Download Print this page

Advertisement

BASIC SERIAL COMMAND SPECIFICATIONS
PLC-XL51
Ver.1.00
SANYO Electric Co., Ltd
DS Company
Projector Division

Advertisement

   Also See for Sanyo PLC-XL51 - 2700 Lumens

   Related Manuals for Sanyo PLC-XL51 - 2700 Lumens

   Summary of Contents for Sanyo PLC-XL51 - 2700 Lumens

  • Page 1

    BASIC SERIAL COMMAND SPECIFICATIONS PLC-XL51 Ver.1.00 SANYO Electric Co., Ltd DS Company Projector Division...

  • Page 2: Table Of Contents

    PLC-XL51 Basic Serial Command Specifications ÿ CONTENTS ÿ Overview .........................5 Serial Interface Specifications ..................5 2.1. Transfer Specifications ..................5 2.2. Connection ......................5 Notes for Communication .....................6 Functional Execution Command Table ................7 Status Read Command Table ..................8 Functional Execution Command ..................9 6.1. Format ........................9 6.2.

  • Page 3

    PLC-XL51 Basic Serial Command Specifications 6.32. BRIGHTNESS – Command .................. 15 6.33. IMAGE (Toggle) Command.................. 15 6.34. ON START Setting Command ................16 6.35. ON START Cancel Command ................16 6.36. Power Management Ready Command .............. 16 6.37. Power Management OFF Command ..............16 6.38.

  • Page 4

    PLC-XL51 Basic Serial Command Specifications 7.8. Lamp Mode Read Command ................25 4/25...

  • Page 5: Overview

    PLC-XL51 Basic Serial Command Specifications 1. Overview 1.1. These specifications define projector control commands for PLC-XL51. 1.2. The projector control commands are used to remotely control a projector through RS-232C from a computer. 2. Serial Interface Specifications 2.1. Transfer Specifications Item Specifications Synchronous system...

  • Page 6: Notes For Communication

    PLC-XL51 Basic Serial Command Specifications Notes for Communication The projector control command is defined as one command/one line that starts with “C” and ends with carriage return (0x0D). There are two types of Commands: Functional Execution Commands and Status Read Commands.

  • Page 7: Functional Execution Command Table

    PLC-XL51 Basic Serial Command Specifications Functional Execution Command Table Command Item Command Item POWER ON BRIGHTNESS + POWER OFF BRIGHTNESS - ÿ Quick Power OFFÿ ――― POWER OFF ――― ――― ――― ――― ――― Computer 1 ――― Computer 2 IMAGE ÿ Toggleÿ Video ―――...

  • Page 8: Status Read Command Table

    PLC-XL51 Basic Serial Command Specifications Command Item Command Item ――― Reset ――― Input WIRED Cancel Input WIRELESS ――― FREEZE ON ――― FREEZE OFF ――― ――― ――― ZOOM - ――― ZOOM + ――― ――― ――― Auto PC ADJ. ――― PRESENTATION TIMER ―――...

  • Page 9: Functional Execution Command

    PLC-XL51 Basic Serial Command Specifications Functional Execution Command 6.1. Format 6.1.1 PC issues a command in format as below. “C” COMMAND [CR] Command: two characters (See Basic Functional Execution Command Table) A projector changes received data to decode and returns a result after being ready to receive next command.

  • Page 10: Operation Requirements

    PLC-XL51 Basic Serial Command Specifications 6.4. Operation Requirements When the projector’s status is any of below, Functional Execution Commands are limited. Projector Status Available Functional Execution Commands Standby Mode C00ÿ POWER ON C00ÿ POWER ON → Countdown is terminated Countdown in process C01ÿ...

  • Page 11: Power On Command

    PLC-XL51 Basic Serial Command Specifications 6.5. POWER ON Command Command “C00” [CR] Power ON When already Power is ON, nothing is done. Detail When sending this command during processing Countdown, Countdown is terminated. Acceptable [ACK] [CR] Response Unacceptable “ÿ ”[CR] 6.6.

  • Page 12: Video Command

    PLC-XL51 Basic Serial Command Specifications 6.10. Video Command Command “C07” [CR] Select Video Input Detail Input search is not executed by receiving this command even it is set to On1/On2. Acceptable [ACK] [CR] Response Unacceptable “ÿ ”[CR] 6.11. VOLUME + Command Command “C09”...

  • Page 13: Video Mute On Command

    PLC-XL51 Basic Serial Command Specifications 6.15. VIDEO MUTE ON Command Command “C0D”[CR] Video Mute ON. Detail This command works the same way as “NO SHOW” button of the remote control for No Show ON, but does not work for No Show OFF. Acceptable [ACK] [CR] Response...

