Download Print this page

Advertisement

Owner's Manual
Network Set-up and Operation
For Windows
Wired and Wireless Setting
Projector Set-up and Operation
Network Capture
Network Viewer
Moderator Function
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic operation of the
projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.

Advertisement

   Related Manuals for Sanyo PLCXL51

   Summary of Contents for Sanyo PLCXL51

  • Page 1: For Windows

    This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed strictly.

  • Page 2: Compliance

    20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles). : QXXAVC922---P : Sanyo : SANYO FISHER COMPANY : 21605 Plummer Street, Chatsworth, California 91311 : (818)998-7322...

  • Page 3

    övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. [Swedish] Islenska Hér með lýsir SANYO Electric Co., Ltd. yfir því að (QXXAVC922---P) er í samræmi við grunnkröfur og [Icelandic] aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC. Norsk SANYO Electric Co., Ltd.

  • Page 4: Safety Instructions

    Incorrect installation may cause fire or other accidents. CAUTION IN USING NETWORK FUNCTION ● SANYO Electric Co., Ltd. assumes no responsibility for the loss or damage of data, or damage of the computer caused by using this projector. Making back-up copies of valuable data in your computer is recommended.

  • Page 5: Table Of Contents

    Safety instructions ...4 Table of contents ...5 Operating environment and configuration ...7 Required operating environment for computers ...7 Network specifications of the projector ...8 1. About LAN functions ...9 LAN functions and the features ...10 Image projecting system via LAN ...10 An example of the connection ...11...

  • Page 6

    Initial setting ...48 Network configuration ...51 Configuring wireless LAN setting and security setting...53 E-mail setting ...55 SNMP setting ...59 7. Controlling the projector ...63 Power control and status check ...64 Controls ...66 PC adjustment ...70 Setting up the projector ...71 Timer setting ...74...

  • Page 7: Operating Environment And Configuration

    Operating environment and configuration Required operating environment for computers When operating the projector via the networks, computers should meet the operating environment below. Memory Free HDD Space Screen Resolution Communication Protocol Wireless LAN Network Correspond Wired LAN Browser Application Microsoft Windows 2000 or...

  • Page 8: Network Specifications Of The Projector

    Network specifications of the projector LAN Terminal Data communication speed Protocol Wireless LAN Interface Communication Mode Data Transfer Speed Wireless Frequency (Channel) Modulation Form Protocol Security Service area Compliance Countries and Standards 100Base-TX (100Mbps)/10Base-T (10Mbps) TCP/IP IEEE802.11b/g AdHoc, Infrastructure 1/2/5.5/11Mbps (IEEE802.11b) 6/9/12/18/24/36/48/54Mbps (IEEE802.11g)

  • Page 9: About Lan Functions

    1. About LAN functions This chapter describes the features, the mechanism, and connection procedures of the LAN. Chapter...

  • Page 10: Lan Functions And The Features

    1. Download the computer image with the dedicated software faithfully to the real image. 2. The downloaded data will be compressed to the digital signal and transferred to the projector via the LAN (Wired or Wireless). (One computer can operate up to 5 projectors simultaneously.) 3.

  • Page 11: An Example Of The Connection

    An example of the connection The illustration below shows an example of the projection via the LAN. You can project the image on Computer (1) (Wired LAN connection), or Computer (2) (Wireless LAN connection) through the selected projector . Computer (1) Access point...

  • Page 12: Lan Connection Modes

    Computer (1) Wireless LAN, AdHoc Communication Mode ■ Communication mode between Wireless LAN equipment. (Communication mode via SSID/ESSID) Computer (2) Access point Network Projector Wireless communication mode :AdHoc Wireless communication mode corresponded computer: AdHoc Wireless communication mode corresponded computer: Infrastructure...

  • Page 13

    When the projector’s remote control employs mouse operating function, you can operate the computer by the remote control. To use the remote control, point to the projector. You do not need to connect the USB cable to operate the computer mouse.

  • Page 14

    Chapter 1 About LAN functions...

  • Page 15: Setup Procedures

    2. Setup procedures This chapter describes how to install the Network Capture 5 software and how to set up the networks. Chapter...

  • Page 16

    Chapter 2 Setup procedures To use the projector via the networks, follow the setup procedures below. Install the software on computers. STEP 1 Install the software recorded in CD-ROM on each computer which will be operated. Read following pages of this chapter to install.

