Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Migomag 315PS
Summary of Contents for Migomag 315PS
-
Page 1: Front Cover
OPERATING MANUAL FOR MIGOMAG CLASSIC WELDING MACHINE 315PS (ITEM # AAC315PS) -
Page 2: Table Of Contents
INDEX FRONT COVER ............1 INDEX ................2 INTRODUCTION ............3 ASSEMBLY INSTRUCTIONS ........3 SETTING UP FOR OPERATION ......3-4 MACHINE CONTROLS ..........4 SHEILDING GAS ............5 WORK ENVIRONMENT ..........5 OPERATION ............... 5 SETTING UP GUN FOR WELDING ALUMINIUM ..6 WELDING HINTS ............ -
Page 3: Introduction
INTRODUCTION A few minutes spent reading about your new MIGOMAG MIG WELDING MACHINE will enable you to operate your machine efficiently and benefit from its many features. ASSSEMBLY INSTRUCTIONS 1. Fit the heavy-duty rubber tyred castor wheels and rear wheels to the chassis of the welder. -
Page 4: Machine Controls
Welding Voltage Adjustment 2. A correct shape weld bead not too high, or low, with The MIGOMAG 315CLASSIC welding voltage is correct fusion along the edge of the weld without regulated by a 2-position switch for course control and a undercut in the heat-affected zone. -
Page 5: Sheilding Gas
(1). extinguish. During the pause cycle the molten pool will The MIGOMAG 315 CLASSIC model has two voltage cool down. The arc will ignite again automatically at the selection switches, a course control (8) and fine voltage beginning of the following working cycle when the filler selection (6). -
Page 6: Setting Up Gun For Welding Aluminium
SETTING UP GUN FOR ALUMINIUM WELDING PARTS LIST 1. The Welding Gun PART NUMBER DESCRIPTION Remove the liner positioning nut from the adaptor block 1260005 Teflon Liner 1.0mm at the wire feed end of the gun cable, remove the gas 1260021 Teflon Liner 1.2mm nozzle, contact tip holder, gas diffuser/contact tip from... -
Page 7: Welding Faults
WELDING FAULTS FAULT POSSIBLE CAUSE & REMEDY Weld deposit 'stringy' and incomplete 1. Torch moved over work piece too quickly 2. Gas mixture incorrect Weld deposit too thick 1. Torch moved over work piece too slowly 2. Welding voltage too low unstable, excessive spatter and weld porosity... - Page 9 Open cylinder valve and check the Close cylinder valve Fit gas hose to regulator and open cylinder pressure (Must be greater than cylinder valve. Set flow to 15 lt/min. 10bar (150lb/in2)) Larger torch may need 20 lt/min.
-
Page 10: Sheilding Gas Table
SHEILDING GAS TABLE MIG WELDING Metal Remarks Mild Steel Argon + CO2 Argon controls spatter Argon + CO2 + Oxygen Oxygen improves arc stability Stable arc – sound welds Aluminium Argon Argo Helium Higher heat input suitable for heavy sections Stainless Steel Argon + CO2 + Oxygen Arc stability... -
Page 11: Machine Breakdown
MIGOMAG 315PS CLASSIC MACHINE BREAKDOWN & PARTS DESCRIPTION PART NO. DESCRIPTION PART NO. DESCRIPTION 86001079B Left Hand Side Panel 86001019 Main Contactor DIL-K7-10 86001079A Right Hand Side Panel 86001030 Fan PAPST 86001042B Rear Wheel Assy 86001029 Fan Guard 86001038 Rubber Wheel Dia. 160mm 86002054P Fuse 2.5AMP 30 x 6 (10pkt) -
Page 12: Warranty
The warranty does not compensate for damage due to improper use, neglect or normal wear. Travelling costs, freight or postage charges are not covered by the warranty. Warranty repairs must be carried out at the premises of Migomag Welding Supplies or its authorised Service Repatr Agent. Repairs by unauthorised persons will void this warranty. -
Page 13: Contact Details
Lawvale Pty Ltd trading as: MIGOMAG WELDING SUPPLIES A.B.N. 50 007 120 603 THE LARGEST INDEPENDENT WELDING EQUIPMENT SUPPLIER IN AUSTRALIA 668 Somerville Road Sunshine Victoria 3020 Phone: 03 9313 3100 Fax: 03 9312 4499 63 Douro Street North Geelong Victoria 3215...
Need help?
Do you have a question about the 315PS and is the answer not in the manual?
Questions and answers