Lynx BRP REX2 Adventure LX 600 ACE Operator's Manual
  1. Manuals
  2. Brands
  3. Lynx Manuals
  4. Snowmobiles
  5. BRP REX2 Adventure LX 600 ACE
  6. Operator's manual

Lynx BRP REX2 Adventure LX 600 ACE Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2018
REX
2
Touring / Utility
Read this guide thoroughly. It contains important
safety information.
Minimum recommended operator's age: 16 years old.
Keep this Operator's Guide in the vehicle.
6 1 9
9 0 0
9 3 8
Original Instructions

Advertisement

Table of Contents
loading

Related Manuals for Lynx BRP REX2 Adventure LX 600 ACE

Summary of Contents for Lynx BRP REX2 Adventure LX 600 ACE

  • Page 1 2018 Touring / Utility Read this guide thoroughly. It contains important safety information. Minimum recommended operator’s age: 16 years old. Keep this Operator’s Guide in the vehicle. 6 1 9 9 0 0 9 3 8 Original Instructions...
  • Page 2 ©...
  • Page 3 This vehicle may exceed the performance of other vehicles you may have ridden in the past. Take time to familiarize yourself with your new vehicle. Lynx products are manufactured by BRP. The following are trademarks of Bombardier Recreational Products Inc. or its sub- sidiaries.

  • Page 4: Foreword

    Bombardier Recreational Products your new vehicle was prepared to your Inc. (BRP) warranty and a network of entire satisfaction. authorized Lynx snowmobile dealers ready to provide the parts, service or Know Before you Go accessories you may require. To learn how to reduce the risk for you,...

  • Page 5: Safety Messages

    FOREWORD We highly recommend that you take The following terminology in regards to a safety riding course. Please check operator, passenger and vehicle con- with your dealer or local authorities for figuration is used as follows through- availability in your area. out this guide: –...

  • Page 6: Table Of Contents

    TABLE OF CONTENTS FOREWORD ................1 Know Before you Go .
  • Page 7 TABLE OF CONTENTS CONTROLS, INSTRUMENTS AND EQUIPMENT (cont’d) 9) Drive Belt Guard ............. . 45 10) Gauge .
  • Page 8 TABLE OF CONTENTS TUNE YOUR RIDE ..............88 Rear Suspension Adjustments.
  • Page 9 Fault Codes ..............150 WARRANTY BRP FINLAND OY INTERNATIONAL LIMITED WARRANTY: 2018 LYNX ®...

  • Page 10: Safety Information

    SAFETY INFORMATION ________ ________ SAFETY INFORMATION...

  • Page 11: General Precautions

    To reduce the risk of fire or explo- standards. sion, follow these instructions: – Use only an approved gasoline con- See your authorized Lynx dealer for tainer to store fuel. available accessories for your vehicle. – Strictly adhere to instructions in ELING PROCEDURE –...

  • Page 12: Special Safety Messages

    SPECIAL SAFETY MESSAGES SEVERE INJURY OR DEATH can result if you do not follow these instructions: – Always make a pre-ride inspection BEFORE you start the engine. – Throttle mechanism should be checked for free movement and return to idle po- sition before starting engine.
  • Page 13 SPECIAL SAFETY MESSAGES – Know your local laws. Federal, state, provincial and local government agencies have enacted laws and regulations pertaining to the safe use and operation of snowmobiles. It is your responsibility as a snowmobiler to learn and obey these laws and regulations.
  • Page 14 – You may stud the track on this vehicle model. However, you MUST only use the BRP approved type stud for use on Lynx snowmobiles. DO NOT EVER use con- ventional studs because the track thickness is thinner then our standard tracks.
  • Page 15 SPECIAL SAFETY MESSAGES – Do not forget, with 2-UP models, the operator is responsible for the safety of the passenger. Always remember that the snowmobile handling, stability and brak- ing distance may be affected when riding with a passenger. – Before riding the vehicle, ask your passenger to inform you to slowdown or stop immediately if he feels uncomfortable or insecure during the ride.

  • Page 16: Active Technologies (Itc) (Ace)

    Learning Key Modes operation of its system within set pa- The Lynx learning key limits the rameters. torque and speed of the snowmobile It is extremely important for opera-...

  • Page 17: Riding The Vehicle

    Hood and side panels must mobile. Each visit to your authorized be also properly latched. Lynx dealer is a great opportunity for 6. Activate the throttle control lever your dealer to verifiy if your snowmo- several times to check that it oper- bile is included in any safety campaign.

  • Page 18: How To Ride

    RIDING THE VEHICLE VEHICLE WARM UP 2. Check the engine cut-off switch (by 4. Refer to the pulling tether cord cap) and emer- section and follow instructions. gency engine stop switch opera- tion. Pre-Ride Check List 3. Release parking brake. ✔...
  • Page 19 RIDING THE VEHICLE face mask should always be carried Generally, the riding position for best or worn. Goggles or a face shield that balance and control is sitting. How- attach to the helmet are indispensable. ever, the posting, kneeling or standing positions are also used under certain Hands should be protected by a pair conditions.

  • Page 20: Carrying A Passenger

    RIDING THE VEHICLE Kneeling WARNING This position is achieved by placing Unexpected acceleration when one foot firmly on the running board snowmobile operates in reverse and the opposite knee on the seat. can cause a loss of control. Avoid abrupt stops. Carrying a Passenger Certain snowmobiles are designed for an operator only (1-UP), and others...

  • Page 21: Terrain/Riding Variations

    RIDING THE VEHICLE For complete information on how to WARNING adjust the suspension, please refer to – Passenger must only sit on des- TUNE YOUR RIDE subsection. ignated passenger seat. Never allow anyone to sit between the Riding with a Child handlebar and the operator.
  • Page 22 RIDING THE VEHICLE capable of vehicle control. Beware of ping is much less than that on snow. hidden rocks or tree stumps partially Thus, these distances can be multi- hidden by a recent snowfall. plied manyfold. Steering is minimal, and uncontrolled spins are an ever Deep Snow present danger.
  • Page 23 RIDING THE VEHICLE Downhill You should always carry a snow shovel, probe and avalanche beacon while rid- Downhill driving requires that you have ing on mountains. We recommend full control of your vehicle at all times. that all mountain riders take a lo- On steeper hills, keep your center of cal avalanche safety training course gravity low and both hands on the han-...
  • Page 24 RIDING THE VEHICLE Bright Sunshine ahead. Apply partial throttle and brace yourself for the impact. Knees must Bright sunny days can considerably be flexed to act as shock absorbers. reduce your vision. The glare from sun and snow may blind you to the ex- Turning tent that you cannot easily distinguish ravines, ditches or other obstacles.

  • Page 25: Environment

    RIDING THE VEHICLE snowmobile is not designed to oper- It is always IMPORTANT to keep a ate on bare pavement and steering on safe distance between each snowmo- this type of surface is more difficult. bile. Always maintain a safe interval and allow sufficient stopping distance.
  • Page 26 RIDING THE VEHICLE able to introduce others to what they all snowmobilers to remember that re- know and enjoy about their favorite specting the environment is not only winter pastime. So, the next time you critical to the future of our industry but hit the trails on a cool, crisp and clear to future generations.
  • Page 27 So whether you're driving a high perfor- mance Lynx, a sporty RS snowmobile or any other make or model, show you know what you're doing. Show you...

  • Page 28: Traction Enhancing Products

    However, you MUST WARNING only use the BRP approved type stud for use on these Lynx snow- If the front and rear of the snow- mobiles. DO NOT EVER use con- mobile are out of balance due to an...

  • Page 29: Acceleration

    TRACTION ENHANCING PRODUCTS Understeering WARNING In certain conditions, the use of studs To prevent surprises that could on the track could make the snowmo- lead to a loss of control of the bile prone to understeering if the skis snowmobile: are not equipped with more aggressive –...

  • Page 30: Effects Of Having A Studded Track On The Life Of The Snowmobile

    TRACTION ENHANCING PRODUCTS Effects of Having a Installation of Studs on Studded Track on the BRP Approved Tracks Life of the Snowmobile WARNING The use of traction enhancing products can increase the load and the stress on Never stud a track that has not certain snowmobile components, as been approved for studs.

  • Page 31: Maintenance/Replacement

    TRACTION ENHANCING PRODUCTS Maintenance/Replacement WARNING PROCEED WITH A VISUAL INSPEC- – See an authorized Lynx dealer TION OF YOUR TRACK BEFORE for current specific studding EACH USE. availability and applications. Look for any defects, such as: – DO NOT EVER use conventional –...

  • Page 32: Important On-Product Labels

    The following labels are on your vehicle and they should be considered permanent parts of the vehicle. If missing or damaged, the decals can be replaced free of charge. See an authorized Lynx dealer. NOTE: In the event of any discrepancy between this guide and the vehicle, the safety labels on the vehicle have precedence over the labels in this guide.
  • Page 33 IMPORTANT ON-PRODUCT LABELS 516005521 LABEL 4 fmo2015-004-017_a 2 UP MODEL 516006900 en LABEL 5 516006903 LABEL 1 fmo2014-001-017 LABEL 6- SHOCK 516003919 LABEL 2- ON PULLEY GUARD 516005904A LABEL 7 516006900 en LABEL 3 ON PULLEY GUARD _______ ________ SAFETY INFORMATION...
  • Page 34 IMPORTANT ON-PRODUCT LABELS mmo2008-003-007 516004607 LABEL 8 ________ ________ SAFETY INFORMATION...
  • Page 35 IMPORTANT ON-PRODUCT LABELS Label 9 WARNING – Always use a securely fastened rigid tow bar to tow. – Always reduce your speed when towing. – NEVER sit nor exceed maximum load capacity in cargo area. – MAXIMUM REAR LOAD: 15kg (33lbs) –...

  • Page 36: Technical Information Labels

    IMPORTANT ON-PRODUCT LABELS Label 12 - 2 UP MODELS Label 13 WARNING WARNING Beware of rotating track – Read operator’s guide and get acquainted with the instructions before remove seat from the snowmobile. – Make sure seat is securely latched before riding. 516007584 LABEL 13 Technical Information...
  • Page 37 IMPORTANT ON-PRODUCT LABELS 5447012 LABEL 2 fmo2015-004-020_b ACE MODELS 516006904 en LABEL 3 - IN ENGINE COMPARTMENT fmo2015-004-022_b E-TEC MODELS 516004572 LABEL 4 E-TEC MODELS fmo2015-004-013_d 516007588 LABEL 6- ADVENTURE LX 516005503 LABEL 1 516007589 LABEL 6- 49 RANGER _______ ________ SAFETY INFORMATION...
  • Page 38 IMPORTANT ON-PRODUCT LABELS OCTANE mmo2013-002-004 LOCATED ON FUEL CAP 516006447 LABEL ON REAR RACK - ADVENTURE LX ________ ________ SAFETY INFORMATION...
  • Page 39 IMPORTANT ON-PRODUCT LABELS This page is intentionally blank _______ ________ SAFETY INFORMATION...

  • Page 40: Vehicle Information

    VEHICLE INFORMATION _______________...

  • Page 41: Controls, Instruments And Equipment

    CONTROLS, INSTRUMENTS AND EQUIPMENT NOTE: Some features may not apply to your model or could be optional. NOTE: Some vehicle safety labels are not shown on illustrations. For information VEHICLE SAFETY LABELS on vehicle safety labels, refer to subsection. fmo2015-004-031_b TYPICAL ______________...

  • Page 42: Handlebar

    CONTROLS, INSTRUMENTS AND EQUIPMENT fmo2015-004-032_c 1) Handlebar The handlebar controls the steering of the snowmobile. As the handlebar is rotated to right or left, the skis are turned right or left to steer the snow- mobile. WARNING Fast reverse while turning, could fmo2015-004-013_c result in loss of stability and con- trol.
  • Page 43 CONTROLS, INSTRUMENTS AND EQUIPMENT WARNING Test the throttle lever operation each time before starting the en- gine. The lever must return to its the rest position once released. Otherwise, do not start engine. Switching from Thumb to Finger Throttle Position mmo2008-008-011_b TYPICAL CAUTION It is highly recom-...

  • Page 44: Brake Lever

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2015-008-100_a fmo2015-002-001_e IF WANTED, CONTINUE TO ROTATE THE TYPICAL THROTTLE HOUSING 1. Brake lever 2. To apply brake 4) Parking Brake Lever Parking brake lever is located on the LH side of handlebar. Parking brake should be used when- ever snowmobile is parked.

  • Page 45: Engine Cut-Off Switch

    The engine cut-off switch (tether cord) be programmed by your authorized is located to on the RH side of console. Lynx dealer to accept up to 8 different The tether cord cap must be securely keys. snapped on the engine cut-off switch We recommend the purchase of ad- to allow vehicle operation.

  • Page 46: Emergency Engine Stop Switch

    COLOR Normal Gray Learning Green The Lynx learning key, limits the speed of the snowmobile and the engine torque, therefore enabling first time users and less experienced operators to learn how to operate the snowmo- bile while gaining the necessary confi- dence and control.
  • Page 47 CONTROLS, INSTRUMENTS AND EQUIPMENT NOTE: Heated grips or throttle lever are enabled above 1900 engine RPM. All Models Depress switch as required to select heating intensity to keep your hands at a comfortable temperature. Heated Grips Switch mmo2014-004-002_l E-TEC and ACE Models 1.

  • Page 48: Tool Kit

    CONTROLS, INSTRUMENTS AND EQUIPMENT 8) Tool Kit NOTE: Belt guard is purposely made slightly oversize to maintain tension on A tool kit containing tools for basic its pins and retainers preventing undue maintenance is supplied with the vehi- noise and vibration. It is important that cle.

  • Page 49: 10) Gauge

    NOTE: The gauge is factory preset in metric units but it is possible to change it to Imperial units, contact an autho- rized Lynx dealer for unit settings. 1) Speedometer Measures vehicle speed (in miles per hour or kilometers per hour depending on the setting).
  • Page 50 CONTROLS, INSTRUMENTS AND EQUIPMENT 3) Digital Display mmo2014-002-001_b 1. Digital display mmo2014-001-001 The multifunction display is used to: LH PORTION OF GAUGE – Display the WELCOME message on power up 2) Tachometer (RPM) – Display the KEY recognition mes- Measures engine revolution sage...
  • Page 51 B) Trip meter “A” or “B” C) Trip hour meter D) Fuel level NOTE: The display is factory preset in Metric units but it is possible to change it to Imperial units, contact an authorized Lynx dealer for unit settings. ______________...
  • Page 52 CONTROLS, INSTRUMENTS AND EQUIPMENT A) Odometer Records the total distance travelled. Press the SET (S) button to select odometer mode. mmo2014-002-001_c C) Trip Hour Meter Records vehicle running time when the electrical system is activated since it has been reset. Press the SET (S) button to select trip mmo2014-002-001_d hour meter (HrTRIP) mode.

  • Page 53: Analog/Digital Gauge (Standard)

    Unit Selection (KM/H vs MPH) the digital display. The units can be set in metric or imperi- NOTE: There are nine intensity set- als. Refer to an authorized Lynx dealer. tings. When released, display will re- turn to fuel tank level. 11) Analog/Digital Gauge...
  • Page 54 NOTE: The gauge is factory preset in 3) Digital Display metric units but it is possible to change it to Imperial units, contact an autho- rized Lynx dealer for unit settings. 1) Speedometer Measures vehicle speed (in miles per hour or kilometers per hour depending on the setting).
  • Page 55 Opt = Feature available as an option N.A. = Not available (1) Coolant temperature is an option package. See a Lynx dealer for more information NOTE: The display is factory preset in Metric units but it is possible to change it to Imperial units, contact an autho- rized Lynx dealer for unit settings.
  • Page 56 CONTROLS, INSTRUMENTS AND EQUIPMENT A) Odometer C) Trip Hour Meter Records the total distance travelled. Records vehicle running time when the electrical system is activated since Press the SET (S) button to select it has been reset. odometer mode. Press the SET (S) button to select trip hour meter (HrTRIP) mode.

  • Page 57: Multifunction Analog/Digital Gauge

    OPTIONAL MODULE INSTALLED metric units but it is possible to change 1. Overheating indicator it to Imperial units, contact an autho- rized Lynx dealer for unit settings. F) E-TEC Engine Storage Mode Displays "OIL" when the engine enters 1) Speedometer the storage procedure.
  • Page 58 CONTROLS, INSTRUMENTS AND EQUIPMENT 4) Pilot Lamps and Messages mmo2008-003-024_a TYPICAL — PILOT LAMPS mmo2008-007-018 RH PORTION OF GAUGE 3) Multifunction Digital Display mmo2007-009-066_u MULTIFUNCTION ANALOG/DIGITAL GAUGE 1. Multifunction display The multifunction display is used to: – Display the WELCOME message on power up –...
  • Page 59 CONTROLS, INSTRUMENTS AND EQUIPMENT MONITORING SYS- See table below for usual pilot lamps information. Refer to for details on malfunction pilot lamps. PILOT LAMP(S) BEEPER MESSAGE DISPLAY DESCRIPTION 4 short beeps E-TEC: Injection oil level is low. Stop vehicle in a safe LOW OIL every place then, replenish injection oil reservoir.
  • Page 60 CONTROLS, INSTRUMENTS AND EQUIPMENT Gauge Features GAUGE FEATURES FUNCTIONS 600 HO E-TEC A) Speedometer Indication by default B) Engine RPM C) Odometer D) Trip meter “A” or “B” E) Trip hour meter F) Clock G) Fuel level H) Altitude I) Top speed J) Average speed K) Heated grips heating intensity L) Heated throttle lever heating intensity...
  • Page 61 CONTROLS, INSTRUMENTS AND EQUIPMENT A) Speedometer Press the MODE (M) button to confirm selection or wait 5 seconds. addition analog type speedometer, vehicle speed can also be displayed via the multifunction display. Vehicle speed can be displayed on dis- play 1 or display 2. mmo2007-009-066_o B) Tachometer (RPM) In addition of the analog type tachome-...

  • Page 62: C) Odometer

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_n mmo2007-009-066_p 1. RPM mode 1. Trip meter (TRIP A/TRIP B) mode Press the MODE (M) button to confirm Press and hold the SET (S) button to re- selection or wait 5 seconds. set. NOTE: On E-TEC models, resetting TRIP B mode will also reset TOTAL FUEL CONSUMPTION.

  • Page 63: F) Clock

    CONTROLS, INSTRUMENTS AND EQUIPMENT To change MINUTES, while the value of HOURS is blinking, press the MODE (M) button to switch to minutes. Use the SET (S) button to change minutes. Press the MODE (M) button to save clock set-up and exit mode. G) Fuel Level Bar gauge that continuously indicates mmo2007-009-066_k...

  • Page 64: I) Top Speed

    CONTROLS, INSTRUMENTS AND EQUIPMENT While display is flashing, press the SET (S) button to select altitude mode. mmo2007-009-066_m While display flashes, press the SET (S) button to select top speed (TOP_SPD) mode. mmo2007-009-066_k The following symbol appears when al- titude mode is selected. mmo2008-003-023 ALTITUDE MODE mmo2007-009-066_n...

  • Page 65: J) Average Speed

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_m mmo2007-009-066_n 1. Vehicle average speed (AVR_SPD) mode While display flashes, press and hold the SET (S) button within 5 seconds to Press the MODE (M) button to confirm reset. selection or wait 5 seconds. mmo2007-009-066_w mmo2007-009-066_o J) Average Speed To reset, press the MODE (M) to select...

  • Page 66: K) Heated Grips Heating Intensity

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_w K) Heated Grips Heating Intensity mmo2007-009-044_a HEATED THROTTLE LEVER Bar gauge that indicates heating inten- 1. Operating range sity. M) Instant Fuel Consumption HEATED GRIPS SWITCH Refer to more details. Calculates vehicle average fuel con- sumption while riding.

  • Page 67: N) Total Fuel Consumption (Ace)

    CONTROLS, INSTRUMENTS AND EQUIPMENT Press the MODE (M) button to confirm TC appears when the mode is se- selection or wait 5 seconds. lected. mmo2008-003-021_a TYPICAL mmo2007-009-066_o Press the MODE (M) button to confirm N) Total Fuel Consumption selection or wait 5 seconds. Records vehicle average fuel con- sumption since it has been reset.

  • Page 68: O) Message Display

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2012-006-902_a mmo2007-009-066_w Q) E-TEC Engine Storage Mode O) Message Display Displays "OIL" when the storage mode procedure is initiated. R) Lap Record Mode With this mode, vehicle speed, engine revolutions per minute (RPM) and a preselected function in display 1 can be recorded at the same time during a period of time defined by the operator.
  • Page 69 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2009-009-002_a 1. Record mode mmo2009-009-003_a 2. Odometer RECORD MODE 1. Recording time 3. Press the SET (S) button to scroll be- 2. Lap/session 3. Selected mode tween modes. Available modes are: STOP, REC To record another session, press the (record) or PLAY.

  • Page 70: Eco/Standard/Sport Mode Switch

    Press and hold SET (S) button for 5 sec- The units can be set in metric or imperi- onds to exit the lap record mode, the als. Refer to an authorized Lynx dealer. previously selected mode will be dis- played.

  • Page 71: 15) Shift Lever

    CONTROLS, INSTRUMENTS AND EQUIPMENT 17) Upper Body Module (Hood) Upper Body Module Removal 1. Remove the gauge. mmo2013-004-017_a 1. Tab 2. Storage compartment 15) Shift Lever Use this lever to shift in forward or re- verse. mbl2012-008-001_a Step 1: Unlock Step 2: Tilt 2.
  • Page 72 CONTROLS, INSTRUMENTS AND EQUIPMENT ACE Models 9. Pull backward the air intake tube. mmr2008-010-004_a Step 1: Lift tab Step 2: Twist tube Step 3: Pull forward 7. Disconnect air temperature sensor (ATS) on top of connector tube. fmo2014-002-034_a 1. Air intake tube All Models 10.
  • Page 73 CONTROLS, INSTRUMENTS AND EQUIPMENT fmo2014-002-008_a fmo2014-002-008_b SLIDE TOWARDS FRONT SLIDE TOWARDS REAR 3. On both sides, install the upper body Upper Body Module Installation module retaining screws. 1. Insert the upper body module tabs into the upper bottom pan open- ings.

  • Page 74: 18) Side Panels

    CONTROLS, INSTRUMENTS AND EQUIPMENT All Models 6. Install: – Gauge – Drive belt guard. 18) Side Panels To open a side panel, push the buttons. fmo2014-002-006_a 1. Upper hinge 2. Lower hinge Close the side panel. fmo2015-004-021_c TYPICAL 1. Buttons To close a side panel, set firmly on the stud location and push side panel locks to make sure it is secured.

  • Page 75: 20) Rear Rack

    CONTROLS, INSTRUMENTS AND EQUIPMENT 20) Rear Rack 2. Open The LINQ Attachments. 3. Lift the backrest. WARNING All objects in rear rack must be properly latched. Do not carry any breakable objects. Excessive weight in rack may reduce steering ability. Always readjust suspen- sion according to the load.
  • Page 76 CONTROLS, INSTRUMENTS AND EQUIPMENT fsi2013-010-003_b fsi2013-010-001 Attach the battery cover back to its Remove the seat by pulling and lifting place. at the same time. fsi2013-010-005 fsi2013-010-002 NOTICE Pull the handle upwards Finish the installation by locking the when removing the seat. storage / battery compartment cover.

  • Page 77: Storage/Battery Compartment

    CONTROLS, INSTRUMENTS AND EQUIPMENT 23) Storage/Battery Hitch ("J" Type) Compartment 49 Ranger Models NOTICE MAXIMUM load is 1.8 kg (4 lb) evenly distributed. Turn quarter-turn fastener counter- clockwise to release it and open cover. mmo2011-007-012_a 1. Hairpin clip 2. Safety tab Attaching an Equipment 1.

  • Page 78: Fuel

    FUEL Fuel Requirements MINIMUM FUEL TYPE ENGINE OCTANE NOTICE Always use fresh gaso- RATING line. Gasoline will oxidize; the re- Fuel which sult is loss of octane, volatile com- may contain 600 HO pounds, and the production of gum up to 95 E10 E-TEC and varnish deposits which can...
  • Page 79 FUEL 6. Stop filling when the fuel reaches WARNING the bottom of filler neck. Do not Always stop engine before refuel- overfill. ing. WARNING 2. Have operator and passenger get Never top up the fuel tank before off vehicle. placing the vehicle in a warm area. As temperature increases, fuel ex- WARNING pands and may overflow.

  • Page 80: Injection Oil (E-Tec)

    INJECTION OIL (E-TEC) Recommended Injection E-TEC Models RECOMMENDED INJECTION OIL XPS SYNTHETIC 2-STROKE OIL(F) ENGINES (P/N 619 590 106) 600 HO E-TEC NOTICE The engine of this snowmobile has been developed and validated using the recommended BRP XPS™ oil. BRP recommends the use of its rec- ommended XPS oil or equivalent.

  • Page 81: Break-In Period

    – The fuel and oil consumption will be higher. After the break-in period, the vehicle should be inspected by an authorized Drive Belt Lynx dealer, repair shop or person of MAINTE- your own choosing. Refer to A new drive belt requires a break in pe- NANCE section.

  • Page 82: Operating Modes (Ace)

    OPERATING MODES (ACE) To increase power, press the switch WARNING upwards. To decrease power, press Whenever changing operating the switch downwards. mode, make sure to maintain situ- ational awareness while riding. ECO Mode (Fuel Economy Mode) When ECO mode is selected (fuel economy mode), vehicle torque and speed are limited whereby an optimal cruising speed is maintained in order...

  • Page 83: Learning Key Modes

    70 km/h All Models (43 MPH). Refer to your authorized 5. Use the heated grip switch to toggle Lynx dealer to modify this setting. the key setting between 1 and 3. There are 3 levels available for the learning key mode.
  • Page 84 OPERATING MODES (ACE) fmo2015-002-001_a TYPICAL 1. Heated grip switch 2. Increase 3. Decrease NOTE: Setting 1 is the lowest avail- able torque, while setting 3 is the high- est available torque for learning key. 6. After a few seconds, the setting is automatically confirmed and saved.

  • Page 85: Basic Procedures

    BASIC PROCEDURES Engine Starting Procedure CAUTION Do not use electric starter for more than 10 seconds. A Procedure rest period should be observed be- tween the cranking cycles to let elec- 1. Apply parking brake. tric starter cool down. Using elec- 2.

  • Page 86: Vehicle Warm-Up

    BASIC PROCEDURES WARNING Do not wind starting rope around your hand. Hold rope by the han- dle only. Do not start the snowmo- bile by the drive pulley unless it is a true emergency situation. Have the snowmobile repaired as soon as possible.

  • Page 87: Engaging Reverse (Rer) (E-Tec)

    BASIC PROCEDURES Engaging Reverse (RER) 2. Allow engine to warm up one or two minutes at idle speed. (E-TEC) NOTE: E-TEC engines will shut down When the engine is running, depress- after approximately 12 minutes of ing the RER button will slow down en- idling.

  • Page 88: Shifting In Reverse Or Forward (Ace Models)

    BASIC PROCEDURES Shifting in Forward 2. Apply and hold brake. 1. Bring vehicle to a complete stop. 3. With engine at idle speed, push the reverse shift lever all the way in. 2. Apply and hold brake. 4. Gently depress throttle lever. 3.

  • Page 89: Riding Conditions And Your Snowmobile

    (2,000 ft) If your snowmobile is to be used at an altitude outside the specified range, have it calibrated accordingly by an au- thorized Lynx dealer. NOTICE An inappropriate altitude calibration would decrease perfor- mance and may cause serious dam- age to the snowmobile.

  • Page 90: Special Operation

    SPECIAL OPERATION Towing an Accessory Always use a rigid tow bar to tow an ac- cessory. Any towed accessory should have reflectors on both sides and at the rear. Check local laws for brake light(s) requirements. WARNING Never tow an accessory with a rope.

  • Page 91: Tune Your Ride

    TUNE YOUR RIDE Snowmobile handling and comfort de- are interrelated. It may be necessary pend upon multiple adjustments. to readjust center spring after adjust- ing front springs for instance. Test run the snowmobile under the same con- WARNING ditions; trail, speed, snow, operator Suspension adjustment could af- riding position, etc.
  • Page 92 TUNE YOUR RIDE Center Spring ACTION RESULT Center spring preload has an effect on Lighter ski pressure steering effort, handling and bump ab- under acceleration sorption. Increasing stopper More center spring travel Also, since center spring preload ad- strap length justment puts more or less pressure More bump absorption on the front of the track, it has an ef-...
  • Page 93 NOTE: If the specification is unattain- Lighter steering able with the original springs, see an Better deep snow authorized Lynx dealer for other avail- able springs. performance and handling Rear Suspension Extension Spring Refer to the following to determine if Preload preload is correct.

  • Page 94: Front Suspension Adjustments

    TUNE YOUR RIDE ACTION RESULT CAM SETTING RESULT More track surface on Locks the Increasing the ground suspension preload extension in Less extension lift line with the suspension rails Better reverse capability Leaning on stop Decreasing especially in deep snow block Better traction, preload...
  • Page 95 TUNE YOUR RIDE NOTE: Make sure your vehicle does not exceed the maximum width al- lowed for trail riding. Check local regu- lations. Front Springs Front spring preload has an effect on front suspension firmness. Front spring preload also has an effect on the steering behavior.

  • Page 96: Adjustment Tips According To Vehicle Behavior

    TUNE YOUR RIDE Adjustment Tips According to Vehicle Behavior PROBLEM CORRECTIVE MEASURES Check ski alignment. – Reduce front suspension spring preload. Front suspension darting – Increase center spring preload. – Reduce rear spring preload. Steering feels too heavy at steady –...

  • Page 97: Vehicle Transportation

    VEHICLE TRANSPORTATION Make sure the fuel tank cap is properly installed. Tilt bed trailers can easily be equipped with a winch mechanism to afford ma- ximum safety in loading. Simple as it may seem, never drive your snowmo- bile onto a tilt bed trailer or any other kind of trailer or vehicle.

  • Page 98: Maintenance

    MAINTENANCE _______________...

  • Page 99: First Inspection

    After the first 10 hours or 500 km (300 mi) of operation, whichever comes first, your vehicle have to be inspected by an authorized Lynx dealer, repair shop or person of your own choosing. The first inspection is very important and must not be neglected.
  • Page 100 FIRST INSPECTION FIRST INSPECTION (4-STROKE) AFTER THE FIRST 500 KM (300 MI) OR 10 HOURS OF OPERATION, WHICHEVER COMES FIRST Inspect engine seals and gaskets for leaks Inspect exhaust system and check for leaks ENGINE Check coolant level FUEL Inspect fuel lines and connections SYSTEM Inspect drive belt Visually inspect drive pulley...

  • Page 101: Maintenance Schedule (E-Tec)

    MAINTENANCE SCHEDULE (E-TEC) NOTE: The maintenance schedule does not exempt the pre-ride inspection. WARNING Failure to properly maintain the vehicle according to the maintenance schedule and procedures can make it unsafe to operate. EVERY 1 500 KM (1,000 MI) Models with chaincase: Adjust drive chain DRIVE Models with chaincase: Check chaincase oil level SYSTEM...
  • Page 102 MAINTENANCE SCHEDULE (E-TEC) EVERY 6 000 KM (4,000 MI) OR 2 YEARS (WHICHEVER COMES FIRST) Clean and lubricate rewind starter ENGINE Inspect fuel pump strainer and replace if necessary FUEL SYSTEM Inspect throttle cable Replace brake fluid DRIVE Replace the following drive pulley wear parts: slider shoes, O-rings SYSTEM and sliding sheave bushing (E-TEC) SUSPENSION...

  • Page 103: Maintenance Schedule (Ace)

    MAINTENANCE SCHEDULE (ACE) NOTE: The maintenance schedule does not exempt the pre-ride inspection. WARNING Failure to properly maintain the vehicle according to the maintenance schedule and procedures can make it unsafe to operate. EVERY 1 500 KM (1,000 MI) Models with chaincase: Adjust drive chain DRIVE Models with chaincase: Check chaincase oil level SYSTEM...
  • Page 104 MAINTENANCE SCHEDULE (ACE) EVERY 6 000 KM (4,000 MI) OR AT PRE-SEASON (WHICHEVER COMES FIRST) Change engine oil and filter ENGINE EVERY 6 000 KM (4,000 MI) OR 2 YEARS (WHICHEVER COMES FIRST) Replace fuel filter FUEL SYSTEM Replace fuel pump outlet filter (ACE) Replace drive pulley slider shoes, O-ring and rollers and inspect ramps DRIVE (900 ACE)

  • Page 105: Maintenance Procedures

    If additional coolant is necessary or if entire system has to be refilled, refer to Air Filter with Dual Air an authorized Lynx dealer, repair shop Intake or person of your own choosing. Air Filter Verification There are two air intake pre-filters, one on each side of the console.

