Casio TI-310 Owner's Manual

IMPORTANT
SAFETY INSTRUCTIONS
I
INSTALLATION INSTRUCTIONS
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the
network interface.
4. Use caution when installing or modifying telephone lines.
SAFETY PRECAUTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
4. Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage
to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by
placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near
or over a radiator or heat register. This product should not be placed in an enclosed environment unless
proper ventilation is provided.
7. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by
animals or persons walking on it.
8. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the
product.
10.To reduce the risk of electric shock, do not disassemble this product. Take it to a qualified serviceperson when
service or repair work is required. Opening or removing covers may expose you to dangerous voltages or
other risks. Incorrect re-assembly can cause electric shock when the appliance is subsequently used.
11.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operating instructions because improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to restore the product to normal
operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
12.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of
electric shock from lightning.
13.Do not use the telephone to report a gas leak while near the leak.
SAVE THESE INSTRUCTIONS
FCC REQUIREMENTS
USER INSTRUCTIONS
L
1. This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment is a label
that contains, among other information, the FCC registration number and Ringer Equivalence
Number (REN) for this equipment. If requested, provide this information to your telephone company.
2. The REN is useful to determine the quantity of devices you may connect to your telephone line and
still have all of those devices ring when your number is called. In most, but not all areas, the sum of
the RENs of all devices should not exceed five (5.0). To be certain of the number of devices you may
connect to your line, as determined by the REN, you should call your local telephone company to
determine the maximum REN for your calling area.
3. If your answering machine causes harm to the telephone network, the telephone company may
discontinue your service temporarily. If possible, they will notify you in advance. But if advance
notice is not practical, you will be notified as soon as possible. You will be advised of your right to
file a complaint with the FCC.
4. Your telephone company may make changes in its facilities, equipment, operations, or procedures
that could affect the proper operation of your equipment. If they do, you will be given advance notice
so as to give you an opportunity to maintain uninterrupted service.
5. If there is a problem with this unit, the telephone company may ask you to disconnect this
equipment from the network until the problem has been corrected or you are sure that the
equipment is not malfunctioning.
6. Repairs can only be made by the manufacturer or an authorized service agency. Unauthorized
repairs void registration and warranty. Contact seller or manufacturer for details of permissible user-
performed routine repairs, and where and how to have other than routine repairs made.
7. This equipment may not be used on coin service provided by the telephone company. Connection to
party lines is subject to state tariffs. (Contact your state public utility commission or corporation
commission for information.)
Jack: RJ11 Ringer Equivalence: See bottom/underside of the TI-310 base unit.
CASIO COMMUNICATIONS, Inc. 20665 Manhattan Place, Torrance, CA 90501
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes made by the user not approved by CASIO COMMUNICATIONS can void the user's
authority to operate the equipment. This product is hearing aid compatible.
REMOTE OPERATION
Remote operation allows you to access the TI-310
CHANGE YOUR
from any cellular or touch-tone phone. The 3-digit
Remote Access Code is printed on the bottom of
GREETING
the unit. To enable remote operation, you may
need to press and hold each remote access
(OPTION 3)
number for 2 seconds. If you intend to call from
rotary or pulse telephones, order the Touchtone
1
If your TI-310 is currently playing back
Dialer on the ACCESSORY page.
1
messages, press on your keypad to
pause playback.
LISTENING TO
2 3
Press on your telephone keypad, a
MESSAGES
beep will be heard, begin recording your
(OPTION 1) new greeting.
1 3
Press 3 on your telephone keypad when
After the access code has been entered,
finished speaking. Your new greeting
messages will automatically be played.
will play automatically.
NOTE:
PAUSING MESSAGES
There is a one minute maximum for recording your
greeting through remote operation.
1
During playback of the message you want
SKIP BACKWARD
1
paused, press on your keypad.
Messages will be paused for up to one
(OPTION 4)
minute before disconnecting. To resume
1
playback, press again.
1
4
Press on your keypad to skip back to
the previous message.
ERASE MESSAGES
REPEAT MESSAGE
(OPTION 2)
(OPTION 5)
1 During playback of the message you want
2
erased, press on your touchtone keypad. 1
5
Press on your keypad to repeat the
To confirm deletion of the message, you
current message.
will hear a beep.
SKIP FORWARD
2 To erase all messages, press 2 after
hearing " End of Messages. " You will
hear a beep and all messages will be (OPTION 6)
erased.
1 6
Press on you keypad to skip forward
to the next message.
REFERENCIA RÁPIDA
M
CONEXIÓN DEL TI-310 GRABACIÓN DE
MENSAJES DE SALIDA
1 ENCHUFE el cordón de teléfono del
Grabe un mensaje de salida personalizado de
TI-310 en un enchufe de pared de
hasta 1 minuto de duración para responder a las
teléfono.
llamadas.
Asegúrese de que los indicadores
1
CONECTE
2 el enchufe del adaptador
luminosos están encendidos o
de CA en el tomacorriente para
destellando. El mensaje de salida debe
adaptador de CA que hay en la parte
ser de más de dos segundos o la unidad
ENGANCHE
de atrás del TI-310. el
utilizará el mensaje de salida
cordón a través del sujetador de
predeterminado.
cordón del adaptador de CA para
evitar una desconexión accidental. 2
(VOLUME)
Fije el control de volumen
NOTA:
en un nivel que usted pueda oír.
La desconexión del adaptador de CA de
la parte de atrás de la unidad hará que la
NOTA:
TI-310 borre todos los mensajes
El nivel de sonido se ajusta automáticamente cuando el
recibidos, mensajes de salida, números
mensaje de salida se transmite por la línea de teléfono.
de marcación automática, hora y fecha.
3
Oprima el botón de grabación de
(GREETING
mensaje de salida
ENCHUFE
3 el cordón extensible del
RECORD)
y espere que se encienda el
auricular en el auricular y en el lado
indicador de grabación (RECORD
izquierdo del TI-310.
INDICATOR) . Oirá una señal acústica.
NOTA:
4
ENCHUFE
el adaptador de CA en un Si la memoria del TI-310 está llena, reproduzca y
tomacorriente de pared eléctrico. borre todos los mensajes antes de grabar su
mensaje de salida
Después de la señal acústica, los
indicadores luminosos destellarán.
4
Comience a hablar a aproximadamente
Una vez que los indicadores
7 plg del micrófono.
luminosos comiencen a destellar, se
puede grabar un mensaje de salida.
5
Cuando termine de hablar, oprima el
botón de grabación de mensaje de
INSTALE
5 una batería de 9 voltios
(GREETING RECORD)
salida
(9V) para proteger los mensajes de
nuevamente para dejar de grabar. Si no
salida, los mensajes recibidos y las
oprime el botón de grabación de
configuraciones de hora y día.
(GREETING
mensaje de salida
Durante un corte de suministro
RECORD)
, la unidad dejará
eléctrico, esta información se guarda
automáticamente de grabar pasado un
hasta que la batería se agote.
minuto.
6
La TI-310 reproducirá automáticamente
el mensaje de salida.

