Advertisement
Page 6 of 8
KEEP SAFETY LABELS IN GOOD
CONDITION AND REPLACE IF MISSING
OR DAMAGED.
IMPORTANT: To prevent unnecessary strain on
piping system and valving, always shut off pump
before switching Filter Control Valve positions.
To prevent damage to the pump and filter and for proper
operation of the system, clean pump strainer and
skimmer baskets regularly.
FILTER CONTROL VALVE FUNCTIONS
FILTER—Set valve to FILTER for normal filtering. Also
use for regular vacuuming.
BACKWASH—For cleaning filter. When filter pressure
gauge rises 8-10 PSI (0.55-0.69 BAR) above start-up
(clean pressure):
Stop the pump, set valve to BACKWASH. Start pump
and backwash until water in sight glass is clear.
Approximately 2 minutes or less depending on dirt
accumulation. Proceed to RINSE.
This equipment was inspected before shipment from our plant. To original purchasers of this equipment, Hayward
Pool Products, 620 Division Street, Elizabeth, New Jersey, warrants its products free from defects in materials and
workmanship for a period of ONE (1) year from the date of purchase.
Parts which fail or become defective during the warranty period, except as a result of freezing, negligence, improper
installation, use, or care, shall be repaired or replaced, at our option, without charge, within 90 days of the receipt of
defective product, barring unforeseen delays.
To obtain warranty replacements or repair, defective components or parts should be returned, transportation paid, to
the place of purchase, or to the nearest authorized Hayward service center. For further Hayward dealer or service
center information, contact Hayward customer service department. No returns may be made directly to the factory
without the express written authorization of Hayward Pool Products, Inc.
To original purchasers of this equipment, Hayward Pool Products, Inc. warrants its vacuum release systems to be
free from defects in materials and workmanship for a period of ONE (1) year from the date of purchase.
Filters which become defective during the warranty period, except as a result of freezing, negligence, improper
installation, use or care, shall be repaired or replaced, at our option, without charge.
All other conditions and terms of the standard warranty apply.
Hayward shall not be responsible for cartage, removal and/or reinstallation labor or any other such costs incurred in
obtaining warranty replacements.
The Hayward Pool Products warranty does not apply to components manufactured by others. For such products, the
warranty established by the respective manufacturer will apply.
Some states do not allow a limitation on how long an implied warranty lasts, or the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
*Supersedes all previous publications.
WWW.HAYWARDPOOL.COM
MODEL S210T, S210T90
®
HAYWARD
LIMITED WARRANTY
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
RINSE—After backwashing, with pump off, set valve to
RINSE. Start pump and operate for about 1/2 to 1 minute.
This ensures that all dirty water from backwashing is
rinsed out of the filter to waste, preventing possible return
to the pool. Stop pump, set valve to FILTER, and start
pump for normal filtering.
WASTE—To bypass filter for draining or lowering water
level and for vacuuming heavy debris directly to waste.
RECIRCULATE—Water is recirculated through the pool
system, bypassing the filter.
CLOSED—Shuts off flow from pump to filter.
VACUUMING—Vacuuming can be performed directly into
the filter. When vacuuming heavy debris loads, set valve
to WASTE position to bypass the filter and vacuum
directly out to waste.
'NOTE: For new concrete or gunite pools, or where there is a large amount
of plaster dust or debris—start filter in FILTER position (not
BACKWASH) to prevent clogging of underdrain laterals.
Hayward Pool Products
620 Division Street
Elizabeth, NJ 07207
IS210T90 Rev D
Advertisement
