Related Manuals for Hyundai HYMS1500E
Summary of Contents for Hyundai HYMS1500E
- Page 1 MITRE SAW HYMS1500E Instruction Manual WARNING: Read the instructions carefully before use.
-
Page 2: Table Of Contents
Contents Introduction……..……………………………3 Specifications……………………....37 Recycling And Disposal..………………...38 Safety Information…..…………………..4-13 Understand Your Machine.…..…………...4 Declaration Of Conformity…..…………..39 Personal Safety...…….……………………4-5 Inspect Your Machine…………………..5 Work Area…….……………………………..6 Useful Information…..……………………..40 During Use…….………………………………7 Our YouTube Channel…..………………..40 Batteries…….…………………………………8 Warranty…………………………………….40 Electricity…….………………...…………...8-9 Manual Updates….……………………….40 Double Insulated Devices…..……..9 Returning Your Product….……………….40 Vibrations….…………………………..10 Leaving A Review….……………………...40 Noise…….……………………………..10 Ordering Spare Parts.……………………..40... -
Page 3: Introduction
THE MACHINE. Keep for future reference and pass it on if the machine is loaned or sold to another user. This manual has been produced by Hyundai Power Products and should be kept with the product. Please read and understand these instructions before you use your product. -
Page 4: Safety Information
Safety Information Understand Your Machine • WARNING! You must read these instructions carefully before operating the machine. Make sure that you are familiar with the controls and properly operate the machine. You must learn how to stop the machine quickly. If you do not follow the warnings and instructions, it may result in fire and/or serious injury. -
Page 5: Inspect Your Machine
Safety Information Personal Safety (Continued) • Do not touch parts that might be hot from operation. Allow parts to cool before attempting to maintain, adjust, or service. • Do not overreach. Keep proper footing and balance at all times. This enables better control of the machine in unexpected situations. -
Page 6: Work Area
Safety Information Work Area • You must only work in daylight or with good artificial light in good visibility conditions. Do not work at night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the area. -
Page 7: During Use
Safety Information During Use • Do not operate the machine in confined areas where there may be a risk of crushing the operator between the machine and another object. • Never attempt to make any adjustments, while the machine is running. •... -
Page 8: Batteries
Safety Information Batteries (Where Present) Batteries present a risk if they become damaged by the possible leaking of electrolyte. This electrolyte is an acid and can cause serious burn injuries. Care should be taken when working on or near them. NOTE: the electrolyte may be in a liquid or gel form. -
Page 9: Double Insulated Devices
Safety Information Electricity (Continued) • Power tools plug must match the outlet. Never modify the plug in any way. DO NOT use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. •... -
Page 10: Vibrations
Safety Information Vibrations (Where Applicable) • Prolonged use of hand held (operated) machines will cause the user to feel the effects of/from vibrations. These vibrations can lead to white finger (Raynaud’s phenomenon) or carpal tunnel syndrome. This condition reduces the ability of the hand to feel and regulate temperature, causing numbness and heat sensations and may cause nerve damage and circulatory tissue death. -
Page 11: Intended Use
Safety Information Intended Use The HYMS1500E is an electric Mitre Saw from HYUNDAI. The HYMS1500E is powered by a 2000W HYUNDAI motor. This machine is a specifically a pedestrian tool, manufactured according to the latest safety requirements. Every precaution is only effective when it’s followed exactly. -
Page 12: Personal Protective Equipment
Safety Information Personal Protective Equipment Appropriate Personal Protective Equipment (PPE), MUST be worn at all times when operating or repairing the machine. No protective equipment can ensure 100% protection. When selecting PPE, make sure it’s CE marked and it suits the user in terms of size, fit, etc. -
Page 13: Symbols On The Machine
Safety Information Symbols On The Machine We have provided safety messages in this manual and on the machine. This information alerts you to potential hazards that could hurt you or others. Please read these messages carefully. However, we may not have listed all of the possible hazards, you must also use your own judgement. -
Page 14: Unboxing
2. Lay the contents out and check them. If any part is damaged or missing, you must not use the machine. Contact HYUNDAI POWER PRODUCTS immediately. 3. You must keep the packaging material in case the machine needs to be returned or repaired. -
Page 15: Features
Features *Not To Scale Continued on next page www.hyundaipowerproducts.co.uk... - Page 16 Features *Not To Scale Continued on next page www.hyundaipowerproducts.co.uk...
- Page 17 Features *Not To Scale Descriptions on next page www.hyundaipowerproducts.co.uk...
- Page 18 Features Operating Handle Power Safety Switch Fixed Blade Guard Spindle lock Guard Mounting Plate Retractable Blade Guard Saw Blade Adjustable Fence Extendable Support 10. Mounting Hole 11. Saw Table 12. Turntable Locking Handle 13. Mitre Angle Adjustment Lever 14. Support Bolt 15.
-
Page 19: Assembly
Remove from Storage Configuration Ensure the machine is unplugged from a power source. After taking your HYMS1500E out of the box, take it out of Storage configuration. Press and hold the Mitre Angle adjustment Lever down, and rotate the machine to on the Mitre Scale. -
Page 20: Turntable Locking Handle
Assembly Turntable Locking Handle Insert the Turntable Locking Handle into it’s slot. After inserting the Turntable locking handle, rotate it clockwise to secure it into place. When the handle stops spinning, this means it’s fully locked into position. Continued on next page www.hyundaipowerproducts.co.uk... - Page 21 Assembly Turntable Locking Handle (Continued) www.hyundaipowerproducts.co.uk...
-
Page 22: Upper Handle
Assembly Upper Handle 1. Locate the 2 holes used to secure the upper handle 2. Line up the holes with the those in the upper handle. 3. Using the bolt and screw provided secure the handle into place. Tighten using the Multi-tool provided. - Page 23 Assembly Upper Handle (Continued) www.hyundaipowerproducts.co.uk...
-
Page 24: Dust Bag
Assembly Dust Bag . 1 . Squeeze together the tabs on the dust bag. 2. Place the Dust bag over the Dust Extraction Outlet 3. Gently pull on the bag to ensure it’s seated correctly. www.hyundaipowerproducts.co.uk... -
Page 25: Work Piece Clamp
Assembly Work Piece Clamp On both sides of the machines there is a Location hole for the workpiece clamp. Insert the workpiece clamp into the side of your choice. Then tighten the Workpiece Clamp retention screw using the Multi-tool provided. Continued on next page www.hyundaipowerproducts.co.uk... - Page 26 Assembly Work Piece Clamp (Continued) www.hyundaipowerproducts.co.uk...
-
Page 27: Operation
Operation Unlocking Saw Hinge To unlock the Saw Hinge you must slide the locking bolt into the out position. To allow this, you may need to press the saw down slightly. This is due to the Saw Head being spring loaded. www.hyundaipowerproducts.co.uk... -
Page 28: Securing Workpiece
Operation Securing Workpiece 1. Adjust the height of the Workpiece Clamp to sufficiently secure the workpiece to the Saw Turntable. 2.If the Workpiece is too long for the Saw Turntable, use the Extendable Support in order secure the workpiece. 3. Also use the Adjustable Fence to secure the workpiece from rotating. 4. - Page 29 Operation Securing Workpiece (Continued) Continued on next page www.hyundaipowerproducts.co.uk...
- Page 30 Operation Securing Workpiece (Continued) Ensure tight before operation. www.hyundaipowerproducts.co.uk...
-
Page 31: Starting / Stopping
Operation Starting and Stopping 1. To start the machine, you must press the Safety Switch. 2. While holding the Safety Switch, also press the On/Off Switch. The machine will start. To stop the machine simply release both switches. Continued on next page www.hyundaipowerproducts.co.uk... -
Page 32: Sliding Cuts
Operation Sliding Cuts To enable the sliding function, loosen the Sliding Rail Lock. Continued on next page www.hyundaipowerproducts.co.uk... - Page 33 Operation Sliding Cuts (Continued) The Blade won’t cut the full width of the work piece, needed the sliding feature The Blade is now able to cut the full width of the workpiece www.hyundaipowerproducts.co.uk...
-
Page 34: Altering Cutting Angle
Operation Altering Cutting Angle To alter the cutting angle of the saw, loosen the Bevel lock at the rear of the machine. This will allow the machine to pivot to your chose angle. When you have reached your preferred cutting angle, tighten the Bevel Lock to secure the chosen angle. - Page 35 Operation Altering Cutting Angle (Continued) www.hyundaipowerproducts.co.uk...
-
Page 36: Maintenance & Care
Maintenance & Care General Maintenance WARNING : Turn OFF the machine, allow all moving parts to come to a complete stop, and disconnect the power cord before maintaining the machine. You need to wear proper clothing and protective gloves whenever your hands are at risk. -
Page 37: Specifications
Technical Data Specification Model HYMS1500E No Load Speed 5000r/min Voltage 230V-240V ~ 50Hz Power 1500W Net Weight 15kg Blade Diameter 216mm (24 Teeth) Blade Bore 30mm www.hyundaipowerproducts.co.uk... -
Page 38: Recycling And Disposal
Recycling & Disposal Recycling & Disposal We do not offer a takeback scheme for the recovery of Waste Electrical Electronic Equipment (WEEE) & Batteries. Instead the responsibility to dispose of WEEE and/or Batteries is passed onto you by us. So when it becomes necessary to dispose of your machine you must take it to your local Civic Amenity Site. -
Page 39: Declaration Of Conformity
Genpower Ltd Isaac Way, Pembroke Dock, SA72 4RW Country of Origin: China Description: 1500W Mitre Saw SKU Code: HYMS1500E Date of Issue: 03/11/2021 Regulations and Directives of Compliance • 2006/42/EC The Machine Directive • 2014/30/EU EMC Directive • 2000/14/EC Noise Emissions •... -
Page 40: Useful Information
Go to YouTube and search ‘Hyundai Power Products’. Warranty Proof of purchase will be required before you make a warranty claim. Full warranty terms and conditions can be found on the HYUNDAI POWER PRODUCTS website: www.hyundaipowerproducts.co.uk Manual Updates Our manuals are constantly being reviewed and updated. Should you find an error, omission or something unclear, please contact us for assistance. -
Page 41: Product Record
Product Record Information As soon as you have purchased the machine, we recommend that you fill out the following. If you need to contact an authorised dealer or customer service for information on servicing, you may need to provide the following information. Date Of Purchase:……………………………………………………………………………….. -
Page 42: Contact Us
Our friendly aftersales team will be more than happy to help you. Phone Call our team on 01646 687 880 Email aftersales@hyundaipowerproducts.co.uk Online Live Chat Go to www.hyundaipowerproducts.co.uk Post Genpower Ltd, Isaac Way, Pembroke Dock, Pembrokeshire, SA72 4RW. Hyundai Support Website Go to hyundaisupport.co.uk www.hyundaipowerproducts.co.uk... - Page 43 Importer: GENPOWER LTD Isaac Way, London Road, Pembroke Dock, UK, SA72 4RW. T: +44 (0) 1646 687 880 E: info@hyundaipowerproducts.co.uk www.hyundaipowerproducts.co.uk Imported / Distributed by Genpower Ltd for the United Kingdom & Ireland Licensed by Hyundai Corporation, Korea...
Need help?
Do you have a question about the HYMS1500E and is the answer not in the manual?
Questions and answers