  • Page 14: Image Cinema Command

    PLC-XL51 Basic Serial Command Specifications 6.21. Image Cinema Command Command “C13” [CR] Detail Set image to Cinema mode. Acceptable [ACK] [CR] Response Unacceptable “ÿ ”[CR] 6.22. Image1 Command Command “C14” [CR] Detail Set image to Image1 mode. Acceptable [ACK] [CR] Response Unacceptable “ÿ...

  • Page 15: Menu On Command

    PLC-XL51 Basic Serial Command Specifications 6.28. MENU ON Command Command “C1C” [CR] Detail Display On-Screen Display Menu. Acceptable [ACK] [CR] Response Unacceptable “ÿ ”[CR] 6.29. MENU OFF Command Command “C1D” [CR] Detail Hide On-Screen Display Menu. Acceptable [ACK] [CR] Response Unacceptable “ÿ...

  • Page 16: On Start Setting Command

    PLC-XL51 Basic Serial Command Specifications 6.34. ON START Setting Command Command “C28” [CR] Enable Power ON Start. Detail This status is stored in EEPROM and retained regardless of Power OFF/ON. Acceptable [ACK] [CR] Response Unacceptable “ÿ ”[CR] 6.35. ON START Cancel Command Command “C29”...

  • Page 17: D.zoom - Command

    PLC-XL51 Basic Serial Command Specifications 6.40. D.ZOOM – Command Command “C31” [CR] Enter Digital Zoom mode and reduce image size. Detail This command works the same as “D.ZOOM ▼” button of the remote control. Acceptable [ACK] [CR] Response Unacceptable “ÿ ”[CR] 6.41.

  • Page 18: Pointer Right Command

    PLC-XL51 Basic Serial Command Specifications 6.46. POINTER RIGHT Command Command “C3A” [CR] Move the Pointer of On-Screen Display Menu to the right. Detail This command works differently from the pointer “>” of the projector and remote control, and has no function of Volume +. Acceptable [ACK] [CR] Response...

  • Page 19: Freeze On Command

    PLC-XL51 Basic Serial Command Specifications 6.52. FREEZE ON Command Command “C43” [CR] Freeze on-screen image. Detail This command works the same way as “FREEZE” button of the remote control for Freeze ON, but does not work for Freeze OFF. Acceptable [ACK] [CR] Response Unacceptable...

  • Page 20: Input Wired Command

    PLC-XL51 Basic Serial Command Specifications 6.58. INPUT WIRED Command Command “C81” [CR] Detail Select Wired LAN signal. Acceptable [ACK] [CR] Response Unacceptable “ÿ ”[CR] 6.59. INPUT WIRELESS Command Command “C82” [CR] Detail Select Wireless LAN signal Acceptable [ACK] [CR] Response Unacceptable “ÿ...

  • Page 21: Status Read Command

    PLC-XL51 Basic Serial Command Specifications 7. Status Read Command 7.1. Format 7.1.1. PC issues commands in format as below; “CR” Command [CR] Commandÿ 1 characterÿ See Basic Status Read Command Tableÿ 7.1.2. When a projector receives the appropriate command, it returns a character line as the required data.

  • Page 22

    PLC-XL51 Basic Serial Command Specifications [Details of Response] 7.3.1. “00” [CR] Status : Power ON Normal image is on the screen. 7.3.2. “80” [CR] Status: Standby When the status is Standby, Status Read Commands are always acceptable, but Functional Execution Commands are not acceptable except POWER ON Command. 7.3.3.

  • Page 23

    PLC-XL51 Basic Serial Command Specifications information of temperature anomaly is canceled and normal operation is executed. 7.3.8. “24”[CR] Status: Processing Power Save / Cooling Down Power management function in Setting menu works and the status goes to Power Save / Cooling Down. During this time, Functional Execution Commands are invalid (not executed).

  • Page 24: Input Mode Read Command

    PLC-XL51 Basic Serial Command Specifications 7.4. Input Mode Read Command Command “CR1” [CR] Detail Get the selected Input No. Acceptable “%1” [CR] ”1” = Computer 1 is selected ”2” = Computer 2 is selected Response “3” = Video is selected “4”...

  • Page 25

    PLC-XL51 Basic Serial Command Specifications 7.8. Lamp Mode Read Command Command “CR7” [CR] Get lamp mode status. Detail For 1 lamp projector, get if it is lighting or not. Acceptable “%1” [CR] “00” [CR]=Light is out. Response “01” [CR]=Light is on. Unacceptable “ÿ...

Comments to this Manuals

Symbols: 0
Latest comments: