Rigid Industries E Series Product Instructions page 2

Congratulations on your purchase of Rigid Lights!
Insert mounting brackets onto light as shown in Diagram
1.
A or B. Secure hardware to a snug position and mount
your light into desired location. The 4", 6" & 10" E-Series
and 6" & 10" SR-Series light bars include bolts that slide
into each side of light housing before compression
spacers and brackets are attached for mounting.
Disconnect the negative battery cable from the battery.
2.
Attach red terminal eyelet to battery positive or any
3.
12V DC source. Secure black terminal to suitable ground
or battery negative. Route harness to desired switch and
mounting locations, secure with zip ties. Beware of sharp
edges, abrasive surfaces and heat sources when wiring.
When installing Rigid lights on a 24V DC system be
4.
sure to use a 24V relay. When installing multiple lights
be sure to have adequate fusing.
5. Finally, test lights to ensure proper function and then
secure mounting hardware according to your desired
light beam angle.
For technical support call us at 855-760-5337.
* Rigid Industries always recommends installation from an
industry professional. Be sure to read warranty information on back.
Congratulations on your purchase of Rigid Lights!
Insert mounting brackets onto light as shown in Diagram
1.
A or B. Secure hardware to a snug position and mount
your light into desired location. The 4", 6" & 10" E-Series
and 6" & 10" SR-Series light bars include bolts that slide
into each side of light housing before compression
spacers and brackets are attached for mounting.
Disconnect the negative battery cable from the battery.
2.
Attach red terminal eyelet to battery positive or any
3.
12V DC source. Secure black terminal to suitable ground
or battery negative. Route harness to desired switch and
mounting locations, secure with zip ties. Beware of sharp
edges, abrasive surfaces and heat sources when wiring.
When installing Rigid lights on a 24V DC system be
4.
sure to use a 24V relay. When installing multiple lights
be sure to have adequate fusing.
5. Finally, test lights to ensure proper function and then
secure mounting hardware according to your desired
light beam angle.
For technical support call us at 855-760-5337.
* Rigid Industries always recommends installation from an
industry professional. Be sure to read warranty information on back.
Battery Eyelets
- Red to positive
- Black to negative
Switch Wiring
E-Series 4"-10"
SR-Series 6"-10"
Black wire to gold prong (switch ground)
Red wire to middle prong (black strip) (switch output)
Red wire to remaining prong (switch power)
E-Series 20"-50"
SR-Series 20"-50"
E-Series/E2 4"-10"
Black wire to gold prong (switch ground)
plug directly into light.
Blue wire to middle prong (switch output)
Red wire to remaining prong (switch power)
Battery Eyelets
- Red to positive
- Black to negative
Switch Wiring
E-Series 4"-10"
SR-Series 6"-10"
Black wire to gold prong (switch ground)
Red wire to middle prong (black strip) (switch output)
Red wire to remaining prong (switch power)
E-Series 20"-50"
SR-Series 20"-50"
E-Series/E2 4"-10"
Black wire to gold prong (switch ground)
plug directly into light.
Blue wire to middle prong (switch output)
Red wire to remaining prong (switch power)
covers & Accessories
Available!
Minimum Fusing
Requirements
SR-Series
(5 amps - 6")(10 amps - 10")
(15 amps - 20", 30", 40", 50")
E-Series
(5 amps - 4", 6")(10 amps - 10")
(15 amps - 20", 30", 40")(20 amps - 50")
Drill 3/4" Hole
to Install Switch
Visit RigidIndustries.com for more accessories!
covers & Accessories
Available!
Minimum Fusing
Requirements
SR-Series
(5 amps - 6")(10 amps - 10")
(15 amps - 20", 30", 40", 50")
E-Series
(5 amps - 4", 6")(10 amps - 10")
(15 amps - 20", 30", 40")(20 amps - 50")
Drill 3/4" Hole
to Install Switch
Visit RigidIndustries.com for more accessories!
*Clear covers are also available
*Clear covers are also available