Related Manuals for DSE SD-5 Series
Summary of Contents for DSE SD-5 Series
- Page 1 8V ERWP EX IH J V SQ - X EP M ER X S )RKP M WL [ [ [ SRP M RIHSGX V ERWP EX SV GSQ USER MANUAL SPEED DOME CAMERAS SD-xxx-5 Page:1 SD-xxx-5 SERIES Cameras motorized AHD / analog WWW.DSE.EU...
- Page 2 Control of PTZ cameras cameras. They allow an operator to rotate the camera The speed-dome cameras are controlled with special in all directions and to zoom at will on the most control consoles or through DSE digital video recorders. interesting scenes. They...
-
Page 3: Installing The Camera
2 cables are wound together and All the elements of the RS485 BUS, both cameras and not parallel. Theoretically, the RS485 serial line can control units, must use the same protocol (PELCO D extend up to 1200 meters in length and the devices are WWW.DSE.EU... - Page 4 ID, but if there are more than one, you have to assign the value with the up and down arrows until it is equal them different addresses. to the DEVICE ID Proceed as follows: 1 - Call up PRESET 95 to open the OSD menu WWW.DSE.EU...
- Page 5 Once the address or the protocol speed has been changed, the camera will no longer respond to commands and it will be necessary to change the settings of the control unit in a manner consistent with the new settings. WWW.DSE.EU...
-
Page 6: Wall Mounting
The camera cable in this case must pass through the bracket. In the following photographs the example of installation of the wall bracket Connect the camera and secure it to the bracket with the supplied screws. WWW.DSE.EU... - Page 7 USER MANUAL SPEED DOME CAMERAS SD-xxx-5 Page:7 Other types of brackets are optionally available. WWW.DSE.EU...
-
Page 8: Basic Operations
PREVIEW or GO TO depending on the consoles. The camera moves automatically until it reaches the stored position. Each control unit uses different wordings sequences. Consult the documentation attached to the control unit to know the exact sequence to be dialed. Automatic movements Manual ZOOM control WWW.DSE.EU... - Page 9 The cameras can perform automatic movements such as panoramic scans or preposition sequences. These movements are set in the programming menu which is described below. These movements are started with the commands of the control unit or using the system presets. WWW.DSE.EU...
-
Page 10: System Preset
CALL Set AHD video Call the preset twice to set the video signal in AHD, used by 2 times DSE DVR CALL Set up TVI video Call the preset twice to set the TVI video signal, used by 2 times... -
Page 11: How To Operate
System PRESET 95. Typically you must first select the address of the camera you want to program, then type 95 and then press CALL or PREVIEW or GO TO (consult the console manual on how to recall a preset) WWW.DSE.EU... - Page 12 AUTOFLIP - It must be enabled if during the ILLUMINATION ON - It is the activation threshold vertical movement (TILT) you want the camera, of the LEDs on a scale from 0 to 15 having reached the vertical position, to rotate 180 WWW.DSE.EU...
- Page 13 IRIS - Sets the camera iris to automatic or CAM DATA - Restore factory settings of the manual. camera module BLC - Enables backlight compensation for shooting PRESET - Clear all presets a dark subject on a light background. WWW.DSE.EU...
- Page 14 W) or to switch automatically from color to B / W based MAIN MENU on the light (AUTO). It is possible to go to MAIN MENU and call preset 102 ADJUST -in this section the following parameters twice to access. You can control different camera are set: settings. WWW.DSE.EU...
- Page 15 FRAMERATE: you can choose between RT (Real Time) (Non Real Time) maximum resolution VIDEO OUT: It is possible to choose between European PAL and NTSC US format APPLY SET: Closes the menu and saves the settings RETURN: Return to the main menu WWW.DSE.EU...
Need help?
Do you have a question about the SD-5 Series and is the answer not in the manual?
Questions and answers