Protecting The Environment; Troubleshooting; Maintenance - Black & Decker BDCDD12USB Manual

pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
Hold the drill firmly with two hands to control its twisting
u
action.
DO NOT CLICK THE TRIGGER OF A STALLED DRILL
u
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
Minimize stalling on breakthrough by reducing pressure
u
and slowly drilling through the last part of the hole.
Keep the motor running while pulling the bit out of a drilled
u
hole. This will help reduce jamming.
Make sure switch turns drill on and off.
u
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
from the flutes.
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulfurized cutting oil or lard oil.
Screwdriving
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
u
amount of washing liquid or soap as a lubricant.
Always hold the tool and screwdriver bit in a straight line
u
with the screw

Troubleshooting

Problem Possible cause
Unit will not start. Battery pack not
charged.
Battery pack will not Charger not plugged
charge. in.
Surrounding air
temperature too hot or
too cold.
Unit shuts off Battery pack has
abruptly. reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted

Maintenance

Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
@
regular cleaning.
Š Regularly clean the ventilation slots in your tool and
Š Regularly clean the motor housing using a damp cloth.

Protecting the environment

Z
Products and batteries contain materials that can be recov-
ered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according to
local provisions.
Further information is available at www.2helpU.com
Technical data
Possible solution
Check battery pack charg-
ing requirements
Plug charger into a work-
ing outlet.
Move charger and battery
Charger
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Allow battery pack to cool
down.
Place on charger
and allow to charge.
(Original instructions)
Warning! Before performing any maintenance on the
tool, remove the battery from the tool. Unplug the
charger before cleaning it.
charger using a soft brush or dry cloth.
Do not use any abrasive or solvent-based cleaner.
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Voltage V
DC
No-load speed Min
Max. torque Nm
Chuck capacity mm
Max Drilling capacity
Steel/wood mm
Weight kg
Battery (Not Supplied)
Voltage
V dc
Capacity
Ah
Type
Input voltage V
AC
Output voltage V
DC
Output current A
Approx. charge time Hours
Level of sound pressure according to EN 62841:
Sound pressure (L ) 62.8 dB(A), uncertainty (K) 5 dB(A)
pA
Sound power (L ) 73.8 dB(A), uncertainty (K) 5 dB(A)
WA
Vibration total values (triax vector sum) according to EN 62841:
Drilling into metal (a ) <2.5 m/s , uncertainty (K) 1.5 m/s
2
h, D
ENGLISH
BDCDD12USB
0 - 550 RPM
-1
12.5 / 26
1 - 10
10 / 25
0.79 (with battery 1.04)
BDCB12
Lithium-Ion
100-240V
2
12
12
1.5
5V
1
1.5
7