  • Page 106: Engine Oil

    MAINTENANCE PROCEDURES ACE Models Recommended Engine Coolant RECOMMENDED COOLANT ENGINE ENGINE OIL LONG LIFE XPS 4-STROKE 600 and ANTIFREEZE(F) recommended SYNTHETIC OIL (F) 900 ACE product (P/N 619 590 204) (P/N 619 590 114) Distilled water and NOTICE The engine of this snow- Alternative, or antifreeze solution mobile has been developed and val-...
  • Page 107 MAINTENANCE PROCEDURES 5. Remove dipstick from the filler tube, then wipe it clean. 6. Completely insert dipstick in the filler tube. 7. Remove dipstick and check the oil level. Oil level should be be- tween the MIN. and MAX. marks as shown, add if necessary.

  • Page 108: Engine Oil Filter (Ace)

    MAINTENANCE PROCEDURES 6. Place a drain pan under the bottom TIGHTENING TORQUE pan opening. 15 N•m ± 1.8 N•m Drain plugs 7. Remove engine drain plugs in the (133 lbf•in ± 16 lbf•in) following order. 7.1 Main drain plug. OIL FILTER 11.

  • Page 109: Engine Stopper (E-Tec)

    MAINTENANCE PROCEDURES mmr2011-070-009_a 1. Lubricate with engine oil mmr2011-070-007_a 4. Install the oil filter cover. 1. Oil filter cover screws 2. Oil filter cover 5. Tighten oil filter cover screws to the 3. O-ring specified torque. 4. Oil filter TIGHTENING TORQUE 4.

  • Page 110: Exhaust System

    MAINTENANCE PROCEDURES mmo2010-009-002_a 1. Rubber stop block mmo2010-009-007_a 2. Bump 1. Drive pulley 3. Feeler gauge 2. Engine stopper screws 3. Engine stopper 7. Tighten screws to 10 N•m ± 2 N•m (89 lbf•in ± 18 lbf•in) following the 5. Insert a 0.5 mm (.02 in) feeler gauge illustrated sequence, taking care not in the engine stopper opening (see to pinch the feeler gauge.

  • Page 111: Spark Plugs

    (P/N 529 035 983) Spark Plugs Spark plugs inspection or replacement may be performed by an authorized Lynx dealer, repair shop, or person of your own choosing. Spark plugs in- spection or replacement requires an 529035983 in-depth technical knowledge. Though...

  • Page 112: Chaincase Oil

    MAINTENANCE PROCEDURES Chaincase Oil NOTICE Brake fluid can damage painted and plastic parts. Handle with care. Rinse thoroughly in case Recommended Chaincase Oil of spillage. RECOMMENDED CHAINCASE OIL Brake Fluid Level Verification (P/N 619 590 098) Place vehicle on a level surface. Check brake fluid in reservoir for proper NOTICE The chaincase of this...

  • Page 113: Drive Chain

    MAINTENANCE PROCEDURES ACE Models Oil level must reach the threaded hole. mmo2011-003-017_a TYPICAL 1. Check plug mmo2011-003-017_a TYPICAL 1. Check plug All Models Oil level must reach the threaded hole. Chaincase Filling Procedure Remove the check plug. Remove the filler cap on the chaincase mbs2010-019-001_a cover.

  • Page 114: Drive Belt

    2. Unscrew tensioner lock nut several riod, burred or rusty sheave, oil on drive turns. belt or distorted spare drive belt. Con- tact an authorized Lynx dealer. Drive Belt Replacement Drive Belt Removal 1. Remove tether cord cap from en- gine cut-off switch.
  • Page 115 MAINTENANCE PROCEDURES NOTE: The maximum drive belt life 4. Using the suspension adjustment span is obtained when drive belt is in- tool provided in the tool kit, turn stalled with arrows in the direction of the ring 1/4 turn at a time then ro- rotation.

  • Page 116: Drive Pulley (E-Tec)

    MAINTENANCE PROCEDURES If the vehicle creeps, lower the drive belt height from the preliminary set- ting. Repeat procedure until creeping stops. Reverse Activation NOTE: The reverse may not activate or may be harder to activate if the drive mmo2012-006-905_a belt is positioned too high in the driven TYPICAL - PRELIMINARY SETTING pulley.
  • Page 117 200 RPM. speed. Example: See your Lynx dealer to maintain Calibration screws initially set at posi- or service the drive pulley. Im- tion 4 and changed to position 6 will proper servicing or maintenance...

  • Page 118: Track

    Track Tension Verification authorized Lynx dealer. NOTE: Ride the snowmobile in snow Snowmobiles Equipped with about 15 to 20 minutes prior to adjust- Traction Enhancing Products ing track tension.
  • Page 119 MAINTENANCE PROCEDURES FICATIONS at the end of this guide. If the track tension is too loose, track will have a tendency to thump. mmr2009-133-003_a LOAD READING 1. Upper O-ring 10. Load reading must be as per the SPECIFICA- following table / see mmr2009-133-003_b TIONS at the end of this guide.
  • Page 120 1. RH rear idler wheel bolt between edges of track guides and 2. RH adjustment screw slider shoes. 5. If correct tension is unattainable, contact an authorized Lynx dealer. 6. Retighten retaining bolts to specifi- cation. TIGHTENING TORQUE 48 N•m ± 6 N•m Retaining Bolt (35 lbf•ft ±...

  • Page 121: Suspension

    MAINTENANCE PROCEDURES Suspension Rear Suspension Condition Visually inspect all suspension compo- nents including slider shoes, springs, wheels, etc. NOTE: During normal driving, snow A01F0BA will act as a lubricant and coolant for 1. Guides the slider shoes. Extensive riding on 2.

  • Page 122: Skis

    If fuse has burnt out, source of mal- etc.). If necessary, contact an autho- function should be determined rized Lynx dealer. and corrected before restarting. See an authorized Lynx dealer for Skis servicing. Wear and Condition of Skis and Fuse Location...

