Table of Contents
Advertisement
Quick Links
1.
OVERVIEW ................................................................................................................................... 1
2.
SPECIFICATIONS ......................................................................................................................... 3
2.1. ONE-TO-ONE NAT ............................................................................................................... 3
2.2. VLAN BASED NAT ............................................................................................................... 3
2.3. PORT BASED NAT .............................................................................................................. 3
2.4. SFP MODULES .................................................................................................................... 3
2.5. PHYSICAL (NUMBER OF SLOTS) ...................................................................................... 3
2.6. ORDERING INFORMATION ................................................................................................. 3
3.
INSTALLATION ............................................................................................................................. 5
3.1. REAR PLATE DESCRIPTION .............................................................................................. 5
3.1.1. Ethernet Connection Control ...................................................................................... 6
3.2. HARDWARE INSTALLATION .............................................................................................. 7
3.2.1. Installing in 3700FR Frame ........................................................................................ 7
3.2.2. Installing in EMX3 ...................................................................................................... 8
3.2.3. Installing in EMX6 ...................................................................................................... 8
3.3. CONFIGURING THE BASIC NETWORK SETTINGS ......................................................... 11
3.4. CONNECTING TO VLPRO ................................................................................................. 12
4.
CARD CONFIGURATION ........................................................................................................... 13
4.1. GENERAL TAB .................................................................................................................. 13
4.2. ETHERNET PORT MONITOR TAB .................................................................................... 14
4.3. FLOW CONTROL TAB ....................................................................................................... 16
4.3.1. IP NAT ..................................................................................................................... 16
4.3.2. VLAN based NAT .................................................................................................... 18
4.3.3. PORT based NAT .................................................................................................... 20
4.3.4. CLEAR TAB ............................................................................................................. 22
5.
TROUBLESHOOTING ................................................................................................................. 23
5.1. UPDATING VLPRO SERVER JAR FILE ............................................................................ 23
EMX3/EMX6/3000FR/3700 MultiFrame Manual
3080IPG-NAT-2-10GE High Density Network Address Translator
TABLE OF CONTENTS
Revision 1.0
Page i
Advertisement
Table of Contents
Related Manuals for evertz MultiFrame EMX3
Summary of Contents for evertz MultiFrame EMX3
-
Page 1: Table Of Contents
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator TABLE OF CONTENTS OVERVIEW ........................... 1 SPECIFICATIONS ......................... 3 2.1. ONE-TO-ONE NAT ....................... 3 2.2. VLAN BASED NAT ....................... 3 2.3. PORT BASED NAT ......................3 2.4. SFP MODULES ........................3 2.5. - Page 2 EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator Figures Figure 1-1: 3080IPG-NAT-2-10GE Block Diagram ..................2 Figure 2-1: Universal Rear Plate for 3080IPG-NAT-2-10GE ................5 Figure 3-2: 3700FR Frame Ethernet Port ......................7 Figure 3-3: EMX-3 Frame Ethernet Port ......................8 Figure 3-4: EMX-6 Frame Ethernet Port ......................
- Page 3 Feb 2014 Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning performance of Evertz products are for informational use only and are not warranties of future performance either express or implied.
- Page 4 EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator This page left intentionally blank Page iv Revision 1.0...
-
Page 5: Overview
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator OVERVIEW The 3080IPG-NAT platform is a complete hardware based solution to remove the need for service providers to enforce address range restrictions and VLAN schemes for their customers in multi-tenant environments. Controlled by the industry leading VistaLINK PRO, the 3080IPG-NAT-2-10GE is a high density Network... -
Page 6: Figure 1-1: 3080Ipg-Nat-2-10Ge Block Diagram
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator 1/10GigE 1/10GigE (SFP 2) (SFP 1) IP Address IP Receiver Translator Mode Select Decapsulator IP Receiver Encapsulator (VLAN filter) 1/10GigE 1/10GigE (SFP 3) (SFP 4) IP Address IP Receiver Translator Mode Select Decapsulator IP Receiver... -
Page 7: Specifications
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator SPECIFICATIONS 2.1. ONE-TO-ONE NAT • 2048xstatic mapping 2.2. VLAN BASED NAT • 2048xVLAND ID mapping 2.3. PORT BASED NAT • 2xdatagrams flow mapping (from 2x1/10GE) 2.4. SFP MODULES • 4xSFP Modules •... - Page 8 EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator This page left intentionally blank Page - 4 SPECIFICATIONS Revision 1.0...
-
Page 9: Installation
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator INSTALLATION 3.1. REAR PLATE DESCRIPTION The 3080IPG-NAT comes standard with a companion +6RU rear plate. Figure 2-1 provides an illustration of the 3080IPG-NAT rear plate. Figure 2-1: Universal Rear Plate for 3080IPG-NAT-2-10GE INSTALLATION Page - 5 Revision 1.0... -
Page 10: Ethernet Connection Control
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator 3.1.1. Ethernet Connection Control The 3080IPG-NAT Series uses 10Base-T (10 Mbps), 100Base-TX (100 Mbps) or Gigabit (1Gbps) twisted pair Ethernet cabling systems. When connecting for 10Base-T systems, category 3, 4, or 5 UTP cable as well as EIA/TIA –... -
Page 11: Hardware Installation
PRO Server IP address. ® 4. 3700FC or EMX-FC (depending on the Evertz frame used) for facilitating network communications between the frame modules and the configuration software. Before handling the card it is important to minimize the potential effects of static electricity. It is therefore recommended that an ESD strap be worn. -
Page 12: Installing In Emx3
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator 3.2.2. Installing in EMX3 For proper functionality, the Frame Controller should be inserted into the Left most slot, and the Ethernet connection to the network be inserted into the RJ-45 connector titled Ethernet 1B on the rear of the frame (see Figure 3-3 Red Square on the right). -
Page 13: Figure 3-4: Emx-6 Frame Ethernet Port
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator Figure 3-4: EMX-6 Frame Ethernet Port Before inserting the front card, connect the serial cable to the board using the serial cable provided (See figure 2-2 for reference). Now insert the 3080IPG-NAT card into the corresponding front slots ensuring the card lines up with the slot runners on the bottom and the top of the chassis. -
Page 14: Figure 2-2: Serial Connection For 3080Ipg-Nat
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator Figure 2-5: Serial Connection for 3080IPG-NAT Click OK to apply these settings and press the return key. The session should respond with the 3080IPG- NAT Main Menu (see Figure 2-3): Figure 2-6: 3080IPG-NAT Serial Menu Page - 10 INSTALLATION Revision 1.0... -
Page 15: Configuring The Basic Network Settings
This sub-menu is used to configure the 3080IPG_NAT functions through the serial menu 5) Trace – Engineering Only This menu is for Evertz technical support staff only. You may be requested to access and execute the available options to enable the viewing of certain system events during troubleshooting. -
Page 16: Connecting To Vlpro
PRO finds the card and confirms its configuration. ® Please consult your network administrator if you continue to have problems connecting the card with VistaLINK PRO, alternatively contact Evertz Microsystems Ltd. or your authorized reseller for technical ® support. Page - 12 INSTALLATION Revision 1.0... -
Page 17: Card Configuration
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator CARD CONFIGURATION Right click the IP address of the 3080IPG-NAT to access and configure their parameters. Select “View Configuration”. The configuration page will open, enabling the user to toggle the configuration tabs in order to configure the parameters of the 3080IPG-NAT. -
Page 18: Ethernet Port Monitor Tab
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator • Flow Count: Displays the number of flows configured on the card. Port 1 - 4: • IP Address: Set the IP Address for corresponding Ethernet port, a reboot is required after modifying this field. -
Page 19: Figure 4-2: Ethernet Ports Monitor Tab
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator Figure 4-2: Ethernet Ports Monitor Tab Port 1 Monitor: • Link Status (Port 1): This parameter returns the lin kStatus for IP Ports. • Link Speed: Displays the link speed in Mbps for given ethernet port. Received: •... -
Page 20: Flow Control Tab
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator • Broadcast Frames Received: This parameter returns number of broadcast packets received. • Unicast Frames Received: This parameter returns number of unicast packets received. • Multicast Frames Received: This parameter returns number of multicast packets received. Transmitted: •... -
Page 21: Figure 4-3: Ip Nat - Flow Control Tab
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator Figure 4-3: IP NAT - Flow Control Tab Flow: Index for various flows, around 2048 different flows can be configured on one NAT. Note: Flows 1-1024 correspond to ports 1 & 2 only whereas flows 1025-2048 correspond to ports 3 &... -
Page 22: Vlan Based Nat
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator Output Control: • Flow Output Mode: Allows user to select mode for the flow. o Disable: No output. o Passthrough: Nothing changes in the header of IP packet. o Modify: Modifies the packet based on the other parameters. •... -
Page 23: Figure 4-4: Vlan Based Nat - Flow Control Tab
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator Figure 4-4: VLAN based NAT - Flow Control Tab Flow: Index for various flows, around 2048 different flows can be configured on one NAT. Note: Flows 1-1024 correspond to ports 1 & 2 only whereas flows 1025-2048 correspond to ports 3 &... -
Page 24: Port Based Nat
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator • Output Destination IP Address: Control used in VLAN-Based NAT mode for specifying the destination IP address. Outgoing packets of the flow will be encapsulated with given destination IP address. • Output Source UDP Port: Control used in VLAN-Based NAT mode for specifying the source UDP port . -
Page 25: Figure 4-5: Port Based Nat - Flow Control Tab
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator Figure 4-5: PORT based NAT - Flow Control Tab Flow: Index for various flows, up to 2048 different flows can be configured on one NAT. NOTE: Flows 1-1024 correspond to ports 1 & 2 only whereas flows 1025-2048 correspond to ports 3 &... -
Page 26: Clear Tab
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator • Output Source UDP Port: Control used in Port-Based NAT mode for specifying the source UDP port . Outgoing packets of the flow will be encapsulated with given source UDP port. •... -
Page 27: Troubleshooting
UPDATING VLPRO SERVER JAR FILE Evertz products are constantly evolving and new features are often added. It is therefore important to update the JAR files in use to provide access to all the latest features or enhancements. It will also be necessary to add JAR files for new products. -
Page 28: Figure 5-2: Vistalink Pro - Applying Jar Updates
EMX3/EMX6/3000FR/3700 MultiFrame Manual 3080IPG-NAT-2-10GE High Density Network Address Translator Figure 5-2: VistaLINK PRO – Applying JAR Updates ® You will be prompted to restart the server to enable the change to take effect. Apply as many JAR updates as required before restarting the server. ...
Need help?
Do you have a question about the MultiFrame EMX3 and is the answer not in the manual?
Questions and answers