Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Lanner Manuals
  4. Computer Hardware
  5. HMB-6110
  6. User manual

Lanner HMB-6110 User Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Telecom Datacenter Appliances
HMB-6110
User Manual
Version: 0.3
Date of Release:2022-03-10
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the HMB-6110 and is the answer not in the manual?

Questions and answers

Related Manuals for Lanner HMB-6110

Summary of Contents for Lanner HMB-6110

  • Page 1 Telecom Datacenter Appliances HMB-6110 User Manual Version: 0.3 Date of Release:2022-03-10...
  • Page 2 - assumed to be qualified in the servicing of computer equipment, such as professional system integrators, or service personnel and technicians. The latest version of this document can be found on Lanner’s official website, available either through the product page or through the Lanner Download Center page with a login account and password.
  • Page 3 Support, where you can fill in a support ticket to our technical support department. This document is copyrighted © 2022 by Lanner Electronics Inc. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.
  • Page 4 HMB-6110 User Manual Taiwan Corporate Headquarters China Lanner Electronics Inc. Beijing L&S Lancom Platform Tech. Co., Ltd. 7F, No.173, Sec.2, Datong Rd. Guodong LOFT 9 Layer No. 9 Huinan Road, Xizhi District, New Taipei City 22184, Huilongguan Town, Changping District, Beijing...
  • Page 5 HMB-6110 User Manual Intel® and Intel® Celeron® are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries. Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp. All other product names or trademarks are properties of their respective owners.
  • Page 6 HMB-6110 User Manual Follow these guidelines to ensure general safety: Keep the chassis area clear and dust-free during and after installation. Do not wear loose clothing or jewelry that could get caught in the chassis. Fasten your tie or scarf and roll up your sleeves.
  • Page 7 The installation of this product must be performed by trained specialists; otherwise, a non-specialist might create the risk of the system’s falling to the ground or other damages. Lanner Electronics Inc. shall not be held liable for any losses resulting from insufficient strength for supporting the system or use of inappropriate installation components.
  • Page 8 HMB-6110 User Manual Before turning on the device, ground the grounding cable of the equipment. Proper grounding (grounding) is very important to protect the equipment against the harmful effects of external noise and to reduce the risk of electrocution in the event of a lightning strike. To uninstall the equipment, disconnect the ground wire after turning off the power. A ground wire is required and the part connecting the conductor must be greater than 4 mm2 or 12 AWG.
  • Page 9 HMB-6110 User Manual Main Features ........................10 Package Content ....................... 10 Ordering Information ......................10 Optional Accessories ......................10 System Specification ......................11 I/O Overview ........................12 Motherboard Information ....................13 Accessing the Compute Blade(s) ..................19 Installing the CPU(s) ......................20 Installing System Memory ....................
  • Page 10 Intel 2nd Generation Intel® Xeon® Scalable Processors (codenamed Skylake-SP/Cascade Lake) and C621/C627 PCH. HMB-6110 compute blade is built to be hot swappable, and thus the smart fans are hot swappable as well. This compute blade is built to optimize functionality, scalability and performance for our HTCA-6000 modular network appliance series.
  • Page 11 HMB-6110 User Manual Dual Intel® 2nd Generation Xeon® Scalable Processors (codenamed Skylake-SP/Cascade Lake-SP) with C621/C627 System 16x 288-pin DDR4 R-DIMMs, max. up to 512GB memory Memory capacity BIOS AMI SPI Flash BIOS ⚫ LAN: - Intel Ethernet 800 Series - 100G (KR4) x1 to top 1...
  • Page 12 HMB-6110 User Manual Description High Speed Connectors 2x Molex 288 PIN, 2x Molex 120 PIN, 2x Molex Power Connector OPMA Slot For 1x IAC-AST2500 IPMI 2.0 Module Cooling Fans 5x Smart Fan Rear I/O 1x USB 2.0, 1x RJ45 management port, 1x VGA Port...
  • Page 13 HMB-6110 User Manual The block diagram indicates how data flows among components on the motherboard. Please refer to the following figure for your motherboard’s layout design.
  • Page 14 HMB-6110 User Manual The motherboard layout shows the connectors and jumpers on the board. Refer to the following picture as a reference of the pin assignments and the internal connectors.
