Page 1
Owner’s Manual WR8, WR10, WR12 Wheel Rakes Operator’s Manual for the WR-Series Wheel Rakes Read, Understand, and Follow the manual. This manual provides MADE IN THE USA information and procedures to safely operate and maintain the Wheel Rake.
By following the assembly, operating, and maintenance instructions in this manual, your Norden Mfg LLC wheel rake will provide many years of trouble-free service. 1.2 Description and Intended Use The wheel rake is designed to invert cut hay or...
OEM the serial number in the space provided for easy equipment manuals! The wheel rake, if not reference when contacting Norden Mfg LLC with assembled, used, and maintained properly, can questions. be dangerous to users unfamiliar with its operation.
1.10 Disposal of Equipment at End of Useful Life Store the Owner/Operator manual and other The Norden Mfg LLC wheel rake has been designed operating materials in the document storage tube for the specific purpose of raking hay and other located on the crossmember near the tongue.
Safety alert symbol procedure. Crushing hazard 2.3 Safety Icons Nomenclature This manual and the equipment have numerous safety symbols. These safety symbols indicate Crushing hazard important information about personal injury hazards. Falling hazard WR Series Wheel Rakes Norden Mfg (877-296-5851)
If the wheel rake has been altered in any way from the original design, Norden Mfg LLC does not In addition to this safety section, refer also to accept any liability for injury or warranty.
Hearing loss from loud noise is cumulative over a If you do not understand any information in this manual, see your dealer or contact Norden Mfg LLC lifetime without hope of natural recovery. before proceeding.
Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102). Norden Mfg (877-296-5851) WR Series Wheel Rakes...
Make periodic reviews of SAFETY and OPERATION follows the general Safety Standards of the wheel rake a standard practice. An untrained Norden Mfg LLC specified by the Farm Equipment Manufacturers operator is not qualified to use this wheel rake. Association (FEMA), the American National...
5. Replacement parts must have replacement labels attached during installation and/or before the wheel rake is used. 6. Labels are available from your authorized dealer or from Norden Mfg LLC at no charge. Norden Mfg (877-296-5851) WR Series Wheel Rakes...
4. Terminology Item Description Hitch Clevis Tongue Flotation Transport Wheel Right Lift Arm Right Rake Arm Left Rake Arm Headlands and Transport Lock Left Lift Arm WR Series Wheel Rakes Norden Mfg (877-296-5851)
Ratchet with extension and sockets as above 5.2 Assembly Procedure 1. Attached wheel to hub. Nuts in rake wheel should face the same direction as the nuts on the hub lugs. 2. Tighten all nuts (33 ft-lb) Norden Mfg (877-296-5851) WR Series Wheel Rakes...
12” above ground. See sticker for illustration. 5. For really tall drawbar heights, the hitch clevis can be inverted to gain extra height. b. Pull on the rope to unlock the safety latches Norden Mfg (877-296-5851) WR Series Wheel Rakes...
7. When finished, move the jack to its storage location on the wheel rake frame, and secure it 3. Pivot the rake arm to the desired position. WR Series Wheel Rakes Norden Mfg (877-296-5851)
Note: Using the hole 1 will result in the least upright/transport location while allowing the other amount of ground pressure. Using the side to move up and down as normal. hole 5 will give the most ground pressure. Norden Mfg (877-296-5851) WR Series Wheel Rakes...
Page 21
Because the Norden rake has an equalizer block, it is important that the arms are “in sync” when opening the valve again. WR Series Wheel Rakes Norden Mfg (877-296-5851)
If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury. 5. Remove the rope from the tractor and wrap around the provided bracket. 6. Remove the hitch pin. Norden Mfg (877-296-5851) WR Series Wheel Rakes...
When travelling below the posted speed folded. Use caution when transporting over limit, keep to the right and yield the uneven surfaces and slow down for turns. right-of-way to allow faster traffic to pass. WR Series Wheel Rakes Norden Mfg (877-296-5851)
Do not place hands or WARNING fingers between moving and/or stationary parts. The weight of the unit could easily cause serious bodily injury. After raising the wings, WARNING install both wing locks. Norden Mfg (877-296-5851) WR Series Wheel Rakes...
5. Lubricate all grease points. Make sure all grease cavities have been filled with grease to remove any remaining water from washing. 6. Touch up all paint nicks and scratches to prevent rusting. WR Series Wheel Rakes Norden Mfg (877-296-5851)
Unapproved parts could create a safety hazard. immediately by a doctor familiar with this type of The manufacturer will not accept responsibility injury. for damages as a result of the use of unapproved parts. Norden Mfg (877-296-5851) WR Series Wheel Rakes...
Before performing any type of welding repair are provided to help prevent INSTRUCTIONS injury or limit equipment damage. to the wheel rake, contact Norden Mfg LLC for approval. Repair welding must be done Safety Equipment with care and with procedures that may be beyond A fire extinguisher and first aid kit the capabilities of the ordinary welder.
7. Check tightness of lug bolts after one hour of operation and every six months thereafter. Check tire pressure whenever maintenance is performed. 3. Lubricate the rake wheel hubs every 15 hours of operation. Norden Mfg (877-296-5851) WR Series Wheel Rakes...
Excessive speed on rough ground. Reduce speed. Narrow or deep ditches or furrows, Avoid or cross at a slow speed. rocky ground. Too much ground pressure. Decrease the ground pressure. Refer to “6.3.4 Adjust the Rake Wheel Ground Pressure”. Norden Mfg (877-296-5851) WR Series Wheel Rakes...
Contact Information For replacement decals, questions, or to order parts, contact: Norden Mfg LLC 4210 Kinsmann Rd. NW North Bloomfield, OH 44450 Phone: 877-296-5851 Fax: 440-693-4336 E-mail: service@nordenmfg.com...
Tongue View 11.15 Kicker Wheel View 11.16 Hydraulics View 11.17 Hub Assembly 11.18 Lift Arm and Flotation View 11.19 Left Arm WR8 11.20 Right Arm WR8 11.21 Left Arm WR10 11.22 RIght Arm WR10 11.23 Left Arm WR12 11.24 RIght Arm WR12 11.25...
Item Part Number Description Qty. 1014860 2x10 Hydraulic Cylinder 1014980 4MJ-6MB90 Adapter 1014900 Main Hose, short 1014920 Lift Cylinder Hose 1014910 Main Hose, long Rake Manifold Assembly, 1013930 Section 11.14 1015840 Male Pioneer End WR Series Wheel Rakes Norden Mfg (877-296-5851)
11.20 Left Arm WR8 View Item Part Number Description Qty. Item Part Number Description Qty. 1013690 Lift Arm Insert Left 1013790 Pivot Pin Washer 1013711 Rake Arm Left 1006280 5/16-18 x 0.75 Hex Bolt Grade 5 1013050 Tandem Rake Tube, Left 1016520 1/2-13 x 3.25 Hex Bolt Grade 5...
11.21 Right Arm WR8 View Item Part Number Description Qty. Item Part Number Description Qty. 1013700 Lift Arm Insert Right 1013790 Pivot Pin Washer 1013721 Rake Arm Right 1013750 Rake Arm Pivot Pin 1013060 Tandem Rake Tube, Right 1013820 Angle Lock Pin 1016520 1/2-13 x 3.25 Hex Bolt Grade 5...