Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec BF06WP
Summary of Contents for Trotec BF06WP
- Page 1 BF06WP OPERATING MANUAL LUXMETER...
-
Page 2: Table Of Contents
• Remove the batteries from the device if you will not be using the device for a longer period of time. • Never short-circuit the supply terminal in the battery compartment! luxmeter BF06WP... - Page 3 Observe and comply with the technical data. Warning of electrical voltage The Trotec MultiMeasure Mobile app on the terminal device is There is a risk of a short-circuit due to liquids used for both operation and the evaluation of the measured penetrating the housing! values.
-
Page 4: Information About The Device
Information about the device Measuring sensor Device description On / off / measurement button Used in combination with Trotec's MultiMeasure Mobile app the Battery compartment with cover luxmeter permits the measurement of illuminances. Lock In case of individual measurements, the measurement value... -
Page 5: Transport And Storage
Storage When the device is not being used, observe the following Install the Trotec MultiMeasure Mobile app on the terminal storage conditions: device you want to use in combination with the device. • dry and protected from frost and heat Info •... - Page 6 ü The Trotec MultiMeasure Mobile app is installed. measurement. ü The Bluetooth function on your terminal device is activated. 1. Start the Trotec MultiMeasure Mobile app on the terminal When the appSensor has been successfully connected to the device. terminal device, a continuous measurement is started and 2.
- Page 7 ð The appSensor determines the current measured value which is then displayed on the terminal device. 2. You can also press the On / off / measurement button (3) on the appSensor. ð The appSensor determines the current measured value which is then displayed on the terminal device. luxmeter BF06WP...
- Page 8 Proceed as follows to stop recording the measured values: 1. Press the REC button (20). ð The context menu for sensors opens. 2. Press the Stop recording button (21). ð The context menu for saving the recording opens. 3. You can optionally save, discard or resume the measurement. luxmeter BF06WP...
- Page 9 Evaluation parameters. They will not be added to the already saved measurement, to be sure, but if you save the measurement again with a different name, these parameters will be added to the initial measurement. luxmeter BF06WP...
- Page 10 Sensors Measurements Reports Customers Settings Reports 03/26/2019 Sensors Measurements Reports Customers Settings Customers report 01 report 02 Test customer_A1 Test customer_A2 No. Designation Meaning 37 Display reports Opens the selected report. button luxmeter BF06WP...
- Page 11 Proceed as follows to adjust the settings for the appSensor: ð The appSensor is switched off. 1. Press the Sensors button (6). 2. You may now exit the Trotec MultiMeasure Mobile app on ð A list of connected and available sensors will be the terminal device.
-
Page 12: Errors And Faults
(see chapter Technical that apply for many EU countries on the website data) or are there any solid building parts (walls, pillars https://hub.trotec.com/?id=45090. Otherwise, please contact an etc.) situated between appSensor and terminal device? official recycling centre for electronic and electrical equipment Shorten the distance between the two devices and ensure authorised for your country. -
Page 13: Declaration Of Conformity
Declaration of conformity We – Trotec GmbH – declare in sole responsibility that the product designated below was developed, constructed and produced in compliance with the requirements of the EU Radio Equipment Directive in the version 2014/53/EU. Product model/Product: BF06WP luxmeter Product type:... - Page 14 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...