  • Page 17: Installing The Software

    Installing the software It is required to install the software into your computer to use the Network Capture function . Please install the software as follows. Note: To install the software into the computer with Windows 2000, Windows XP or Windows Vista, you should logon as administrator.

  • Page 18

    Chapter 2 Setup procedures As the "License Agreement" will appear, read contents carefully and click Yes button if you agree to the license agreement to proceed with installing. During the installation, following window may appear, click Continue Anyway button. Click Finish to complete the installation.

  • Page 19: Installed Software

    Installed software The following 3 softwares are installed on your computer. Network Capture 5: ● Captures the displayed image and the sound of the computer and serves them to the projector via the network. Network Viewer 5 (File Converter 1): ●...

  • Page 20: File Converter 2 Installation

    ● Network Viewer 5 (File Converter 2): This is a kind of the printer driver to convert to the JPEG data optimized to project by the projector from any of the documents created by the application software. * To uninstall Network Viewer 5 (File Converter 2), just delete the "Network Viewer 5(File Converter 2)" icon from the "Printers and faxes"...

  • Page 21: Names And Functions Of The Operation Screen

    3. Names and functions of the operation screen This chapter describes the functions of each part of the operation screen. Chapter...

  • Page 22: Network Connection Standby Display

    Chapter 3 Names and functions of the operating screen Network connection standby display Turn on the projector and select either “Wired” or “Wireless” from the input menu of the projector. The “Please wait... ” message will be displayed on the screen. After short time, the network connection standby display screen will appear as below.

  • Page 23: Network Capture 5 Window

    In that case, press this button, the "Search specified IP address list" window appears, and then click Add button and enter the IP address directly to specify the projector in another window. The registered multiple IP addresses can be searched at a time.

  • Page 24

    Moderator registration button Register a computer user as a moderator. !0 Join moderator's group button Join the moderator's group which is selected in the Network Projector list. It is not available if there is no moderator registered. !1 Parameter setup button Activate the parameter setup window, and execute the connections setting, the image setting, and the moderator's function setting.

  • Page 25: Wired Lan Configurations

    4. Wired LAN configurations This chapter describes the preparation for Wired LAN setting with projectors and how to set the LAN environment. Chapter...

  • Page 26: Connecting To The Lan Line

    1. Turn on the projector and select “Wired” from the input menu of the projector. The projector’s LINK/ACT Lamp will be on or blink. If the “Wired setting” is “Off”, it will not be on. Follow step 2 and 3 to blink the lamp.

  • Page 27

    DHCP ... Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When it set On, IP address, Subnet, Gateway and DNS are automatically set according to your network environment * IP address ...Sets IP address of the projector Subnet ...Sets Subnet mask. Normally sets 255.255.255.0 Gateway* ...Sets IP address of the default gateway (Router)

  • Page 28: Confirming The Operation

    Firewall function and try searching again. ✳ If the projector is named, the name will be displayed. The name can be set with the following procedures in “6. Basic setting and operation” ➔ “Initial setting” (p48) . If the projector is not named, IP address of the projector will be displayed.

  • Page 29

    1. Press Specify IP button. "Search specified IP address" window appears. 2. Click Add button, "IP address set up" window appears. Enter the IP address of the projector and Click OK button. Then, the projector will be added on the "Search specified IP address" window. Multiple projectors are registered and they are stored even when the application is closed.

  • Page 30: Network Pin Code

    When you do not want to set the Network PIN code, set It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. See “6. Basic setting and operation” ➔ “Initial setting” ➔...

  • Page 31: Wired Lan Factory Default Settings

    Wired LAN factory default settings Parameter IP ADDRESS SUBNET MASK GATEWAY ADDRESS DNS ADDRESS IP CONFIGURATION SELECTED LAN LAN1 LAN2 169.254.100.100 192.168.100.100 255.255.0.0 255.255.255.0 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 MANUAL DHCP Wired LAN factory default settings LAN3 192.168.100.100 255.255.255.0 255.255.255.255 255.255.255.255 MANUAL...

  • Page 32

    Chapter 4 Wired LAN configurations...

  • Page 33: Wireless Lan Configurations

    This chapter describes the preparation for Wireless LAN setting with projectors and how to set the LAN environment. This projector contains the Wireless LAN module. The setting procedures and configurations differ depending on the LAN installation location. Consult your system administrator for installation and set the LAN appropriately.

  • Page 34: Setting The Network Environment

    With Easy wireless setting function, you can make Wireless LAN settings easily without any complicating settings (p.39). 1. Turn on the projector and select “Wireless” from the input menu of the projector. The “Please wait... ” message will be displayed on the screen. After short time, the network connection standby display screen will appear.

  • Page 35

    SSID/ESSID for the network type “Infrastructure” and “AdHoc” are required to be entered the same characters into the projector, the access point, and the Wireless LAN compatible computer (up to 32 characters). Characters can be selected from A~Z, a~z, blank (space), 0–9, or - (hyphen) with the Point ed buttons.

  • Page 36: Configuring Security With The Projector

    Use the Point ed buttons to select the security type. To disable the security, select “Disable. ” Use the Point 7 8 buttons to move among the items; use the Point ed buttons to adjust settings. This projector provides the following security options. Use optimum security option on your network environment.

  • Page 37: Use Of Security Type "wep

    4. Use the Point 7 8 buttons to select “Set” and press SELECT button to return to the Wireless setting screen. Select “Set” in the Wireless setting screen to complete the network setting. Characters 5 characters 10 characters 13 characters 26 characters Configuring security with the projector...

  • Page 38

    * Security "WPA-PSK" and "WPA2-PSK" modes are not available when the "AdHoc" network type is selected. * When you set the PSK keys with 64 digits, the projector checks whether all of the entered PSK keys are in Hex code or...

  • Page 39: Easy Wireless Setting

    After completing the settings, the computer will start searching the projector which was set as “SIMPLE” and will display the name of the projector or the IP address on the projector list. Confirm whether the LAN has been set correctly and works properly. Refer to “4. Wired LAN configurations”...

  • Page 40: Network Pin Code

    The Network PIN code is to restrict the access from the networks to the projector. After setting the Network PIN code, you need to enter it to operate the projector via the networks. Select “Network PIN code” from the projector menu and press SELECT button. Set with the same procedures as setting Wired LAN Network PIN code.

  • Page 41: Wireless Indicator Display

    When the wireless LAN configuration is set up correctly and the wireless communication is established with the access-point or the computer in the network, the WIRELESS indicator on the side panel lights up. While the projector scans the equipment in the network, the WIRELESS indicator blinks. WIRELESS indicator...

  • Page 42: Wireless Lan Factory Default Settings

    Chapter 5 Wireless LAN configurations Wireless LAN factory default settings Factory default settings for LAN4, LAN5, and SIMPLE as follows. Setting Items IP ADDRESS SUBNETMASK GATEWAY ADDRESS DNS ADDRESS IP CONFIGURATION WIRELESS CHANNEL NETWORK TYPE WIRELESS SSID/ESSID (SSID/ESSID) (WEP encryption) WPA-PSK (PSK key) WPA2-PSK...

  • Page 43: Basic Setting And Operation

    Configure E-mail function to manage the projector. • SNMP Setting Configure SNMP function to manage the projector. Caution: When operating the projector with the browser, connect the projector to the computer with Wired or Wireless LAN. Complete the connection in advance. Chapter...

  • Page 44: Starting Up The Browser

    2. Start up the Network Capture 5. The Network Capture 5 searches projectors in the network and lists up the IP address or projector name of the projector on the Network Projector List. 3. Double click the projector to set from the Network Projector List.

  • Page 45: Display Of Main Setting Page

    Main setting page in the Standard Mode display Main menu For selection of control and setting items of the projector. * To change the screen language, use the initial setting menu (p.48) This Standard mode display is mainly used through this manual for the setting and ✐...

  • Page 46: How To Use The Setting Page

    ✐ Each item has a valid setting range. The setting value exceeding its range becomes invalid. Some control items can not be used depending on the selected input mode or functions of the projector you use. In that case, the values of those items are indicated with "---".

  • Page 47

    Type of the setting pallet Text box setting Enter the number or text and then click Set button. C h a n g e a v a l u e w i t h s o r t button and then click Set button. The value changes quickly when s or t button is kept pressing.

  • Page 48: Initial Setting

    Japanese. Model name ... Indicates the model name of the projector. Projector name ... Sets the name of projector. This projector name is listed on the application window of the Network Capture software. Network PIN code ... Sets the Network PIN code to login the setting page (+p.30, p.40)

  • Page 49: Network Pin Code Setting

    The default Network PIN code as [0000], which means no Network PIN code is set. ✐ When you connect the projector to the network, it is recommended to set a new Network PIN code. Only a four- digit number is valid for the Network PIN code.

  • Page 50: Date And Time Setting

    After setting the NTP address, the projector acquires the time per 24 hours. If the projector fails acquiring the time from the NTP server, the projector tries to acquire the time every 1 hour until it succeeds.

  • Page 51: Network Configuration

    Network configuration Click Network on the main menu. The following setting page is displayed. Set up the projector's network environment on this Setting sub menu. Setting of LAN 1. Select a type of LAN from Change setting pull down menu.

  • Page 52

    4. To apply the setting, press Set button. The network of the projector starts re-booting and applies the setting. It takes about 20 seconds to complete. Close the web browser and access to the login page again in 20 seconds.

  • Page 53: Configuring Wireless Lan Setting And Security Setting

    SSID/ESSID is case-sensitive. Even though all characters on the Wireless information is uppercase, it is necessary to distinguish between upper case and lower case characters. Channel ...I f you use the projector in 802.11AdHoc mode, select the channel, from 1 to 11. Configuring wireless LAN setting and security setting...

  • Page 54

    Chapter 6 Basic setting and operation Configuring wireless LAN security setting Click page [3] of setting pages. Following wireless LAN security setting can be done. After completing the configuration, press Set button. Item Description Network security ...Sets the type of encryption. Following types are available. WEP64(40)bit Open WEP64(40)bit Share WEP128(104)bit Open...

  • Page 55: E-mail Setting

    ✐ If the projector sends an alert message due to the abnormality on the projector but the SMTP server is down in some other reason, the message will not be sent. In that case, the message "Unable to connect to server." will be displayed on the setting page.

  • Page 56

    "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control.

  • Page 57

    P-FAIL MAIN, 1.8V MCI, P-FAIL ✐ The projector lamp was turned off, because the projector power circuit failed. Unplug the projector from AC outlet and contact a qualified service personnel for service with the error information. Error information E-mail setting...

  • Page 58

    *The PJ lamp replace time is reached. ✐ Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users in every power-on of the projector. This alert mail will not be sent when the mail sending condition "When the life span of lamp is reached"...

  • Page 59: Snmp Setting

    Refer (read only) and Set (read- write). This product allows to use Refer (read only) only. The SNMP message informs the projector status called "Trap" to an administrator. Click SNMP Setting on the main menu and set up each item.

  • Page 60

    Chapter 6 Basic setting and operation Trap Item Description Community name ... Enter community name to send "Trap". Default name is "public". Trap address ... Enter IP address of the SNMP manager computer to receive "Trap". Up to 10 address can be registered. ✐...

  • Page 61

    ✐ "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/ STANDBY button on the top control or the remote control.

  • Page 62

    Chapter 6 Basic setting and operation...

  • Page 63: Controlling The Projector

    7. Controlling the projector Describes controlling and setting of the projector by using the web browser. Chapter...

  • Page 64: Power Control And Status Check

    Chapter 7 Controlling the projector Power control and status check Click Power & Status on the main menu. The control page will be displayed. By clicking ON or Standby button on the page, the power of the projector can be controlled. Item...

  • Page 65

    If you set this function as Normal, the network part of the projector is constantly provided with power even if the projector is turned off. If you set this as Eco, then the network part will be turned off when you turn off the projector. Consequently, you cannot turn on/off the projector via the networks.

  • Page 66: Controls

    For further information , refer to the projector's owner's manual. ✐ When the projector is standby, only the timer on the setting menu is available; others are not available. Item Description Input ...

  • Page 67

    System This function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu button according to the input signal. Select a system and then click Set button. ✐ If the modes (Mode1 to Mode5) stored in the item "PC Adjustment" (+ p.70) are available, they are also listed together with the above mode.

  • Page 68: Image Adjustment

    Chapter 7 Controlling the projector Image adjustment This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and to load the adjusted value, click Load button. Input source...

  • Page 69

    Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status. Item Description Volume ... Adjusts the sound volume from the speakers. Mute ... Suppresses the sound.

  • Page 70: Pc Adjustment

    Chapter 7 Controlling the projector PC adjustment Click PC Adj. on the main menu. This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode ... Displays a current mode like VGA, SVGA, XGA, SXGA, UXGA, WXGA, etc.

  • Page 71: Setting Up The Projector

    Setting up the projector Click Setting on the main menu. This function is to set up the projector. Select the sub menu [Screen setting], [Setting 1] or , [Setting 2] and then set up each setting. Item Screen ... Switches the screen mode. There may not be available ✐...

  • Page 72

    Chapter 7 Controlling the projector Item Description Language ... Sets the language display of projector's on-screen display menu. Auto setup ... Executes the Auto PC Adj, and Input Search function below according to the each setting after clicking button. Auto PC Adj..Sets Auto PC Adjustment mode.

  • Page 73

    Filter warning ... Sets the time to indicate the filter warning message on the screen. Item Description Factory default ... Sets all of the projector control items to the factory default setting except the following items. Lamp Corres. Value, PJ time, Filter time, PIN code lock and Logo PIN code lock.

  • Page 74: Timer Setting

    Chapter 7 Controlling the projector Timer setting This page is to set the timer to turn the projector off or on at a programmed day/date and time. Follow the steps below for setting. Click Timer on the main menu. "---" will appear on the cur- rent time when the time is not set up correctly.

  • Page 75: Check The Timer Events

    Select an event action Select an event action from the pull-down menu. Event Action ON ... Turns on the projector OFF ... Turns off the projector Lamp Auto ... Changes lamp mode to "Auto" Lamp Normal ... Changes lamp mode to "Normal"...

  • Page 76

    5, event 6 OFF will not be effective in turning it off again. But these secondary events (event 4 and event 6) will become effective if a person turns off the projector (after event 3 and before event 4) or turns on the projector (after event 5 and before event 6).

  • Page 77: Projector Information

    Projector information This page is to display the basic information of the projector status. Click Information on the main menu. Items Input ...Displays selected input and source. System ...Displays selected signal system. Signal ...Input signal status Screen ...Displays screen mode.

  • Page 78

    Lamp failure (Lamp failure and lamp is being used over a specified use time, replace the lamp immediately) Items Description PJ time ... Displays the accumulated use time of the projector. Lamp Corres. Value ... Displays the use time (Corresponding value) of the lamp.

  • Page 79: Multi-control

    When you install multiple projectors in the network, you can control and set up them together. Click Multi Control on the main menu to display the control page. Note: To control the multiple projectors, each projector must be set the same Network PIN code. Example of multi control Multi-control Select Input2 for PJ1 to PJ4.

  • Page 80: Start/stop The Multi Control

    Chapter 7 Controlling the projector Start/stop the multi control To start or stop controlling the multi-projectors, click Multi control setting menu and select ON or OFF. Multi control setting OFF ...Stops multi control function ON ... Starts multi control function. The multi control menu will appear when ON is set.

  • Page 81: Register The Projector

    Register the projector To use the multi control function, register the IP address of the projector you intend to control. Click Pj registration sub menu tab and set the IP address, Memo and Multi control item, then click Set button.

  • Page 82: Change The Mode Of The Registered Projector

    ✐ Cannot register, delete or change the multi-control setting during using the network viewer function. ✐ It is recommended that a specified projector should be chosen for setting as a master when you use this multi- control function. The control for the multi-controlled projectors will become too complicated operation if this function is used for each projector.

  • Page 83: Controlling All Together

    The setting value is applied to the registered projectors sequentially . ✐ This is effective only if the multi control item of the registered projector is set to either "Control & Image" or "Control". Setting all together "E-mail setting", "SNMP setting"...

  • Page 84: Viewer Auto Setting All Together

    ✐ For further information of the Auto display, see "Using the network viewer function". (+p.120) ✐ This is effective only if the multi control item of the registered projector is set to either "Control & Image" or "Image".

  • Page 85: Network Capture Functions

    8. Network capture functions Network Capture is a function to display the screen image and reproduce the sound of the computer via the network. - Real Time Capture - Network Communication - Moderator Function Chapter...

  • Page 86: About Network Capture Function

    - Network Communication (+p.94) This mode is to communicate by sharing the capture image of a computer with multiple computers and a projector. User can draw the text and figure on the captured image by using a drawing tool. - Moderator Function (+p.103) The moderator can project the participants’...

  • Page 87: Commands On The Task Bar

    One-shot capture ... Transfers the one-shot screen image of the computer. Capture transfer ... Transfers the screen image of the computer to the projector. The captured image edit window appears on the computer screen.

  • Page 88: Parameter Set Up

    Capture port ... Sets the capture port no. on the projector. Default is 9000. Pincode ... Sets the Network PIN code on the projector. PJ search time ... Sets the time to search the projector between 1 to 60 seconds. Default is 5 seconds. q Select normal network adapter Uses default setting.

  • Page 89: Using The Real Time Capture

    IP address for each page. ✐ When you capture the screen image of the movie player software with the real time capture function, the projector may not be able to reproduce the sound. To reproduce the sound in the projector correctly, follow the procedures below;...

