Download
Share
Print this page
  1. Manuals
  2. Brands
  3. SI Manuals
  4. Projector Accessories
  5. FlexGlass In-Wall Gen 2
  6. Owner's manual

SI FlexGlass In-Wall Gen 2 Owner's Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
FlexGlass In-Wall
Owner's Manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the FlexGlass In-Wall Gen 2 and is the answer not in the manual?

Questions and answers

Related Manuals for SI FlexGlass In-Wall Gen 2

Summary of Contents for SI FlexGlass In-Wall Gen 2

  • Page 1 FlexGlass In-Wall Owner’s Manual...
  • Page 2 FlexGlass In-Wall Gen 2 FlexGlass Screen Material (Ships in separate package) Frame and Trim 2X Horizontal Frame 2X Vertical Frame 3X Flat Horizontal Trim 4X Flat Vertical Trim 1X 45º Horizontal Trim www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C...
  • Page 3 FlexGlass In-Wall Gen 2 Hardware Box contents 8 x Corner Brackets 8-32 Hex Nuts Shims Wood Screws 9/64 Ball Point Hex Driver 11/32 Nut Driver 1/8 Hex Key Gloves Driver Bit For Wood Screws www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C...
  • Page 4 FlexGlass In-Wall Gen 2 Pre-Assemble The Frame 1) Insert 8 Corner brackets into the slots in the shorter vertical frame pieces. 2) Make sure that the viewing sides stickers and posts in the tensioners are pointing the same direction a, then slide the corner brackets into the horizontal frame pieces, make sure all corners align well, and lock all set screws to secure corner brackets.
  • Page 5 FlexGlass In-Wall Gen 2 Install the Frame in the wall 3) Make sure the rough opening in the wall has been prepared such that it is 1/4’’ to 1/2’’ larger than the assembled frame. 4) Slide the frame into the rough opening and secure the bottom frame piece to the sill with the wood screws.
  • Page 6 FlexGlass In-Wall Gen 2 5) Use the shims to fill the gaps around the sides and top of the frame. Then Secure the side and top frame pieces to the rough opening with the wood screws drilled directly through the shims. Make sure the frame components are secured to the wall and straight before proceeding.
  • Page 7 FlexGlass In-Wall Gen 2 8) Spread out the tensioners approximately evenly spaced along the top and bottom frame. Then carefully lift the screen material up into the frame and onto the threaded posts on the tensioners. Secure the screen material to the tensioners with the hex nuts. Make sure the projection side is facing the projector location.
  • Page 8 FlexGlass In-Wall Gen 2 Tension the FlexGlass Material in the Frame 10) Tension the FlexGlass by turning the screws on the tensioners as shown below. 11) Continue applying tension to the screen all the way around until the FlexGlass is tight and flat.

  • Page 9: Attach The Trim

    FlexGlass In-Wall Gen 2 Attach the Trim 12) Snap in the vertical trim pieces first as shown. 13) Snap in the remaining trim pieces. Note that the single 45º trim piece goes on the projector side along the bottom if the projector is mounted on the floor or along the top if the projector is mounted on the ceiling.
  • Page 10 FlexGlass In-Wall Gen 2 LIMITED ONE YEAR WARRANTY ON SCREEN INNOVATIONS PRODUCTS Screen Innovations warrants its products to the original purchaser only, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser provided they are properly operated according to Screen Innovations’...
  • Page 11 FlexGlass In-Wall Gen 2 NOTES www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C...
  • Page 12 FlexGlass In-Wall Gen 2 NOTES www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C...