Advertisement
Remote Control Buttons and Functions
✎
This is a special remote control for the visually impaired and has Braille points on the Power, Channel and Volume buttons.
Turns the TV on and off.
Displays and selects the available video sources.
Press to directly access channels.
Press to select additional channels (digital) being
broadcasted by the same station. For example, to select
channel "54-3", press "54", then press "–" and "3".
Adjusts the volume.
Brings up the OSD.
Views Media Play (USB).
Quickly select frequently used functions.
Returns to the previous menu.
Buttons used in the Channel list, Media Play (USB)
menu, etc.
Use these buttons in Media Play (USB) and Anynet+
POWER
(HDMI-CEC) modes. (�: Controls recording on
Samsung recorders that have the Anynet+ feature)
POWER
Changing Channels and Adjusting the Volume
Adjust the volume by pressing the Volume button
on the remote.
MEDIA.P
✎
You can also change the channels by pressing the z button on the front panel of your TV and adjust the volume by pressing the y button.
TOOLS
Viewing the On Screen Menus
RETURN
To view the On Screen Menus, follow these steps:
MEDIA.P
A
1. Turn on your TV, press the
MENU
button on your
remote. The main menu appears.
TOOLS
S.MODE
The menu's left side has the following menu
P.MODE
options: Picture, Sound, Channel, Setup, Input, Application, and Support.
RETURN
2. Press the ▲ or ▼ button on your remote to select a menu option, and then
press the ENTERE button.
A
3. When done using the menu, press the
EXIT
button on your remote to exit.
S.MODE
Selecting a Source
P.MODE
To watch a movie on your Blu-ray player or watch
your favorite TV show, you must select the correct
POWER
source. A source is a device, such as a Blu-ray/DVD
player, a cable/satellite box, antenna or a cable TV
input. Sources can be connected to your TV through
the HDMI, DVI, Component, Composite, or D-sub
connections, or through the Antenna or Cable In connections.
To view the signal from a source connected to the HDMI, DVI, Component,
Composite, or D-sub jack, press the
SOURCE
button on your remote. Each time
you press the
SOURCE
button, you change to a different source.
MEDIA.P
POWER
ON/OFF
SOURCE
Turns the remote control light on or off. When on, the
buttons become illuminated for a moment when pressed.
(Using the remote control with this button set to off will
reduce the battery usage time.)
Returns to the previous channel.
PRE-CH
Cuts off the sound temporarily.
Changes channels.
CH LIST
Displays the channel list on the screen.
MENU
MEDIA.P
FAV.CH
Displays Favorite Channel Lists on the screen.
TOOLS
INFO
Displays information on the TV screen.
Selects the on-screen menu items and changes the values
seen on the menu.
RETURN
EXIT
Exits the menu.
A
B
C
D
S.MODE: Press to select the sound mode.
S.MODE
SLEEP
MTS
SLEEP: Automatically shuts off the TV at a preset time.
P.MODE
P.SIZE
CC
MTS: Press to choose stereo, mono or Separate Audio
Program (SAP broadcast).
ON/OFF
P.MODE: Press to select the picture mode.
P.SIZE: Selects the picture size.
SOURCE
CC: Controls the caption decoder.
ON/OFF
SOURCE
PRE-CH
Change the channels by pressing the Channel button on the remote.
✎
CH LIST
If your TV is attached to a cable or satellite box, change the channel using
MENU
the box's remote.
FAV.CH
PRE-CH
INFO
Using Auto Motion Plus
EXIT
CH LIST
Auto Motion Plus 120Hz™ technology virtually eliminates any blur in video that
MENU
B
C
FAV.CH
D
include fast motion such as sports and action movies. To activate Auto Motion
Plus, follow these steps:
SLEEP
MTS
INFO
1. Turn on your TV, press the
MENU
button on your remote, then select Picture
P.SIZE
CC
Options → Auto Motion Plus 120Hz.
EXIT
2. Select the Auto Motion Plus 120Hz setting you want.
✎
If noise occurs on the screen, please set up the Auto Motion Plus
B
C
D
120Hz to Off. If Auto Motion Plus 120Hz is Custom, you can set up
SLEEP
MTS
the Blur Reduction, Judder Reduction or Reset manually.
✎
P.SIZE
CC
If Auto Motion Plus 120Hz is Demo, you can compare the difference of
on and off modes.
3. Press the
RETURN
button on your remote when done.
ON/OFF
SOURCE
PRE-CH
CH LIST
MENU
FAV.CH
Step 6
: The Internet@TV and Media Play Features
Your TV's Internet@TV feature lets you connect to an ever-expanding portal of your
favorite on-line digital content. Customizable widgets give you access to Blockbuster,
Facebook, YouTube, Flickr, Netflix* and more - all on your HDTV. The Media Play
feature lets you connect to your PC through your home network and stream PC audio
and video files to your HDTV using your remote. To use IPTV or Samsung PC Share
Manager, you must connect your TV to your network. You can attach the TV to your
network in two ways, by cable, using CAT 5 cable, or wirelessly, using a Samsung
Wireless LAN Adapter. Instructions for both connection methods are below.
Network Connection - Wired
There are two main ways to connect your TV to your network using cable,
depending on your network setup. They are illustrated below:
The Modem Port on the Wall
TV Rear Panel
External Modem
(ADSL / VDSL / Cable TV)
Modem Cable (Not Supplied)
LAN Cable (Not Supplied)
TV Rear Panel
The LAN Port on the Wall
LAN Cable (Not Supplied)
Configuring the Network Connection - Wired
Most home networks use the
Network Setup
Dynamic Host Configuration Protocol
Internet Protocol Setup : Auto
(DHCP) to configure network
IP Address
:
connections. Home networks that
Subnet Mask
:
support DHCP automatically provide
Gateway
:
the IP address, subnet mask,
gateway, and DNS values your TV
DNS
: Auto
needs to access the Internet so you
DNS Server
:
don't have to enter them manually.
To configure your network connection
U Move E Enter R Return
for a network that uses DHCP, follow
these steps:
1. Connect your TV to your network as shown in one of the illustrations above.
2. Turn on your TV, press the
MENU
button on your remote, and then select
Setup → Network.
3. Set the Network Type to Wired if it is not already set to Wired.
4. Select Network Setup. The Network Setup screen appears.
5. On the Network Setup menu, set Internet Protocol Setup and DNS to Auto.
Auto acquires and enters the necessary internet values automatically.
6. Select Network Test to check Internet connectivity.
✎
Some networks are Static IP networks. If your network is a Static IP network,
you can not use DHCP to configure the network connection. Instead, you
must enter the IP Address, Subnet Mask, Gateway, and DNS Server
manually. For instructions explaining how to configure a Static IP network,
see your user's manual.
Network Connection - Wireless
You can connect your TV to your LAN through a standard wireless router or
modem. To connect wirelessly, you must first attach a "Samsung Wireless LAN
Adapter" (WIS09ABGN - sold separately) to either the
USB1 (HDD)
on the back of your TV. See the illustration below.
Samsung Wireless LAN
Wireless IP
The LAN Port on the Wall
sharer
LAN Cable (Not Supplied)
Samsung's Wireless LAN adapter supports the IEEE 802.11A, IEEE 802.11B, IEEE
802.11G, and IEEE 802.11N wireless communication protocols. For your TV to
connect to your network, the wireless router or modem you use must also support
one of these protocols. The fastest of these protocols is IEEE 802.11N.
Most wireless network systems incorporate a security system that requires devices
that access the network through an access point or AP (typically a wireless modem
or router) to transmit an encrypted security code called an access key.
FWhen connecting Samsung Wireless LAN Adapter to TV in 802.11N mode, WEP/
TKIP/TKIP-AES is not supported.
Configuring the Network Connection - Wireless
The instructions below are for networks that use the Dynamic Host Configuration
Protocol (DHCP) to configure network connections automatically. If your have a
Static IP network, see your user's manual for configuration instructions.
To configure your network connection for a network that uses DHCP, follow these
steps:
r
1. Connect your TV to your network as shown in the illustrations above.
2. Turn on your TV, press the
MENU
button on your remote, and the select Setup
→ Network.
3. Set the Network Type to Wireless if it is not already set to Wireless.
4. Select Network Setup. The Network Setup screen appears.
5. On the Network Setup menu,
Network Setup
select an AP(Access Point) and
Select a network
ad hoc network. if you have
Internet Protocol Setup : Auto
selected network with a security
IP Address
key, the Security Key screen
Subnet Mask
appears.
Gateway
6. Enter the security key using the
DNS
numbers on the remote, and then
DNS Server
press the Blue button on your
remote.
✎
If your network uses WEP
security encryption, 0~9 and A~F will be available on the Security
Key screen. Use the Direction button on your remote to move to the
characters and the enter key to select them.
7. On the Network Setup menu, set Internet Protocol Setup and DNS
Setup to Auto. The Auto acquires and enters the necessary internet values
automatically.
8. Select Network Test to check internet connectivity.
✎
For more information, see your user's manual.
Connecting a USB Device for Media Play
You can enjoy photo, music, and movie files stored on a USB device by connecting
it to the TV and using the
Media Play feature. For
MediaPlay
Media Play operating
instructions, please see
Videos
your Owner's Manual.
Change Device
SUM
BN68-02629A-01
or
USB2
port
TV Side Panel
Adapter
or
: Not Selected
r
:
:
:
: Auto
:
U Move E Enter R Return
View Devices E Enter R Return
Advertisement