  • Page 90: Control By The Computer

    ✐ If the error message appears, check the item "Parameter set up" (+ p.88). ✐ The sound output from the projector can be controlled with the volume slider and mute item on the application window of the Network Capture 5 software (+ p.24, p.86).

  • Page 91: Control By The Web Browser

    ✐ The IP address of the connecting PC should be registered previously (+ p.89). ✐ If the error message appears, check item "Parameter set up" (+ p.88). ✐ To use the capture function from the web browser or projector, the Network Capture 5 on the captured computer must be activated.

  • Page 92

    ✐ If the error message appears, check item "Parameter set up" (+ p.88). ✐ The projector does not provide the function to register the IP address of the computer and to set the parameter of the capturing. They should be registered by using the web browser previously (+ p.89-90).

  • Page 93: Control By The Computer With Usb Memory

    USB thumb drive by drag and drop. 2. Turn on the projector and select “Wireless” from the input menu of the projector. 3. Select “Wireless Setting” from the projector menu and press SELECT button. Select “SIMPLE” with the Point 7 8 buttons.

  • Page 94: Using The Network Communication

    Using the Network Communication This Network Communication is to communicate by sharing the captured image of a computer with multiple computers and a projector. Users can draw the text and figure on the captured image by using a drawing tool.

  • Page 95: Settings Before Using The Network Communication

    Settings before using the Network Communication To use the Network Communication, the capture setting of the projector must be set either [1] or [2] as described below. [1] Projector searches all the available subject computers in the network automatically. [2] Subject computers are registered to the projector.

  • Page 96: Description Of Capture Editing Window

    Chapter 8 Network capture functions Description of capture editing window Start Network Capture 5 and select the projector(s) on the projector list on the application window and click Communication Start button. The application window will disappear and the capture editing window will appear on the computer screen as below.

  • Page 97

    Tool bar button names The following commands are assigned to the tool bar buttons. For each operation, refer to the description of the item "Menu tree". Command Tool Save Bar of Main PC communication Capture Authority transfer Standard tool bar Form tool bar Pencil...

  • Page 98: How To Use The Network Communication

    Start Network Capture 5. The application window appears and the projectors in the network are listed. Select the projector(s) and click Start Communication button. The application window disappears and the capture editing window with a captured image appears on the computer screen. The projector displays captured image on the screen.

  • Page 99: Edit Capture Image

    Edit capture image Drawing figures Click " :Pencil" button on the form tool bar. Select its attribute (shape, width, color and translucence) from the form and attribute tool bar. Drag a mouse pointer on the screen image to draw the figure. Erase drawn objects Click "...

  • Page 100

    Chapter 8 Network capture functions Drawing letter Click " :Letter frame" button on the form tool bar. Select a color of text with color tool bar. Drag a mouse pointer on the screen image to specify the area of the letter frame. The letter input dialog window will appear.

  • Page 101: Network Communication Operation And Change Of State

    , Ending the communication. ➔ The capture editing window disappears. ✐ The projector projects the edited captured image on the screen when the input mode of the projector is set "Network". ✐ The command "Save Communication" can be executed in any of the mode even if the PC does not have the authority.

  • Page 102: Executing The Forcing Mode

    Chapter 8 Network capture functions Executing the forcing mode The network capture setting of the web page provides a forcing executing command. This command executes the release of authority or ending the communication forcibly. This is useful when the other subject PC keeps an authority all the time, or when the condition of the communication is not stable.

  • Page 103: Moderator Function

    This function enables you to project the participants’ data directly in a short time and in real time without taking time to transfer the data to the computer connected to the projector. The image data will not be limited by the computer’s application because the data transfer of each computer adopts the screen capturing system.

  • Page 104: Preparation For Using The Moderator Function

    Following application window appears when the Network Capture starts. After clicking Moderator registration button, the application window changes to "Moderator mode" window as shown in the lower picture below. Normal mode application window Projector list Status of use M o d e r a t o r registration...

  • Page 105: Using The Moderator Function

    Moderator registration ...Register a moderator's group Delete moderator group ...Quit a moderator's group Join moderator's group .. Join a moderator's group. Press this button after selecting the projector which is indicated with "In Moderator mode" on the status column. Start real time capture .. Capture (Project) the computer screen in real time. After the execution of "Start real time capture", and the application window disappears.

  • Page 106: Moderator's Password Setting Up

    The input password is registered in the moderator's password of the client. Unregister moderator status 1. Select the projector(s) which is registered as a moderator from the moderator mode application window. 2. Click the Delete moderator's group button. Selected projector will be unregistered on a moderator, and the application window changes "Normal mode".