TROUBLESHOOTING

J
REMOTE ANSWER
Recorded messages are cut off.
OFF/ON The TI-310 is designed to disconnect from the
line after a caller stops talking. Calls may be cut
(OPTION 7 & 8) off if a 5 second pause is detected, if the caller
does not speak loud enough or if a message is
1 8
Press on your keypad after hearing less than two seconds.
" End of messages ." to turn the
answering machine off. Upon exiting
The TI-310 does not respond when you enter
remote operation, the unit will be turned
your remote access code while the greeting is
off and no further messages will be
playing
recorded.
Try re-entering the correct code after the beep.
Press each number of the access code for at
2
In the event you accidentally turned your
least two seconds.
7
answering machine off, press on your
keypad to turn the unit back on.
Between messages there is an operator
recording or a beep and dial tone.
EXITING REMOTE
The caller has hung up without leaving a
message. A shorter greeting will reduce the
OPERATION
frequency of these recordings.
(OPTION 9)
You have more than one telephone number
1 9 and are experiencing difficulty.
Press on your keypad at any time
See MULTI-LINE INSTALLATION.
during remote operation to exit.
There is no sound during playback.
MESSAGE RETRIEVAL
Check and adjust the VOLUME .
WHEN MEMORY
The unit does not automatically stop playing
IS FULL
the greeting or recording a message when an
extension phone is picked up.
If the TI-310's memory is full, you will hear three
Briefly press and release the HOOK-SWITCH on
short beeps followed by, " Memory full. " To retrieve
the extension phone.
messages remotely when the TI-310's memory is
full:
The unit is not responding when keys are
1
3-DIGIT ACCESS CODE pressed.
Enter your
The TI-310 has approximately a 5 second
as the greeting plays.
initialization process. Once the unit is plugged
in, the unit requires 5 seconds in which it runs
2 its internal diagnostic tests. The MESSAGES
After listening to messages, you may
2 INDICATOR will flash when the unit is ready for
press on the keypad to erase all
operation.
messages and allow callers to leave new
messages.

