accumulator Norden Mfg (877-296-5851) -
Page 42: Bale Chamber Extension
Side, Chamber Extension, Left 1004440 Side, Chamber Extension, Right 1006320 Bolt, Carrriage, 3/8 x 1-1/4”, Grade 5 1006330 Bolt, Serrated Flange, 3/8 x 3/4”, Grade 5 1006190 Nut, Serrated Flange, 3/8-16, Grade 5 1006910 Pin, Cotter, Reuseable Norden Mfg (877-296-5851) AF4 Hay Accumulator... - Page 44 Norden Mfg LLC 4210 Kinsman Road NW North Bloomfield, OH 44450 www.Nordenmfg.com (877) 296-5851 support@Nordenmfg.com 1008400 Rev. C Revised 11-5-2021...