  • Page 107: Error Information

    Start real time capture or Terminate capture. ➔ Check connection of the network cable. Cannot transfer the data to the projector when the Start Communication, Terminate Communication, Capture transfer, Start real time capture or Terminate capture is executed. The time-out period is 10 seconds.

  • Page 108

    Chapter 8 Network capture functions...

  • Page 109: Network Viewer Functions

    9. Network Viewer functions Network Viewer is a function to display the image data stored in the file servers by the projector through the network. Describes the file converter software File Converter 1, File Converter 2, the program creator software Program Editor, and how to use Network Viewer.

  • Page 110: Creating The Available Data [network Viewer 5]

    Creating the available data [Network Viewer 5] The image available with this projector is the JPEG format (.jpg). There are several types of JPEG data. Some data may not be projected. Before using the images with the Network Viewer function, it should be converted to the optimized JPEG data for this projector.

  • Page 111: Menu Tree

    Menu Tree Menu Sub Menu View Update Preview size Tools Option Conversion Convert each file Convert a folder Help Version information Command Tool Button Convert Convert a each file folder Creating the available data Select a folder in which the image files are stored by the explorer window. The preview images of the available image data (JPEG file, Bitmap file, power point file) in the selected folder are displayed on the preview window.

  • Page 112

    Chapter 9 Network Viewer functions When converting each file, select a preview image first and then click Convert each file. ✐ To select two or more files at once, press and hold "Shift" key or "Ctrl" key and then click the preview images. When converting all the files in a folder, select a folder and click Convert a folder.

  • Page 113

    Output folder ... Specify a directory of the FTP server. Conversion mode Resolution ... Selects output image resolution (VGA to SXGA+) ✐ The image resolution higher than the projector's panel resolution cannot be displayed. Image rotation ... Selects image rotation (0, 90, 180, 270). Conversion Type Fit ...

  • Page 114

    Chapter 9 Network Viewer functions [2] How to use the Network Viewer 5 (File Converter 2) The File Converter 2 is a kind of the printer driver software to convert to the optimized JPEG data for the projection from the any documents created by the other software such as text editor, spreadsheet or presentation software.

  • Page 115: Creating A Program File [program Editor]

    "DispParam" at the login root directory in the FTP server, and files with each program name into this folder. These files are called "Program". By specifying the program file with the Network Viewer function, you can display the images in programmed order with the projector . Procedure of making program To start up the Program Editor, click "Network Viewer 5 (Program...

  • Page 116

    Chapter 9 Network Viewer functions Click New button. Enter a program name and click Add button. The folder selection window appears and select a folder in which the JPEG data are stored and then click Add button to register into the folder lists. Add ...Displays the folder selection window.

  • Page 117: Setting Up The Display Order And Time Of The Images

    Setting up the display order and time of the images In the default setting, the display order of the images is the same as ASCII code order of the file name. To change the display order or to set up the display time, take the following procedures. Display the folder list window in step 6 of the previous page.

  • Page 118

    Chapter 9 Network Viewer functions To change the display order, select* move them onto your desired place, or select files and then drag and drop them onto your desired place with mouse. To change the display time* click Display time button on the menu bar to display the Display time setting window.

  • Page 119

    Example of the created program selection Use the web browser to access to the control page of the projector. Click "Viewer" of the Network menu on the web page, then connect to the FTP server and select the program name which was made at previous section.

  • Page 120: Using The Network Viewer Function

    [1] Control by the web browser FTP file server Select "Network" for input mode previously. Access to the control page on the projector by using the web browser. From the main menu, click Network - Viewer to display the setting page. JPEG...

  • Page 121

    Setup the setting page [1] of the Visual display. Item Description Host name ... Enter the host name or IP address of FTP server, yourftp.server etc. Folder Path ... Use "/"(root directory) normally, or enter the directory name follow the "/" as shown in the below example if you have a specified directory in the server.

  • Page 122

    Chapter 9 Network Viewer functions After clicking Set, the file list or preview list of the selected folder or program is displayed on the window. The original image is displayed on another window by clicking on the preview image or file name ✐...

  • Page 123

    Error info. 1. Click Start button to start the auto-display. The image in the selected folder or program is displayed on the projector's screen. The web browser opens another window and displays the preview images on the Auto Control window sequentially.

  • Page 124

    JPEG FTP file server Select "Network" input mode previously. Select "Network Viewer" icon from "Network" menu. Press SELECT button on the projector twice to display the network viewer setting pallet. Description It is displayed when the projector cannot acquire the correct file images from the FTP server, or when the master projector is turned off during the multi-control.

