Subscribe to Our Youtube Channel
Related Manuals for Paxar Mobile Work Station (MWS) Monarch 9878
Summary of Contents for Paxar Mobile Work Station (MWS) Monarch 9878
- Page 1 Monarch™ 9878™ Compact Mobile Work Station (MWS™) TC9878COI Rev. AB 12/07 ©2007 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp. All rights reserved.
- Page 2 Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Paxar reserves the right to make changes in the product, the programs, and their availability at any time and without notice. Although Paxar has made every effort to provide complete and accurate information in this manual, Paxar shall not be liable for any omissions or inaccuracies.
-
Page 3: Table Of Contents
Connecting a Printer ........ - Page 4 PRINTING............5-1 About Sleep Mode .
-
Page 5: Getting Started
Describes how to connect power cords and use additional devices on the MWS. Describes how to charge the batteries. Describes battery power and battery safety issues. Explains how to print supplies from a printer on the MWS. Technical specifications about the MWS. Getting Started 1-1... -
Page 6: Safety Precautions
O r d e r i n g P r o g r a m m e r ’ s M a n u a l s The Packet Reference Manual, which describes how to create format and batch packets for printing labels, how to configure a Monarch® printer online, and how to perform other advanced techniques is available from our Web site. -
Page 7: About The Mws Unit
A B O U T T H E M W S The Compact Mobile Work Station is shipped assembled. Use this chapter to verify the cable connections. Front Right Side Left Side Back About the MWS 2-1... -
Page 8: Connecting The Power Cord
C o n n e c t i n g t h e P o w e r C o r d Make sure to set the proper voltage on the charger voltage selector switch on the right side of the charger (115V in U.S. or 230V International). Incorrect voltage selection can result in charger failure. -
Page 9: Connecting An Ac Device
Contact your Monarch Representative for instructions on attaching a Monarch® printer to the MWS. U s i n g o t h e r M o n a r c h ® P r i n t e r s Contact your Monarch Representative for instructions on connecting Monarch®... - Page 10 2-4 About the MWS Unit...
-
Page 11: Charging The Batteries
C H A R G I N G T H E B A T T E R I E S The Compact MWS' battery charger is a fully automatic, maintenance-free charger. The charger power switch does not control the MWS power. The MWS power switch located on the power panel controls power to the cart and connected devices. -
Page 12: Important Charging Information
I m p o r t a n t C h a r g i n g I n f o r m a t i o n DANGER! RISK OF ELECTRICAL AND FIRE HAZARD. CERTAIN ACTIONS MAY RESULT IN DEATH, SERIOUS Do not disassemble the battery charger. -
Page 13: About The Battery Status Leds
A b o u t t h e B a t t e r y S t a t u s L E D s The charger is mounted on the Power Panel. The MWS Battery Status LEDs are located on the top-left side of the Power Panel. To use the Battery Status LEDs, the MWS must be on. -
Page 14: Battery Life
The 24VDC charger has a Power LED and five Percentage LEDs. When the charger is turned off (power LED off), the percentage LED shows battery status. The percentage LED flashes while charging to display battery status. When the batteries are fully charged, the 100 percent LED stays on. Power B a t t e r y L i f e If you leave the battery charger plugged in and... -
Page 15: Frequency Of Charging/Run-Time Guidelines
In the information below, “typical conditions” are defined as follows: one Monarch® printer printing standard compliance 4x6 labels (5-10 minutes of actual printing per hour), no auxiliary devices attached to the MWS, and standard environmental conditions (no excessive heat or humidity). - Page 16 3-6 Charging the Batteries...
-
Page 17: Power Options
OFF the MWS' The MWS' power switch controls the power to all devices on the MWS. If using more than one printer on the MWS, manually turn OFF each printer’s power switch. -
Page 18: About The Inverter
The AC power inverter provides 115V power to peripherals, such as a PC, scanner, charger, or printer. This equipment contains components which can produce arcs or sparks. To prevent fire or explosion, do not install near Flammable materials or in locations that require ignition-protected equipment (including gasoline-powered machinery, fuel tanks, joints, or fittings). -
Page 19: Printing
However, printing while charging is not recommended on a frequent basis. If the printer will be unused for extended periods of time, we recommend leaving the printhead unlatched. If the printer’s green power light blinks, you need to recharge the battery. -
Page 20: About Sleep Mode
Escape/Clear, the printer “wakes up” and you enter the offline menu mode. You can also send any data to the printer to wake it up. You do not lose any data sent to the printer during sleep mode. -
Page 21: Specifications
S P E C I F I C A T I O N S M o b i l e W o r k S t a t i o n ( M W S ) Height: Approximately 37 inches (940 mm) depending on selected options Top Width: 20.5 inches (521 mm) -
Page 22: Batteries
B a t t e r i e s (1) 12-volt, 55 amp-hour, deep cycle battery (2) 12-volt, 55 amp-hour, deep cycle batteries Sealed lead-acid, non-venting (safety venting only), no transportation restrictions Shelf Life/Charge Retention: 1 month 3 months 6 months Cycle Use: 100% depth of discharge 50% depth of discharge... -
Page 23: 24Vdc Models
2 4 V D C M o d e l s Input 90-132 VAC @ 5.0 A 180-264 VAC @ 2.5 A 50/60 Hz IEC 320-C14 Connection Output 24 VDC, 8 Amps DC charging current Reverse polarity and short circuit-proof 7 hour full charge, typical re-charge 3-6 hours 20-100 hour typical battery duration Smart charging...
Need help?
Do you have a question about the Mobile Work Station (MWS) Monarch 9878 and is the answer not in the manual?
Questions and answers