ClearSpan PB00556R3S Manual
  1. Manuals
  2. Brands
  3. ClearSpan Manuals
  4. Greenhouse Kit
  5. PB00556R3S
  6. Manual

ClearSpan PB00556R3S Manual

Portable freestanding building
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
©2008 ClearSpan™
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 06.11.08
ClearSpan
Portable Freestanding Building
Diagram may show a different but similar model.
CLEARSPAN
GARAGES & STORAGE SHEDS
™
™
STK#
DIMENSIONS
PB00556R3S
12' W x 10' H x 24' L
PB00556R4S
12' W x 10' H x 24' L
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PB00556R3S and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ClearSpan PB00556R3S

Summary of Contents for ClearSpan PB00556R3S

  • Page 1 CLEARSPAN GARAGES & STORAGE SHEDS ™ ClearSpan ™ Portable Freestanding Building Diagram may show a different but similar model. ©2008 ClearSpan™ All Rights Reserved. Reproduction STK# DIMENSIONS is prohibited without permission. PB00556R3S 12' W x 10' H x 24' L...

  • Page 2: Safety Precautions

    • Never erect the structure under power lines. • Identify whether underground cables and pipes are Thank you for purchasing this ClearSpan™ shelter. When present before preparing the site or anchoring the properly assembled and maintained, this product will structure.

  • Page 3: Assembly Procedure

    These words and phrases are common to most joints and to fasten brackets to rafters. ClearSpan™ shelters and identify the different parts of the shelter. (Some are used in this document. Others may not apply to this particular shelter.) These terms describe the shipped parts and can also be found on the materials list/spec sheets included with the shipment.

  • Page 4: Required Tools

    CLEARSPAN GARAGES & STORAGE SHEDS ™ SPECIAL NOTE: Wheel Jack Mounting Board REQUIRED TOOLS These instructions describe installing a mounting board The following list identifies the main tools needed to on the inside of the frame. The mounting board runs from assemble the shelter.
  • Page 5 CLEARSPAN GARAGES & STORAGE SHEDS ™ The following graphics and photos will help you identify the different parts and show you how they are used. (All parts are not shown.) FA4482B QH1400 QH1061 Tek Screw Band Clamp Ratchet ATTENTION: Actual...
  • Page 6 CLEARSPAN GARAGES & STORAGE SHEDS ™ Round Style Portable Freestanding Building OVERVIEW This section is an overview of the process for assembling your Round Style Portable Freestanding Building. For details, please see the Assembling the Round Style Portable Freestanding Building Components section.

  • Page 7: Rafter Assembly

    CLEARSPAN GARAGES & STORAGE SHEDS ™ ASSEMBLING THE ROUND STYLE PORTABLE FREESTANDING BUILDING COMPONENTS NOTE: Assistance is required to assemble the shelter. RAFTER ASSEMBLY Gather the Parts: 1˝ • Rafter Position #1 (Pipe #12R1301) Tek screw • Rafter Position #2 (Pipe #12R1302) •...

  • Page 8: Frame Assembly

    (plumb). Position the bolt side of end clamp to the inside of the frame. SKU # Rafter Spacing center-to-center PB00556R3S 36" PB00556R4S 48" 2. Insert the plain end of one 75” purlin pipe into each end 6.
  • Page 9 CLEARSPAN GARAGES & STORAGE SHEDS ™ FRAME ASSEMBLY (CONTINUED) MOUNTING BOARD INSTALLATION 10. Continue adding rafters and purlins until the frame is The mounting board is supplied by the customer. For this assembled. example, it is attached above the bottom purlin along both sides of the frame on the inside of the frame.

  • Page 10: Strut Assembly

    CLEARSPAN GARAGES & STORAGE SHEDS ™ MOUNTING BOARD INSTALLATION (continued) STRUT ASSEMBLY After the rafter assembly is complete and the mounting boards are attached, verify that the band clamps are in the 3. Secure the mounting boards to the interior rafters using proper locations.
  • Page 11 CLEARSPAN GARAGES & STORAGE SHEDS ™ INSTALL PIVOT WHEEL ASSEMBLY FINISH ROUGH EDGES When the wheel pivot wheel assembly is properly installed Gather the parts: and locked in the down position, the frame assembly will be • Duct tape (supplied by customer) off the ground.
  • Page 12 CLEARSPAN GARAGES & STORAGE SHEDS ™ PREPARE MAIN COVER 2. Assemble two cover conduits. Start each conduit assembly with one 73.5" pipe and add 75" swaged Gather the parts: pipes to arrive at the correct length. Secure each pipe joint with a Tek screw and wrap each joint using •...
  • Page 13 CLEARSPAN GARAGES & STORAGE SHEDS ™ ATTACH MAIN COVER 4. Once the main cover is pulled into position, center the cover on the frame and remove the ropes. Loosely Gather the parts: secure the ends of the cover to the ratchets attached to the front and back end rafters.
  • Page 14 CLEARSPAN GARAGES & STORAGE SHEDS ™ ATTACH MAIN COVER (CONTINUED) 12. Repeat the steps for the remaining ratchet or ratchets. 8. Repeat the steps for the remaining D-ring strap or 13. Using additional help (if needed) tighten the main cover straps.
  • Page 15 If the shelter is moved, inspect all parts and connections before reassembling. • For replacement or missing parts, call 1-800-245-9881 for assistance. NOTE: With the exception of Truss Arch buildings, ClearSpan™ shelters and greenhouses do not have any tested loading criteria. Revision date: 06.11.08...
  • Page 16 CLEARSPAN GARAGES & STORAGE SHEDS ™ QUICK START GUIDE 12' Wide Round Style Portable Freestanding Building Frame length and rafter spacing may differ from actual frame. Revision date: 06.11.08...
  • Page 17 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
  • Page 18 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
  • Page 19 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
  • Page 20 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
  • Page 21 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...

This manual is also suitable for:

Pb00556r4s

Table of Contents