Table of Contents
Advertisement
Quick Links
I
NSTRUCTION
F
T
ORK
RUCK
M
ODEL
S
ERIAL
V
ESTIL
2999 N
ORTH
T
: (260) 665-7586 -
ELEPHONE
U
:
.
RL
WWW
VESTILMFG
M
OUNTED
M
FM-T-D
ODEL
N
. ________________________
O
N
. ________________________
O
M
ANUFACTURING
W
S
, P.O. B
AYNE
TREET
F
: (260) 665-1339
AX
.
COM
M
ANUAL
T
C
RASH
AN
UMP
C
507, A
OX
NGOLA
- T
F
(800) 348-0868
OR
OLL
REE
E
:
MAIL
SALES
D
UMPER
.
ORP
, IN 46703
@
.
VESTIL
COM
Advertisement
Table of Contents
Related Manuals for Vestil FM-T-DUMP
Summary of Contents for Vestil FM-T-DUMP
- Page 1 RASH UMPER FM-T-D ODEL . ________________________ ODEL . ________________________ ERIAL ESTIL ANUFACTURING 2999 N , P.O. B 507, A , IN 46703 ORTH AYNE TREET NGOLA : (260) 665-7586 - (800) 348-0868 ELEPHONE : (260) 665-1339 VESTILMFG MAIL SALES VESTIL...
-
Page 2: Safety Principles
Dump. Our product complies with ANSI cart and cart lifter standards to the extent that these rules apply. The reader should note that Vestil TH-64 trash carts used with the dumper are referred to in the industry as “residential carts” and in this manual they are called “carts”. -
Page 3: Table Of Contents
ABLE OF ONTENTS Safety Principles Product Introduction Safety Guidelines Use Instructions Maintenance & Inspections 10-11 ABLE OF IGURES FIG. 1: Rear View FIG. 2A: Side View FIG.2B: Cable Pulley FIG. 2C: Latch Assembly - 3 -... -
Page 4: Product Introduction
Furthermore, persons who use the cart dumper should have access to the manual at all times, and in particular should consult the directions before each use. Contact Vestil for answers to any question you have after reading the entire manual. -
Page 5: Safety Guidelines
Keep clear of the dumper while it is in use. DO NOT reach into the cart while it is connected to the dumper. • DO NOT use the FM-T-Dump to lift broken carts or carts that are overloaded. A broken or overloaded cart might break free of the dumper during use and could cause serious injuries. -
Page 6: Fig. 2A: Side View
FIG. 2A: Side View FIG. 2B: Cable Pulley FIG. 2C: Latch Assembly Latch Cross Quick Link Identification Part No. Description Quantity 37-514-023 Base Frame Weldment 37-514-022 Upright frame weldment An asterisk (*) next to a 37-612-001 Locking Pin Weldment number indicates that the 37-516-001 Can Adjustment Bracket Weldment corresponding part is a... -
Page 7: Use Instructions
Use Instructions: The cart dumper is intended to be used with a forklift truck, and therefore, only personnel who have successfully completed an approved operator training program like the one described in B56.1-2005, section 4.19.1-.5 should operate the cart dumper.. The operating instructions in this manual are intended to supplement the recommendations for safe forklift operation learned during a forklift training program or contained in ANSI/ITSDF standard B56.1, and ANSI standards Z245.1, .30, and .60. - Page 8 Step 5: Stow the Chute Release Handle. Feed the release cable through the fork carriage; attach the handle to the cage of the forklift in a location that will prevent the cable from getting in your way while driving the fork truck. Step 6: Engage a trash cart with the dumper.
- Page 9 Step 10: Empty the trash cart. Photographs 11-15 demonstrate use of the dumper to empty a trash cart into a moveable hopper. The fork lift operator approached the front of the hopper, and raised the forks to an appropriate height to avoid contact with the lip of the hopper (circled in photos 11 & 12). The operator drove the lift forward so that the dumper overhung the hopper by at least the width (W) of the trash cart as shown in photos 11 &...
-
Page 10: Maintenance & Inspections
Step 3: If deformity, corrosion, rusting, or excessive wear of structural members is present, DO NOT use the dumper. Contact Vestil for instructions. If the cart-engaging assembly does not rotate smoothly or makes noise when released, apply grease through the 3/16 inch grease fittings. If the mechanisms still function noisily even after applying lubricant, contact Vestil for directions. - Page 11 2. Date modification occurred; AND 3. Statement that all modifications comply with ANSI Z245.30-2008. Step 5: Contact Vestil for directions if a condition(s) are discovered during an inspection that is/are not addressed in this manual. Step 6: Make a dated record of the repairs, adjustments and/or replacements made.