A6001 Specifications; Connection Diagrams - Xtant A3001 Owner's Manual

Xtant A6001 Specifications
Frequency Response:
Number of Channels:
Watts per Channel @ 4Ω:
Watts per Channel @ 2Ω:
Recommended Load:
Distortion (THD):
Measured: 20 Hz to 120 Hz at rated power, all channels driven 4Ω
Signal to Noise Ratio:
Measured: A-weighted in 20 kHz noise bandwidth @ 1 volt sensitivity
Damping Factor:
Input Sensitivity:
Input to Line Output Gain:
On-Board Crossover:
Balanced Line:
Power Supply:
Operational Voltage:
Fusing Requirement:
Size (L xW x H):
Subsonic Filter:
Bass Boost:
Warranty:
6
All manuals and user guides at all-guides.com
English
20 Hz to 120 Hz +/– 1 dB
1
1 x 300
1 x 600
≥2Ω
≤ 2%
≥ 100 dB
≥ 100 @ 100 Hz with 4Ω load
100 mV to 8.5 V RMS Unbalanced
200 mV to 17 V RMS Balanced
0 dB
24 dB/Octave Low Pass
On Board
Fully Regulated, PWM
10 to 16 Volts
80 Amp
15-13/16" x 9-1/4" x 1-7/8"
402mm x 235mm x 47mm
24dB/Octave 20-80 Hz
0-12dB @ 45 Hz
Limited 4 Year Parts and Labor
(see page 8 for details)

Connection Diagrams

English
1. Input – Xtant A series amplifiers feature RCA type input connections.
1
Source units with an output signal level of 100mV – 17V may be used.
2
See "Balanced Input" for proper voltage level setting.
2. Output – These RCA type output connections send full range sig-
nals to additional amplifiers eliminating the need for "Y" connectors.
3. Balanced Input – The balanced input switch serves two purposes.
3
First, it helps eliminate noises being induced into the signal path by
isolating the signal ground. Second, it is used to set the proper
input voltage range:
Off Position: 100mV – 8V
On Position: 200mV – 17V
4. Gain – This feature is used to fine-tune the input sensitivity of the
4
amplifier to the source unit's output level.
5. Xover Frequency Control – This control allows the user to choose
the exact low-pass frequency range the amplifier will play for the
best possible performance. The upper end of the crossover frequen-
cies can be selected from 40Hz – 120Hz at 24dB per octave.
5
6. Bass Boost – This feature will add up to 12dB of low frequency
impact to the audio system. The Bass Boost is centered at 45Hz.
7. Subsonic – This feature limits the lower end of the low-pass fre-
quencies sent to the subwoofers. The subsonic feature includes a
selectable on/off switch, and a control knob used to adjust the
lower end of the low-pass range. The subsonic setting can be
6
selected from 20Hz-80Hz at 24dB per octave.
8. RLC – This port allows the use of the optional Xtant "remote level
control" (RLC). The RLC is a bass control module that can be
installed in any location within the vehicle for remote adjustments.
9. Speaker Connection – Two sets of speaker terminals are provid-
7
ed for dual woofer applications. When connecting a single woofer,
use only one set of speaker terminals. Warning, the Xtant A3001
and A6001 are not bridgeable.
10. Power Terminals – This is the main power connection for the
amplifier. The power and ground wire size should be the same gauge.
8
GND – The ground wire from this connection must be attached to
bare metal on the vehicle.
REM – To turn the amplifier on/off, this terminal must be connected
to the source unit's "remote or electric antenna" wire.
+12V – The power wire from this connection must be attached to
an inline fuse, then to the positive side of the vehicle battery.
9
WARNING: An outboard fuse must be installed in-line with the power
wire within 18 inches of the battery.
10
7