How To Use Advanced Functions - Carrier RG10A2/BGEF Owner's Manual

4. HOW TO USE ADVANCED FUNCTIONS

Press Swing button when the unit is turned on.
The horizontal louver will
Swing
swing up and down automatically
when pressing Swing button.
Swing
Press again to make it stop.
If continue to press the SWING button, five different airflow directions can be set(Model dependent). The louver can
be move at a certain range each time you press the button. Press the button until the direction you prefer is reached.
Press this button under COOL Mode to enter the energy efficient mode.
Press this button to enter the energy efficient mode in a sequence of
following:
ECO GEAR(75%)
Note:This function is only available under COOL mode.
ECO operation:
Eco
Under cooling mode, press this button, the remote controller will adjust the temperature automatically to
24 C/75 F, fan speed of Auto to save energy (only when the set temperature is less than 24 C/75 F). If the O O
Gear
set temperature is above 24 C/75 F, press this button, the fan speed will change to Auto, the set temperature
O
will remain unchanged.
Note:
Pressing the this button, or modifying the mode or adjusting the set temperature to less than 24 C/75 F will
stop ECO operation.
Under ECO operation, the set tmeperature should be 24 C/75 F or above, it may result in
insufficient cooling. If you feel uncomfortable, just press this button again to stop it.
GEAR operation:
Press the Eco/Gear button to enter the GEAR operation as following:
75%(up to 75% electrial energy consumption)
Previous setting mode.
Under GEAR operation, the display on the remote controller will alternage between electical
energy consumption and set temperature.
Press this button
The unit will operate at
the biggest capacity
Turbo
Turbo
output to reach the
setting Temp. quickly.
Press this button to activate Turbo feature. It enables the unit to reach the set temperature in the shortest time.
Press it again to disable it.(Model dependent)
09
2s
Keep pressing this button more
Swing
than 2 seconds, the vertical louver
swing function is activated.
(Model dependent)
GEAR(50%) Previous setting mode ECO......
O
O O
50%(up to 50% electrial energy consumption)
SET
Press the SET button to enter the function setting, then press SET button or TEMP
button to select the desired function. The selected symbol will flash on the display area, press the
OK button to confirm.
To cancel the selected function, just perform the same procedures as above.
Press the SET button to scroll through operation functions as follows:
Fresh (
[ ]: Model dependent *
NOTE: If your remote controller has sleep button, you can not use the SET
FRESH function(
SET
When the FRESH function is initiated, the Ionizer/Plasma Dust Collector(depending
on models) is energized and will help to remove pollen and impurities from the air.
Sleep function(
The SLEEP function is used to decrease energy use while you sleep(and don't need
O O
the same temperature settings to stay comfortable). This function can only be activated
via remote control. For the details, see "Sleep operation" in "USER'S MANUAL".
NOTE: The SLEEP function is not available in FAN and DRY mode.
O O
Follow me function(
The FOLLOW ME function enables the remote control to measure the temperature at its current location
and send this signal to the air conditioner every 3 minutes interval. When using AUTO, COOL or HEAT
modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself) will
enable the air conditioner to optimize the temperature around you and ensure maximum comfort.
NOTE:
If the memory feature is activated, "
If the memory feature is stopped, "
While the memory feature is activated, press the ON/OFF button, shift the mode or power failure
will not cancel the Follow me function.
AP function(
Choose AP mode to do wireless network configuration. For some units, it doesn't work by pressing
the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.
SET
or
*
* *
) Sleep ( ) Follow Me( ) AP mode ( )
   
button to select the sleep feature.
) (some units) :
) (some units) :
) :
Press and hold Turbo button for seven seconds to start/stop memory feature of Follow Me function.
On "
displays for 3 seconds on the screen.
OF "
displays for 3 seconds on the screen.
)(some units) :
OK
or TEMP
Fresh ....
10