Storing The Tractor; Maintenance - Cub Cadet Zero Turn ZTS2 Operator's Manual

Storing the Tractor

• Allow the machine to cool in an open area for at least five
minutes before storing.
• Do not park the tractor near any flammable materials (wood,
cloth or chemicals) or any open flames or other potential
source of ignition (furnace, water heater or any other type
of heater).
• Remove all combustible materials from the tractor before
storing. Empty cargo boxes, grass catchers or containers.
• Always shut off fuel flow when storing or transporting if
tractor is equipped with a fuel shutoff.
• Check the fuel system (lines, tank, cap and fittings) per the
Maintenance Schedule for cracks or leaks. Repair and clean
as necessary.

Maintenance

REMOVING THE FLOOR PANEL
Do not operate tractor with floor panel removed.
The floor panel can be removed for maintenance, service and
cleaning. To remove the floor panel:
1. Using the multi-tool or a 1/2" socket, remove the hex screw
(a) that secures the floor panel in place. See 1 in Figure 24.
1
(a)
2
Figure 24
2. Carefully lift the rear of the floor panel. See 2 in Figure 24.
3. Slide the floor panel rearward to free the front of the floor
panel. See 3 in Figure 24.
4. Lift it off the tractor. See 4 in Figure 24.
5. To place the floor panel back on the tractor, carefully put
the floor panel back in place and re-install the hex screw
removed in Step 1. Torque to 108-132 in-lbs (12-15 N-m).
ENGINE
Allow machine to cool in an open area for at least five
minutes before storing or refueling.
Refer to the Engine Operator's Manual for all engine maintenance
procedures and instructions.
PRODUCT CARE
WARNING
4
3
WARNING
NOTE: Maintenance, repair or replacement of the emission
control devices and systems which are being done at owner's
expense may be performed by any engine repair establishment
or individual. Warranty repairs must be performed by an
authorized dealer.
CHANGING THE ENGINE OIL
If the tractor has been recently run, the engine, muffler,
and surrounding metal surfaces will be very hot and can
cause burns to the skin. Let the engine cool for at least
five minutes. Exercise caution to avoid burns.
NOTE: The oil filter should be changed at every oil
change interval.
To complete an oil change, proceed as follows:
1. Locate the oil drain hose (a) on the side of the engine. See
Figure 25.
2. Place an appropriate oil collection container with at least a
2.5 quart (2.37 liter) capacity below the opening of the oil
drain hose, to collect the used oil. Remove the oil fill cap/
dipstick (b) from the oil fill tube. See Figure 25.
3. While holding the free end of the oil drain hose over the oil
collection container, unscrew the square head hose plug (c)
from the end of the oil drain hose. See Figure 25. Drain the
engine oil into the collection container.
(d)
(a)
(c)
4. After draining the oil, wipe any residual oil from the oil drain
hose. Thread the square head hose plug into the oil drain
hose fitting and tighten the square head hose plug to
16 ft-lbs (22 N-m).
5. Remove the oil filter (d) and drain into the collection
container. See Figure 25.
6. Replace the oil filter (d) and refill the engine with new oil as
instructed in the Engine Operator's Manual. See Figure 25.
NOTE: Place an absorbent towel beneath the oil filter to keep oil
off the clutch.
NOTE: Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
NOTE: Maintenance, repair or replacement of the emission
control devices and systems which are being done at owner's
expense may be performed by any engine repair establishment
or individual. Warranty repairs must be performed by an
authorized dealer.
23
WARNING
(b)
Figure 25