Advertisement
Quick Links
Advertisement
Related Manuals for KMART 50cm Racer
Summary of Contents for KMART 50cm Racer
- Page 1 Item No.: 43033430 Item Name: 50cm Racer...
- Page 2 Contents Parts identification …………………………………… 1 Safety precautions …………………………………… Assembly …………………………………… … Adjustment …………………………………… … Repair and Service ………… …………………………… Warranty ……………………………………...
- Page 3 NAME OF RACER PARTS...
- Page 4 Not intended for jumping. The brake may be hot after continuous use. Do not touch after braking. Check brakes and secure all fasteners before every ride. Do not wear headphones or anything else that would impair your ability to hear or see. Understand all operating procedures before riding.
- Page 5 Do not push the product. Do not tow or pull any objects with the product. Replace worn or broken parts immediately. Know your limits. Be familiar with your abilities. Use common sense. Not suitable for children under 3 years as small parts may cause a choking hazard. Handlebar hand grips and tube end plugs should be replaced if damaged, as bare tube ends have been known to cause injury.
- Page 6 WARNING: Keep small parts away from children during assembly. Note: All of the directions(right, left, front, rear, etc.) in this manual are seen by the rider while seated on the unit. Tools required(Not included in the packing)
- Page 7 Parts assembly view...
- Page 8 Parts assembly List Caution: Check parts list first, stop assembly if any parts missing or defective Seat Wheel Retainer (x2) Screw - Long (x2) Wheel Bushing (x4) Washer (x2) Nut (x2) Cap (x2)
- Page 9 Parts Assembly Note: Please do not assembly in wrong Handlebar Installation direction. Stem(1) and fork(2) are pre-installed. The stem (1) is installed upside down for packaging and must be adjusted before assembly handlebar.Turn the fork so it faces forward. Make sure that the stem(1) is pointing upward and facing the same direction as the fork(2) and brake calipers(3) are facing forward.
- Page 10 Parts Assembly Tightening Tests: Test the tightness of the stem bolts: Straddle the front wheel and hold it between your legs. Gently try to turn the front wheel by turning the handlebar. If the handlebar and stem turn on the fork realign the stem with the wheel and tighten the stem bolts tighter than before(about 1/4 revolution at a time) Repeat this test until the stem does not move on the fork.
- Page 11 Parts Assembly Rear Frame Installation Steps: 1. Slide the Rear Frame (12) into the Main Frame (1) Bracket. 2. Install the Bolts (18) and Washers (19) through the Frame holes. 3. Install the lower Washers (19) and Nuts (20). 4. Tighten securely. WARNING: Frame bolts must be suf ciently tightened to ensure they do not come loose.
- Page 12 Parts Assembly Rear Wheel Installation Steps: 1.Install the Rear Wheels (14) as shown. 16 15 The rear bushings are pre-installed into the concave Frame (12) on most models. If they are not part pre-installed, push each into the frame until FINAL it is fully seated.
- Page 13 Parts Assembly Front Frame Installation If the distance of two brake shoes not wide enough to put rim in ,loosen the brakes (A). This will allow the tyre to fit between the brake pads. NOTE: Turn unit upside down before installing Wheel Assembly. WARNING: Ensure the front wheel is installed correctly so that when pedaled the unit moves forward.
- Page 14 Parts Assembly Front Wheel Installation Steps: 1. Place a Wheel Bushing (25) in each fork end as shown next page. 2. Make sure Right Crank is on the Right side of the unit. 3. Place Wheel (30) so that both Bearings (A) set in the Wheel Bushings.
- Page 15 Parts Assembly Pedal Installation NOTE: There is a pedal marked “R” and a pedal marked “L”. • The pedal marked “R” has right hand threads. Insert it into the crank arm on the right side. Tighten it in a clockwise direction. •...
- Page 16 Parts Assembly Seat Installation NOTE: Make sure the longer bolts(8) IN THE MIDDLE HOLES are used for seat assemble. The rest 4 short screws(9) in the front & back 4 holes just for through frame bracket holes. No use for assemble. Remove 2 screws away from the middle holes(A) Position the Seat (7)over the frame bracket...
- Page 17 Brake System Adjustments WARNING:You must adjust the front brakes as BRAKE SHOE written before you ride the unit. 1.Put the brake shoes in the correct position: Loosen the nut (1)of each brake shoe. Adjust each brake shoe so it is flat against the rim and aligned with the curve of the rim.
- Page 19 The following sections describe final brake system adjustments required before riding.Determine which style you have and follow the instructions.
- Page 22 Repair and Service Periodic maintenance is required to ensure the product continues to operate properly. If any part of the product does not operate properly – discontinue use. Keep the product clean and free of dirt, dust and water. This will prolong the useful life of the product.
- Page 23 Repair and Service In ating the Front Tyre: Use a hand or a foot pump to inflate the tyre. Service station meter-regulated air hoses are also acceptable. The maximum in ation pressure is shown on the tyre sidewall. If two inflation pressures are on the tyre sidewall, use the higher pressure for on-road riding and the lower pressure for off-road riding.
- Page 24 Australian Consumer Law. Kmart will provide you with your choice of a refund, repair or exchange (where possible) for this product if it Please retain your receipt as proof of purchase and contact our Customer Service Centre on 1800 124 125 be addressed to our Customer Service Centre at 690 Springvale Rd, Mulgrave Vic 3170.