WALL MOUNTING

N
The TI-310 can easily be wall mounted by following these instructions. If you have a standard
telephone wall mounting bracket, begin with step 2.
NOTE:
Purchase wood screws, round head, brass, size #10, 1 1/4 inches in length.
1 Mount screws into wall. Use the
template (right) to space screws
T
correctly.
E
2 Guide the telephone cord through the
right cord holder on the unit's
M
bottom.
Tightly coil the telephone cord
3 P
around the four guides on the in-side
of the wall mounting bracket.
L
4
Pull the telephone cord through the
A
center opening on the wall mounting
bracket.
T
5
Guide the AC Adapter through the left
cord holder on the bottom of the
E
unit.
6 Tightly coil the AC Adapter cord
around the four guides on the in-
side of the wall mounting bracket.
7 Direct the AC Adapter cord through
the opening in the side of the wall
mounting bracket.
8
Snap the wall mounting bracket into
the back of the TI-310.
9
Plug the AC Adapter into a wall outlet
and the telephone cord into a wall
jack.
10 Remove the handset retainer clip
located above the speaker grill in
the handset cradle and rotate the
clip 180 degrees. Replace the
clip. This secures the handset.
K
After recording a new greeting from remote QUESTIONS?
operation, the unit does not respond.
HERE'S HOW TO REACH US
After you record your new greeting, you must
press 3 again on your keypad to end the
By Phone:
recording. If 3 is not pressed, the unit will
suspend remote operation access for 13 HELPLINE: (310) 320-9810, Monday - Friday,
minutes. You will be able to retrieve your 8 a.m. to 4:45 p.m., PST
messages after the 13 minutes. AUTHORIZED FACTORY SERVICE CENTER:
Phone Masters Repair Center
(714) 373-4233, Monday - Friday,
A greeting was recorded but the default
8 a.m. to 5 p.m., PST
greeting plays.
PARTS ORDERS USING A CREDIT CARD:
Check the length of the recorded greeting. In
Pacific Coast Parts Distributors, Inc.
order for the TI-310 to accept a greeting, it must
(800) 421-5080 or (310) 515-0207,
be at least two seconds in length or the unit will
Monday - Friday, 8 a.m. to 4:30 p.m., PST
default to the pre-recorded greeting.
On-line:
After several attempts the TI-310 will not
CUSTOMER RELATIONS:
operate properly.
WEBSITE: www.casiocomm.com
E-MAIL: cpmicust@casio.com
To reset the TI-310, unplug the AC ADAPTER
PLUG from the back of the TI-310 for 10 AUTHORIZED FACTORY SERVICE CENTER:
seconds and remove the battery (if one is WEBSITE: www.members.home.net/
installed). The greeting, incoming messages skelly1/PM1.htm
and time/day stamp will be lost. Re-record the E-MAIL: phonemasters@hotmail.com
greetings and set the time and day. PARTS AND ACCESSORIES:
WEBSITE: www.pacparts.com
E-MAIL: orders@pacparts.com
AUTHORIZED FACTORY SERVICE CENTER
For repairs, please bring or send your unit to:
Phone Masters Repair Center
11899 Valley View Street
Garden Grove, CA 92845
1. Pack your product securely in a sturdy
shipping box.
2. Include a clear and specific explanation of
Design and specifications are subject to
change without notice. the problem.
3. Include your name, street address (sorry,
CASIO COMMUNICATIONS, INC.
no P.O. box), and daytime phone number.
20665 Manhattan Place
4. Provide a legible photocopy of the dated
Torrance, CA 90501-1827
store receipt for one-year warranty
Internet Website: purposes.
http://www.casiocomm.com
Register on-line at www.casiocomm.com
M2S1 3/00 or fill-out and return the enclosed
product registration card.
Printed in Malaysia