  • Page 15 HMB-6110 User Manual CONN3: For Power LED indication Description Anode Cathode CONN1: For Thumb Screw detection Description Detect JPWR1: For Power Button detection Description Power on JFAN1～JFAN5：For Fan Module Connection Description +12V RPM sense RPM sense PWM control JVGA1: For VGA Monitor Connection...
  • Page 16 PERP0 / SATA_RN PETN0 / SATA_TN PETP0 / SATA_TP REFCLKN DAS# REFCLKP PERST# CLKREQ# DETECT PEWAKE# CON1: For Lanner IPMI Card（IAC-AST2500） J36: For Lanner LAN Extension Card（HRC-61001） JPLD1: For Lanner CPLD Debug Purpose JRST1: For Reset Debug Purpose CON2: For Function Reserved...
  • Page 17 HMB-6110 User Manual JCMOS1：For Clear CMOS Description 1－2 Normal 2－3 Clear CMOS JHDA_SDO：For Flash Descriptor Security Override Description 1－2 Normal 2－3 Override JSPITPM：For Lanner TPM Module（IAC-TPM04）or SPI Fixture Debug Purpose J80P1：For Lanner LPC Fixture Debug Purpose...
  • Page 18 HMB-6110 User Manual To reduce the risk of personal injury, electric shock, or damage to the system, please remove all power connections to shut down the device completely. Also, please wear ESD protection gloves when conducting the steps in this chapter.
  • Page 19 HMB-6110 User Manual You have to access the compute blade(s) in order to install or replace CPUs, heatsinks, and DDR memory DIMMs. Please follow the steps below to access the compute blades. 1. Select a compute blade you wish to access the internal components.
  • Page 20 HMB-6110 User Manual Please note that the system delivered to you is already installed with the processor and that this processor comes with a rather sophisticated design; therefore, the assembly of which must be handled with exclusive tools and extreme care by professionals. It is strongly recommended that you not make any adjustments to, remove or even re-install the processor on your own.
  • Page 21 HMB-6110 User Manual This is packed along with the processor. Before performing any assembly involving this part, please locate PIN1 on one of the corners, an Processor Carrier important indicator used to align this carrier with the processor and the bolster plate correctly.
  • Page 22 HMB-6110 User Manual 3. For the other end of the carrier, align the alignment feature of the processor with the carrier latch, and then gently bend over the carrier end to have the latch secured on the processor. Latch 4. Align...
  • Page 23 HMB-6110 User Manual 1. Remove the dust cover from the socket contacts of the motherboard. Note: Inspect the surface of the socket under sufficient light to ensure there is no contamination or damage prior to the PHM installation. 2. Flip the PHM over to align...
  • Page 24 HMB-6110 User Manual 4. Make sure the PHM is sitting horizontally on the bolster plate. 5. Use a torque driver to tighten the four nuts to 12 in-lbf into the bolster plate following the sequence indicated on the heat sink (#1→ #2→ #3 → #4).
  • Page 25 HMB-6110 User Manual The motherboard supports 16 memory slots for DDR4 registered DIMM. Total Slots 16 (8 slots per processor) Number of Channels 6 Channels (4 for 1 Dimm per Channel, and 2 for 2 Dimm per Channel) Supported DIMM Capacity...
  • Page 26 HMB-6110 User Manual Please do follow the memory module installation instructions to install the DIMMs, and make sure  Each CPU requires at least 1 memory module to boot and run from.  If you do not plan to fill up all the sockets with 16 memory modules, always install memory modules starting with the blue sockets to avoid memory detection issues.
  • Page 27 HMB-6110 User Manual The motherboard provides one OPMA socket which is used to install an IPMI card. Please follow the steps for installation. 1. Locate the OPMA socket on the motherboard. 2. Align the notch of the IPMI card with the socket key in the slot. Insert at 30 degrees into the socket until it is fully seated in the connector until it is fully seated in the connector.
  • Page 28 HMB-6110 User Manual The motherboard provides one M.2 socket for SATA storage card. Please follow the steps for installation. Locate the M.2 socket on the motherboard. Align the notch of the M.2 storage card with the socket key in the slot. Insert the storage card at 30 degrees into the socket until it is fully seated.
  • Page 29 HMB-6110 User Manual Cooling fans are wearable components and may have to be replaced eventually. Please follow the steps below to replace cooling fans. 1. Locate the cooling fans at the rear of CPU blades. The fans are covered by a bezel.
  • Page 30 HMB-6110 User Manual This document specifies the BMC firmware features of Lanner. The BMC firmware implements IPMI 2.0 based on ASPEED service processor. It performs all the BMC management tasks defined by IPMI 2.0. In addition, Lanner’s BMC firmware runs an embedded web-server for full configuration using Web UI, which has a low learning curve.

