Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nordic MT-L0118
Summary of Contents for Nordic MT-L0118
- Page 1 18V CORDLESS MULTI-TOOL OPERATING MANUAL MT-L0118...
-
Page 2: Product Specification
NORDIC PRODUCT SPECIFICATION Voltage: Speed n 11,000-21000min Vibration: 4.851m/s , K=1.5m/s A weighted sound pressure level: LpA: 79.2dB(A) ; KpA=3dB(A) A weighted sound power level: LwA: 90.2dB(A) ; KwA=3dB(A) GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and instructions. Failure to heed warnings and follow instructions may result in electric shock, fire and/or serious injury. -
Page 3: Personal Safety
NORDIC • Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and refrigerators. There is an increased risk of an electric shock if your body is earthed. • Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will increase the risk of an electric shock. - Page 4 NORDIC the power tool or these instructions to operate it. Power tools are potentially dangerous in the hands of untrained users. • Maintain power tools. Check for misalignment or jammed moving parts, breakages or any other feature that might affect the operation of the power tool. If it is damaged, the power tool must be repaired. Many accidents are caused by using poorly maintained power tools.
- Page 5 NORDIC Ensure that you have removed foreign objects such as nails and screws from the workpiece before commencing sanding. Don’t use it for wet sanding, for dry sanding only. Do not scrape wet or dampened materials (e.g. wallpaper) or on moist surfaces. Penetration of water into the machine increases the risk of an electric shock.
-
Page 6: Additional Safety Instructions For Batteries And Chargers
NORDIC ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND CHARGERS Use only batteries and chargers applicable for this machine. 4.1 BATTERIES • Never attempt to open for any reason. • Do not store in locations where the temperature may exceed 40 °C. - Page 7 NORDIC SYMBOLS In this manual and/or on the machine the following symbols are used: Denotes risk of personal injury or damage to the tool. Read manual before use Wear eye protection Wear ear protection Wear safety gloves In accordance with essential requirements of the European directive(s) Class II - The machine is double insulated;...
-
Page 8: Operation
NORDIC OPERATION BATTERY CHARGER The lithium-ion battery can be charged at any time and will not develop a “memory” when charged after only a partial discharge. It is not necessary to run down the battery pack charge before recharging. Remove the battery pack from the tool when convenient for you and your job. - Page 9 NORDIC FUNCTIONS ATTACHING THE APPLICATION TOOL CAUTION: For all work or when changing application tools, disconnect the battery pack from power tool and always wear protective gloves. The sharp edges of the application tools will cause personal injury. Application tools can be very hot while working.
-
Page 10: Variable Speed Control
NORDIC period, and then switch on the tool. The burr will form a non-slip bond with the outer edge of the sand paper felt. This will avoid premature wear. If one point has become worn, pull off the sandpaper, turn it 120°... -
Page 11: Cleaning And Maintenance
NORDIC • Flush cutting blades are intended to make precise cuts to allow for installation of flooring or wall material. When flush cutting, it is important not to force the tool during the plunge cut. If you experience a strong vibration in your hand during the plunge cut, this indicates that you are applying too much pressure. - Page 12 NORDIC Quick-release lever Sanding paper On/off switch Scraper Release button(battery pack) Plunge cut blade PLEASE NOTE: Battery & Charger sold seperately. Battery pack(not included) Sanding base...
Need help?
Do you have a question about the MT-L0118 and is the answer not in the manual?
Questions and answers