LIMITED WARRANTY

O
IMPORTANT! SALES SLIP OR EVIDENCE OF PURCHASE DATE REQUIRED
This limited warranty gives you specific legal rights; you may also have other rights which vary from state to state.
The limited warranty is extended only to the original consumer of a CASIO COMMUNICATIONS product and is valid
only with respect to consumers within the United States of America and Canada. Should this product prove defective by
reason of improper workmanship or material during the period of one (1) year from the date of original purchase,
CASIO COMMUNICATIONS will repair or, at its option, replace the product without charge for parts or labor. If CASIO
COMMUNICATIONS elects to replace the product, such replacement may be accomplished with a factory-reconditioned
unit. This limited warranty does not apply: (a) to any product damaged by accident, misuse, improper line voltage,
lightning, fire, water, or other acts of nature, (b) if the product is altered or repaired by anyone other than CASIO
COMMUNICATIONS, INC. or one of its authorized warranty stations or (c) if the FCC-approved connector plugs are
removed. This limited warranty does not cover broken or marred cabinets.
Except to the extent prohibited by applicable law, all implied warranties made by CASIO COMMUNICATIONS in
connection with this product are limited in duration to a period of one (1) year from the date of original purchase, and
no warranties, whether expressed or implied, shall apply to this product after said period.
Should this product prove defective in workmanship or material, the consumer's sole remedies shall be such repair or
replacement as is herein-above provided. Under no circumstances shall CASIO COMMUNICATIONS be liable for any
loss or damage, direct, consequential, or incidental arising out of the use of or inability to use this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusion may not apply to you.
In order to obtain warranty service, you must provide evidence of purchase date. For your convenience, keep the
dealer's dated bill of sale or delivery ticket as evidence of the purchase date. See Troubleshooting section above for
details. Before returning or exchanging your product, call the CASIO COMMUNICATIONS Helpline at (310) 320-9810.
ACCESSORIES
P
To order accessories for your TI-310, simply cut out this order form, fill in the appropriate information
and send it with payment (check, money order or credit card information) to:
Pacific Coast Parts Distributors, Inc., 15024 Staff Court, Gardena, CA 90248. For parts orders using a
credit card: (800) 421-5080 or (310) 515-0207, Monday - Friday, 8 a.m. to 4:30 p.m., PST.
To order on-line: www.pacparts.com E-MAIL: orders@pacparts.com
Description Part No. Price Qty. Total
Lightning Arrestor - Recommended for areas prone to electrical storms. 2700140 $19.95
AC Adapter 1601086 $13.50
- For Model TI-310.
Touchtone Dialer - Activates the beeperless remote operation. 2001018 $19.95
Enclosed is my check/money order for the total amount. Subtotal
CA residents add applicable sales tax
Please charge my credit card.
VISA MasterCard
All orders add shipping and handling $3.50
Total
Card No. Expiration Date
Name ______________________________________________________________________________
Street Address _______________________________________________________________________
City _________________________________________ State __________ Zip Code _______________
Signature ___________________________________________ Telephone _______________________
We do not accept C.O.D. orders. Allow 15 working days for delivery. Prices subject to change without
notice. Returns subject to 20% restocking charge upon approval.
4336-920-0-01
EASY TO USE
OWNER'S GUIDE
TI-310
Telephone with
Digital Answering Machine
Turn over for
installation
instructions
INSTALLATION
A
Install a 9 volt (9V) battery to protect your greeting, incoming messages and time/day setting during
power failure. During a power failure, this information is saved until the battery is depleted.
1
Turn the TI-310 over and remove the battery cover. Install a 9V alkaline battery. Make sure the
battery is connected correctly. Replace the cover.
2
PLUG
the TI-310's telephone cord
into a telephone wall jack.
USE ONLY WITH ADAPTOR
MODEL M/N-75
3
CONNECT
the AC Adapter Plug into the AC Adapter Outlet on
LOOP
the back of the TI-310. the cord through the AC Adapter
Cord Holder to prevent accidental disconnection.
NOTE:
Disconnection of the AC Adapter from the back of the unit will cause the TI-310
to erase all recorded messages, greetings, autodial numbers, the time and
date.
4
PLUG
the coiled handset cord into the
handset and into the left side of the TI-310.
5 PLUG
the AC Adapter into an electrical wall
outlet. After the beep the LEDs will flash.
Once the LEDs start flashing, you may record
your greeting.