  • Page 31: System Health Monitoring

    HMB-6110 User Manual System health monitoring The BMC implements system sensor monitoring feature. It could monitor voltage, temperature, and current of critical components. System Power Management The BMC implements chassis power and resets functions for system administrators to control and manage the system power behavior.

  • Page 32: Serial Over Lan (Sol)

    HMB-6110 User Manual Serial over LAN (SOL) IPMI 2.0 SOL is implemented to redirect the system serial controller traffic over an IPMI session. System administrators are able to establish a SOL connection with a standard IPMI client, like IPMITOOL, to remotely interact with serial text-based interfaces such as OS command-line and serial redirected BIOS interfaces.
  • Page 33 HMB-6110 User Manual IPMI Commands Support List COMMANDS NETFN IPM Device “Global” Commands Get Device ID APP (06h) Cold Reset APP (06h) Warm Reset APP (06h) Get Device GUID APP (06h) BMC Watchdog Timer Commands Reset Watchdog Timer APP (06h)
  • Page 34 HMB-6110 User Manual Clear SEL Storage (0Ah) Get SEL Time Storage (0Ah) Set SEL Time Storage (0Ah) Get SEL Time UTC Offset Storage (0Ah) Set SEL Time UTC Offset Storage (0Ah) LAN Device Commands Set LAN Configuration Parameters Transport (0Ch)
  • Page 35 HMB-6110 User Manual In the address bar of your Internet browser, input the IP address of the remote server to access the BMC interface of that server. Initial access of BMC prompts you to enter username and password. A screenshot of the login screen is given...
  • Page 36 HMB-6110 User Manual Username: admin Password: admin The default username and password are in lower-case characters. When you log in using the default username and password, you will get full administrative rights, and it will ask you to change the default password once you log in.
  • Page 37 HMB-6110 User Manual The BMC Web UI consists of various menu items: Menu Bar The menu bar displays the following: Dashboard Sensor Event Log Settings Remote Control Image Redirection Power Control Maintenance Sign out A screenshot of the menu bar is shown below:...
  • Page 38 HMB-6110 User Manual The user information and quick buttons are located at the top right of the Web UI. User Information Logged-in user information: Click the icon to view the logged-in user information. A screenshot of the logged-in user information is shown below: Logged-in User Information The logged-in user information shows the logged-in user’s username, privilege, with the quick buttons...
  • Page 39 HMB-6110 User Manual If your system is shipped without an operating system, install the supported operating system using the following resources. 1. Download the ISO image and make a bootable DVD from it. 2. Connect a DVD player or other type of readers (floppy disk, or a drive) to a computer.
  • Page 40 HMB-6110 User Manual Download the ISO image and save in a USB flash drive. Connect USB flash drive to the compute blade USB port. Take the VGA cable, included in the accessory box, and connect to the VGA port on the compute blade.
  • Page 41 HMB-6110 User Manual Connect to SOL via ipmitool command.  SOL usage: ipmitool -I lanplus -U [Username] -P [password] -H [compute blade BMC IP] sol [activate/deactivate]  Sample command to access compute blade 1 SOL: ipmitool -I lanplus -U admin -P admin -H 192.168.0.101 sol activate ...
  • Page 42 HMB-6110 User Manual 1. All products are under warranty against defects in materials and workmanship for a period of one year from the date of purchase. 2. The buyer will bear the return freight charges for goods returned for repair within the warranty period;...
  • Page 43 HMB-6110 User Manual When requesting RMA service, please fill out the following form. Without this form enclosed, your RMA cannot be processed.