Furuno 1722 Quick Start Manual page 7

NAVNET 7" Display
NOTES:
Radar (17X2/C type) display
DATA 1 same as 10.4"
DATA 2 heading only!
DATA 3 same as 10.4" DATA 4
Plotter (GP1700C)
DATA 1 same as 10.4"
DATA 2 NMEA input/output
DATA 3 same as 10.4" DATA 4
NOTE: These are examples of NavNet
wiring. Please contact Furuno or a local
authorized dealer for more advanced or
special configurations.
NavNet displays input & output NMEA data in
RS422 (+/-) and RS232 (+/ground) voltage levels,
use the appropriate connections as required.
NAVNET 10.4"
Display
NOTES:
Waypoint information
DATA 1
from a external GPS is
possible by menu
selection.
Press [MENU],
[PLOTTER SETUP],
select [QP], edit QP to
"EXT WPT (RMB)"
and press [ENTER].
DATA 2
PORT PRIORITIES:
HIGHEST:
(*BBWGPS overrides
all ports)
NETWORK PORT
(any position data
coming in to display)
DATA 3
DATA 4 (NMEA I/O)
DATA 2 (NMEA I/O)
DATA 1 (NMEA I/O)*
LOWEST:
DATA 4
remaining wire colors
for 000-144-418 cable
are same as shown
on AIR-033-407 adapter
DATA 4
AIR-033-407 adapter cable
( direct connection of smart sensor to DATA 4)
NAVNET Wiring Configurations
Power supply connections are omitted for clarity
Refer to appropriate installation manual for more information
Connect BBWGPS
attached cable
directly to the
NavNet display
yellow
NMEA
input(+)
Furuno BBWGPS
OR
(one only!)
000-144-418 (5m) cable
(NMEA input/output)
000-117-603 (5m) cable
white (NMEA output +)
black (NMEA output -)
yellow (NMEA input +)
from ext.
NMEA device
green (NMEA input -)
(NMEA input/output)
000-117-603 (5m) cable
white (NMEA heading)
black (NMEA heading)
OR
(one only!)
(Furuno
AD10 or NMEA Heading only)
000-144-418 (5m) cable
blue (input RS232)
white (output RS232)
bare wire (common ground)
RS422 + input (yellow)
RS422 - input (green)
OR
(one only!)
7(P)
NMEA output(white RS232)
plug
NMEA input (blue RS232)
ext. buzzer (black)
+12VDC (red)
common ground(bare wire) for
12VDC, RS232 I/O & buzzer
Terminal
Block
(local supply)
000-145-612 (1.2m) cable
(included with GP32)
green
NMEA
input(-)
Terminal
Block
(local supply)
000-125-237 cable supplied with PG1000
Terminal
Block
000-145-612 (1.2m) cable
(local supply)
use AIR-033-407 adapter for DATA 4 (connect direct to DATA 1)
white
NMEA
output(+)
RS422
blue
NMEA
output(-)
RS422
NMEA input
cable (local supply)
NMEA input
cable (local supply)
Heading output
(NMEA)
cable (local supply)
(included with GP32)
yellow (output RS232)
green (input RS232)
blue (common ground)
FURUNO
BBWGPS
antenna
OR
FURUNO GP32
GPS system
OR
other external
GPS unit
(follow
manufacturer
wiring
specifications)
VHF RADIO
(DSC input)
DATA2 shown
OR
use DATA4
RS232 NMEA
output for RS232
level requirement
AND/OR
Autopilot
FURUNO
PG1000
FURUNO GP32
GPS system
OR
other external
GPS unit
(follow
manufacturer
wiring
specifications)
OR
FURUNO
SMART
DEPTH SENSOR