  • Page 125

    ✐ The image data used for this function is the program or folder that the Network Viewer function used last time. The projector cannot specify particular images or file servers itself. ✐ The display time is greatly affected by the network environment or the operation of multi control, so the image display may not be displayed as it is set for the specified display time.

  • Page 126

    Chapter 9 Network Viewer functions...

  • Page 127: Appendix

    10. Appendix Use of telnet Web browser setting Firewall setting Troubleshooting Terminology Chapter...

  • Page 128: Use Of Telnet

    You can control the projector by using the telnet application the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of the Windows XP Professional.) 1.

  • Page 129

    4. Type the commands, refer to below table, to control the projector and then press "Enter" key for termination. For example, type "C00" which is a command to turn on the projector, and press "Enter" key. Confirm the projector is turning on.

  • Page 130: Web Browser Setting

    Chapter 10 Appendix Web browser setting This product is designed to enable the projector to be set up and controlled from an Internet web browser. Depending on the preference settings of the web browser, some control functions may not be available.

  • Page 131: Windows Xp Professional

    Examples: OS/Browsers Windows XP Professional Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level… button. On the security setting window, scroll down and find the Scripting item, make sure that "Enable"...

  • Page 132: Proxy Setting

    - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with UTP cross cable, it must be unchecked. To designate proxy settings that will not use the proxy server when accessing the projector installed in the local area network, enter the IP address or domain name here.

  • Page 133

    Netscape Navigator v.7.0 JavaScript Setting S e l e c t P r e f e r e n c e f r o m E d i t menu on the web browser and then select the item Advanced/ Scripts &...

  • Page 134

    Select the item Direct connection to the Internet If you connect the projector to the computer directly with UTP cross cable, this must be selected. To designate prox y settings that will not use the proxy server when accessing the projector installed in the local area network, enter the IP address or domain name here.

  • Page 135: Firewall Setting

    Firewall setting If you use Windows XP SP2 or Windows Vista and using Network Capture 5, you may see the Windows security warning dialog as below. In that case, click "Cancel the block" button on the dialog to enable the function of Network Capture 5. (This page is described with Windows XP screen the example.) Even if you select "Block", you can cancel the blocking following to the steps below;...

  • Page 136: Troubleshooting

    Chapter 10 Appendix Troubleshooting If you have any trouble in setup or operation of the projector, refer to the troubleshooting items and check the relevant matters described. ■ The computer cannot connect projectors. Wired LAN Is the LAN cable connected to the projector properly?

  • Page 137

    ■ Connection between computer and the projector via Wired LAN cannot be established. When selecting LAN1 (factory default setting) Check IP address, Sub net and Gateway of the projector and computer. For further details of the configuration, contact your system administrator.

  • Page 138: Network Capture

    2. Check the parameter set up (+p.88). Make sure that the numbers of the capture port is the same as the projector’s port number. The default port number is 9000. If the alert message "Invalid Port No." appears, your computer may be using this port number already.

  • Page 139

    If the computer using the same channel as yours is existing closely, the networking speed may be reduced or the communication unstable. Change the channel to resolve the problem. The channels of the projector and projector Client computer must be the same. Or adjust the Quality selection in the parameter setting.

  • Page 140: Network Viewer

    4. There are several limitations for image file name and program name. Please check file names and program names (+p.119). 5. Make sure that your computer is not using the firewall function. The projector may not be able to use the port due to this firewall function. In that case, please turn off this function temporarily.

  • Page 141

    Troubleshooting ■ Sometime I have the incorrect images converted by the File Converter 2? Try to change the mode to "Disable" on "Document options" - "Print optimization" item on the "Network Viewer 5 (Driver) Advance Options" in the Network Viewer 5 (FileConverter 2) Printer driver setting.

  • Page 142: Terminology

    Chapter 10 Appendix Terminology DHCP server (Dynamic Host Configuration Protocol) It is necessary to set an IP address for each computer or equivalent equipment when a network is established by TCP/IP. If there exists DHCP server on the network, it will assign IP addresses to client computers every time they request it.

  • Page 143

    Terminology...

  • Page 144

    SO-WIN-KV7A SANYO Electric Co., Ltd. NETWORK OWNER'S MANUAL FOR WINDOWS...

This manual also for:

Plc-xl51 - 2700 lumens

Comments to this Manuals

Symbols: 0
Latest comments: