Related Manuals for Paxar Monarch 9805
Summary of Contents for Paxar Monarch 9805
- Page 1 Monarch 9805 Printer ONLINE TABLETOP PRINTER THERMAL DIRECT OR TRANSFER ON-DEMAND OR CONTINUOUS PEELS LABELS PRODUCES 4" X 6" IMAGES TC9805OI Rev. AA 7/99 ©1998 Monarch Marking Systems, Inc. All rights reserved.
- Page 2 édicte par le ministère des Communications du Canada. Trademarks MONARCH is a registered trademark of Monarch Marking Systems, Inc. 9805 is a trademark of Monarch Marking Systems, Inc. Paxar is a trademark of Paxar Corporation. Monarch Marking Systems P .O. Box 608 Dayton, Ohio 45401 WARNING CANADIAN D.O.C.
- Page 3 E s t a b l i s h i n g C o m m u n i c a t i o n s Before the printer can accept print jobs from the host, you must: Connect the communication cable to the printer and to the host.
- Page 4 Press Clear once to cancel the current print job. Press Clear twice to cancel all queued print jobs. To cancel a single or all queued print jobs, the printer must be in paused mode before Clear is pressed. To cancel all formats, batches, graphics, or check digits, turn off the printer.
- Page 5 If you are using thermal direct supplies, do not load a ribbon. Make sure the printer is configured for the correct supply type. If you experience supply feeding problems with 2.0-inch wide or less supplies, adjust the wide/narrow knobs to the wide setting.
- Page 6 See "Adjusting the Wide/Narrow Knobs" for more information. If the printer will be unused for extended periods of time, we recommend leaving the printhead unlatched. F o r P e e l M o d e : The minimum feed length is 1.5 inches for peel mode.
- Page 7 Make sure the backing paper tears at the edge. 5. Close the printer’s cover. 6. Press Feed to position the supply under the printhead. A d j u s t i n g t h e W i d e / N a r r o w K n o b s...
- Page 8 If the ribbon reels continue to turn when you change a ribbon, press Pause to stop the reels from turning. You can also change the ribbon when the printer is turned off. 1. Open the cover. 2. Unlock the printhead by turning the retaining latch.
- Page 9 P r i n t i n g 1. Turn on the printer. 2. Download a format and a batch. The printer prints a strip of labels. 3. Remove the printed labels. If you turn off the printer, you must wait 10-15 seconds (until the power light is completely dim) before turning it back on;...
- Page 10 A d j u s t i n g P r i n t C o n t r a s t You may need to adjust the print contrast if your printing is too dark or too light. Having the correct contrast is important because it affects how well your bar codes scan and how long your printhead lasts.
- Page 11 C l e a r i n g L a b e l J a m s If a jam occurs, the Supplies light on the printer’s front panel blinks. 1. Turn off the printer. Open the cover and printhead assembly.
- Page 12 7. Clean the build-up in the supply path. Let the printer dry before you reload supplies, close the exit cover, turn on the printer, press Feed to position the supply under the printhead, and resend your format/batch/graphic/check digit packets. R e p l a c i n g t h e P r i n t h e a d You may have to replace the printhead if it is damaged or worn-out.
- Page 13 If using on-demand mode, a test label prints only after all labels in the batch are printed and If you turn off the printer, you must wait 10-15 seconds (until the power light is completely dim) before turning it back on; otherwise, an error occurs.
- Page 14 Blank labels print or 750 series errors. Action Turn off the printer, wait fifteen seconds and then turn on the printer. Call Technical Support if the error message reappears. Check supply. Check ribbon. Send a corrected format and batch packet.
- Page 15 Printer sensed a mark in the wrong place. The 9805 printer does not support black mark supply. Printer sensed a mark that is too long. The 9805 printer does not support black mark supply. Check for a ribbon jam or remove any slack by turning the take-up reel clockwise.
- Page 16 Printhead has more than 10 bad dots or is not connected. Connect the printhead. The printer has an error pending. Turn off the printer. Wait 15 seconds (until the power light is completely dim) and turn it back on. Resend the packets.
- Page 17 For Thermal Direct 40 to 104 F (4 to 40 C) Print Speed: 2.5 ips (64 mm) for all serial bar codes and 4.0 ips (102 mm). 6.0 ips (152 mm) is available only for thermal transfer printing. S u p p l y S p e c i f i c a t i o n s For high temperature or high humidity environments, contact Monarch for supply recommendations.