  • Page 123: Lights

    MAINTENANCE PROCEDURES E-TEC Electric Start mmo2007-009-016_b BEHIND AIR INTAKE SILENCER 1. Fuse location - 0.25 A fuse Lights Always check light operation after bulb replacement. fmr2014-001-021_a RH SIDE OF ENGINE COMPARTMENT Headlights Bulb Replacement 1. Charging fuse 2. START/RER fuse NOTICE Never touch glass portion 600 ACE and 900 ACE...
  • Page 124 MAINTENANCE PROCEDURES mmo2013-004-036_c mmo2013-004-020_a Step 1: Push both sides 1. Rubber boots Step 2: Push down to release Step 3: Release both sides NOTE: Make sure to properly reinstall 1. Retaining clip both rubber boots to ensure that no hu- 5.

  • Page 125: Vehicle Care

    VEHICLE CARE Post-Operation Care NOTE: Apply wax on glossy finish only. Remove snow and ice from rear sus- pension, track, front suspension, steering mechanism and skis. WARNING Make sure tether cord cap is away from engine cut-off switch before standing in front the vehicle, get- ting close to the track or rear sus- pension components.

  • Page 126: Storage

    The antifreeze replacement and a den- 1. Place the vehicle in a well ventilated sity test should be performed by an au- area. thorized LYNX dealer. 2. Start the engine and let it run at idle speed until it reaches its operat- CAUTION Improper antifreeze...
  • Page 127 STORAGE mmr2009-004-002 mmr2009-004-004 NOTE: The storage mode does not Do not touch anything during engine lu- function in other modes (trip A, trip B brication cycle. and hr trip). The engine lubrication function takes 4. Repeatedly depress the HI/LOW approximately 1 minute. During this beam switch rapidly, then, while time the engine RPM will increase doing this, press and hold the SET...

  • Page 128: Preseason Preparation

    PRESEASON PREPARATION PRESEASON PREPARATION (2-STROKE) Inspect engine rubber mounts Check exhaust system condition and check for leaks Tighten exhaust manifold screws or nuts to specified torque ENGINE Inspect cooling system cap, hoses and clamps and check for leaks Check coolant density Inspect crankshaft PTO seal Inspect fuel lines and connections FUEL...
  • Page 129 PRESEASON PREPARATION PRESEASON PREPARATION (4-STROKE) Visually inspect engine seals and gaskets and check for leaks Check exhaust system condition and check for leaks ENGINE Change engine oil and filter Check coolant density Inspect fuel lines and connections FUEL SYSTEM Clean and inspect throttle body Inspect drive belt (adjust at every drive belt replacement) Clean and visually inspect drive pulley Clean and inspect driven pulley...

  • Page 130: Technical Information

    TECHNICAL INFORMATION ______________...

  • Page 131: Vehicle Identification

    ENGINE COMPARTMENT snowmobile in the event of loss. 1. Engine serial number These numbers are required by the authorized Lynx dealer to complete warranty claims properly. We strongly recommend that you take note of all the identification numbers on your snowmobile and supply them to your insurance company.
  • Page 132 VEHICLE IDENTIFICATION mmo2011-003-003_a 600 ACE ENGINE 1. Engine identification number mmo2014-004-007_a 900 ACE ENGINE 1. Engine identification number ______________...

  • Page 133: Noise Emission And Vibration Values

    NOISE EMISSION AND VIBRATION VALUES (ALL COUNTRIES EXCEPT CANADA/UNITED STATES) MODEL 600 HO E-TEC 600 ACE 900 ACE NOISE EMISSION AND VIBRATION VALUES 96,7 dB @ 4050 90,4 dB @ 3625 92,7 dB @ 3625 Sound power level RPM (Uncertainty RPM (Uncertainty RPM (Uncertainty ) 3 dB)

  • Page 134: Ec Declaration Of Conformity

    The EC-Declaration of Conformity does not appear in this version of the Operator's Guide. Please refer to the printed version that was delivered with your vehicle. ddd2009-001...

  • Page 135: Radio Frequency Digitally Encoded Security System

    RADIO FREQUENCY DIGITALLY ENCODED SECURITY SYSTEM (RF D.E.S.S. KEY) This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

  • Page 136: Specifications

    SPECIFICATIONS MODEL 600 ACE ENGINE Rotax 602, liquid cooled, 4-stroke, Engine type D.O.H.C., dry sump Cylinders Displacement 600 cm³ (36.6 in³) Bore 74 mm (2.9 in) Stroke 69.7 mm (2.74 in) Maximum horsepower RPM 7250 RPM Exhaust system Double front pipe, baffle muffler XPS 4-STROKE SYNTHETIC OIL (F) (P/N 619 Engine oil 590 114)
  • Page 137 SPECIFICATIONS MODEL 600 ACE ELECTRICAL SYSTEM (cont'd)) FA: Main 40 A F1: Fuel/engine 10 A F2: Accessories 20 A F3: Fan 15 A F4: Start 15 A Fuses and relays F5: Lighting 20 A F6: Gauge/ECM/CAPS 10 A R1: Fuses 1, 6 R2: Fuse 5 R3: Fuse 2 DRIVE SYSTEM...
  • Page 138 SPECIFICATIONS MODEL 600 ACE DRIVE SYSTEM (cont'd) Adventure LX with Silent Drive 38 cm (14.961 in) Track nominal width All others 40.6 cm (15.984 in) Adventure LX 348.7 cm (137.283 in) Track nominal length 49 Ranger 414.1 cm (163.031 in) 49 Ranger 39 mm (1.535 in) Adventure LX except Silent...
  • Page 139 921 mm ± 21 mm (36.26 in ± .827 in) 49 Ranger Touring 996 mm ± 21 mm (39.213 in ± .827 in) Drive belt height must be adjusted every time a new drive belt is installed. Confirm drive belt part number application with an authorized LYNX dealer. ______________...
  • Page 140 SPECIFICATIONS 600 HO E-TEC Models MODEL 600 HO E-TEC ENGINE Engine type Rotax 593, liquid cooled w/Reed valve, 3D-RAVE Cylinders Displacement 594.4 cm³ (36.3 in³) Bore 72 mm (2.8 in) Stroke 73 mm (2.9 in) Maximum engine speed 8100 ± 100 RPM Fuel injection system E-TEC Direct injection Exhaust system...
  • Page 141 SPECIFICATIONS MODEL 600 HO E-TEC DRIVE SYSTEM (cont'd) Track nominal width 40.6 cm (15.984 in) Track nominal length 414.1 cm (163.031 in) Track profile height 59 mm (2.323 in) Deflection 40 mm - 50 mm (1.575 in - 1.969 in) Track tension Force 0 kg (0 lb)
  • Page 142 SPECIFICATIONS MODEL 600 HO E-TEC DIMENSIONS AND WEIGHT Vehicle overall length 347 cm (136.6 in) 49 Ranger 110.5 cm (43.5 in) Vehicle overall width 49 Ranger Touring 118 cm (46.46 in) Vehicle overall height 147 cm (57.874 in) 49 Ranger 257 kg (566.6 lb) Dry weight 49 Ranger Touring...
  • Page 143 SPECIFICATIONS 900 ACE Models MODEL 49 RANGER 900 ACE ENGINE Rotax 903, liquid cooled, 4-stroke, Engine type D.O.H.C., dry sump Cylinders Displacement 899 cm³ (54.9 in³) Bore 74 mm (2.9 in) Stroke 69.7 mm (2.74 in) Maximum horsepower RPM 7250 RPM Exhaust system Single front pipe, baffle muffler (P/N )
  • Page 144 SPECIFICATIONS MODEL 49 RANGER 900 ACE ELECTRICAL SYSTEM (cont'd) FA: Main 40 A F1: Ignition coils, fuel injectors, 10 A fuel pump, starter solenoid F2: Accessories 20 A F3: Electro mechanical reverse 20 A F4: Start clock, cooling fan 10 A Fuses and relays F5: Headlights, taillight, brake 20 A...
  • Page 145 147 cm (57.874 in) Ski stance 996 mm ± 21 mm (39.213 in ± .827 in) Drive belt height must be adjusted every time a new drive belt is installed. Confirm drive belt part number application with an authorized LYNX dealer. ______________...

  • Page 146: Troubleshooting

    TROUBLESHOOTING ______________...

  • Page 147: Troubleshooting Guidelines (E-Tec And Ace)

    (fast short beeps/repetitive). – Install a tether cord cap for which this snowmobile was programmed. 3. ECM does not recognize the D.E.S.S. key (ACE). – Refer to an authorized Lynx dealer. ENGINE LACKS ACCELERATION OR POWER 1. Learning key used (ACE).
  • Page 148 – See MAINTENANCE and/or an authorized Lynx dealer for proper alignment and tension adjustments. 10. R .A.V.E. valves problem. – Seek service from an authorized Lynx dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement. 11. F uel pressure too low.
  • Page 149 TROUBLESHOOTING GUIDELINES (E-TEC AND ACE) HEATED GRIPS/THUMB WARMERS ARE NOT WORKING 1. Engine RPM is too low. – Make sure engine RPM is above 2000 (ACE). ENGINE HAS SHUT DOWN 1. The engine shuts down after long periods of idling. –...

  • Page 150: Monitoring System

    MONITORING SYSTEM Pilot Lamps, Messages and Beeper Codes Gauge pilot lamp(s) will inform you if an anomaly occurs or to inform you of a particular condition. mmo2014-002-003_a TYPICAL — PILOT LAMPS Pilot lamp can flash alone or in combi- nation with another lamp. On the multifunction analog/digital gauge, the display is used as a comple- ment of the pilot lamps to give you a...
  • Page 151 Stop engine rapidly OVERHEAT immediately and let engine cool down. If overheating persists, contact an authorized Lynx dealer. Do not run the engine if condition ECM OVERHEAT persists. Do not run the engine if condition persists. 4 short LOW BAT...
  • Page 152 — SHUTDOWN repeating tether cord cap from engine cut-off switch rapidly and contact an authorized Lynx dealer. Communication problem between ECM and gauge. Stop engine, remove tether cord cap. — — COMMUNICATION Wait a few minutes, then start engine. If...

  • Page 153: Fault Codes

    HI/LOW beam switch repeatedly several times. If two or more codes are registered, use SET (S) or MODE (M) to scroll. To exit the fault codes mode, press and hold MODE (M) button. Contact an authorized Lynx dealer for code signification. ______________...

  • Page 154: Warranty

    WARRANTY ______________...

  • Page 155: Brp Finland Oy International Limited Warranty: 2018 Lynx

    1) SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. (“BRP”)* warrants its 2018 LYNX snowmobiles sold by distributors or dealers authorized by BRP to distribute LYNX snowmobiles ("LYNX Distributor/Dealer") from defects in material or workmanship for the period and under the conditions described below.
  • Page 156 LYNX Distributor/Dealer; – Damage caused by abuse, abnormal use, neglect, racing or operation of the product on surfaces other than snow, or operation of the product in a manner inconsistent with the recommended operation described in the Operator’s...
  • Page 157 This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2018 LYNX snowmobile must be purchased as new and unused by its first owner from a LYNX Distributor/Dealer authorized to distribute LYNX snowmo- biles in the country in which the sale occurred;...
  • Page 158 BRP or an authorized LYNX Distributor/Dealer receives a proof that the former owner agreed to the transfer of ownership, in addition to the co-ordinates of the new owner.
  • Page 159 ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be responsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished under its responsibility.

  • Page 160: Maintenance Records

    MAINTENANCE RECORDS Send photocopy of maintenance record to BRP if needed. PREDELIVERY Serial number: Signature/Print: Mileage / km: Hours: Date: Dealer no: Notes: Refer to vehicle Pre-Delivery Bulletin for detailed installation procedures FIRST INSPECTION Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide...
  • Page 161 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print:...
  • Page 162 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print:...
  • Page 163 This page is intentionally blank ______________...

  • Page 164: Customer Information

    CUSTOMER INFORMATION ______________...

  • Page 165: Contact Us

    CONTACT US North America www.brp.com 565 de la Montagne Street Europe Valcourt (Québec) J0E 2L0 Canada Skaldenstraat 125 B-9042 Gent Sturtevant, Wisconsin, U.S.A. Belgium 10101 Science Drive Sturtevant, Wisconsin Itterpark 11 53177 D-40724 Hilden U.S.A. Germany Sa De Cv, Av. Ferrocarril 202 ARTEPARC Bâtiment B Parque Ind.

  • Page 166: Change Of Address/Ownership

    It is the owner’s responsibility to notify BRP. STOLEN UNITS: If your personal Snowmobile is stolen, you should notify BRP or an authorized Lynx dealer. We will ask you to provide your name, address, phone number, the vehicle identification number and the date it was stolen.
  • Page 167 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 168 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 169 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 170 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 171 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 172 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 173 619 900 938 OPERATOR’S GUIDE, REX TOURING / UTILITY/ ENGLISH GUIDE DU CONDUCTEUR, REX TOURING / UTILITY / ANGLAIS FAIT AU / MADE IN CANADA U/M:P.C. ®™ AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC. OR ITS AFFILIATES. ©2017 BOMBARDIER RECREATIONAL PRODUCTS INC.

This manual is also suitable for:

Brp rex2 49 ranger 600ho e-tecBrp rex2 49 ranger 600ho e-tec touringBrp rex2 49 ranger 600 aceBrp rex2 49 ranger 600 ace touringBrp rex2 49 ranger st 900 ace

Table of Contents