1. Manuals
  2. Brands
  3. ELTEX Manuals
  4. Network Hardware
  5. LTP-8X
  6. Manual

ELTEX LTP-8X Manual

Hide thumbs Also See for LTP-8X:
Table of Contents

Advertisement

Quick Links

Download this manual
Optical line terminals
LTP-8X, LTP-4X
Application to the user manual
Quick configuration manual
Версия ПО 3.38.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LTP-8X and is the answer not in the manual?

Questions and answers

Related Manuals for ELTEX LTP-8X

Summary of Contents for ELTEX LTP-8X

  • Page 1 Optical line terminals LTP-8X, LTP-4X Application to the user manual Quick configuration manual Версия ПО 3.38.0...

  • Page 2: Table Of Contents

    LTP-X. Quick Configuration Manual 3.38.0 Содержание Annotation ..........................5 Safety rules and Installation procedure..................6 Safety requirements ........................6 Terminal installation ........................6 2.2.1 Support brackets mounting....................6 2.2.2 Terminal rack installation....................7 2.2.3 Power module installation....................8 2.2.4 Connecting to power supply....................9 Connecting to the Command Line Interface (CLI) ..............11 Connecting via telnet/ssh .......................11 Connecting via serial port......................11 Changing the user password ....................12...
  • Page 3 LTP-X. Quick Configuration Manual 3.38.0 APPENDIX C. RS-232 null-modem cable pin designation .............44 Appendix D. ONT NTU-1 configuration...................45 APPENDIX E. ONT SFP-ONU configuration................49 APPENDIX F. ONT/GPON interface status table ..............54   3...
  • Page 4   LTP-X. Quick Configuration Manual 3.38.0 Notes and warnings  Notes contain important information, tips, or recommendations on device operation and setup.  Warnings are used to inform the user about harmful situations for the device and the user alike, which could cause malfunction or data loss.

  • Page 5: Annotation

      LTP-X. Quick Configuration Manual 3.38.0 1 Annotation This manual specifies the following: Safety rules and Installation procedure • connection to the OLT LTP-X (hereinafter – the device) command line interface; • OLT network parameters configuration; • VLAN configuration to provide different services on switch; •...

  • Page 6: Safety Rules And Installation Procedure

      LTP-X. Quick Configuration Manual 3.38.0 2 Safety rules and Installation procedure 2.1 Safety requirements General requirements Any operations with the terminal should comply to the Safety Rules for Operation of Customers' Electrical Installations.  Operations with the terminal should be carried out only by personnel authorised in accordance with the safety requirements.

  • Page 7: Terminal Rack Installation

      LTP-X. Quick Configuration Manual 3.38.0 Figure 2  – Support brackets mounting 2.2.2 Terminal rack installation To install the terminal to the rack: • Step 1. Attach the terminal to the vertical guides of the rack. • Step 2. Align mounting holes in the support bracket with the corresponding holes in the rack guides. Use the holes of the same level on both sides of the guides to ensure the device horizontal installation.

  • Page 8: Power Module Installation

      LTP-X. Quick Configuration Manual 3.38.0 Figure 3 – Device rack installation The terminal is horizontally ventilated. The side panels have air vents. Do not block the air vents to avoid components overheating and subsequent terminal malfunction.  To avoid overheating and provide necessary ventilation of the terminal, sufficient space should be provided above and below the terminal, not less than 10 cm.

  • Page 9: Connecting To Power Supply

      LTP-X. Quick Configuration Manual 3.38.0 Figure 4 – Power module installation for LTP-X, LTP-X rev.B Figure 5 – Power module installation for LTP-X rev.C To install a power module: • Step 1. Install the power module into the socket shown in figure above; •...
  • Page 10   LTP-X. Quick Configuration Manual 3.38.0 • Step 3. If you intend to connect a PC or another device to the switch console port, the device must be properly grounded as well. • Step 4. Connect the power supply cable to the device. •...

  • Page 11: Connecting To The Command Line Interface (Cli)

      LTP-X. Quick Configuration Manual 3.38.0 3 Connecting to the Command Line Interface (CLI) 3.1 Connecting via telnet/ssh Connect the network data cable to one of the 'GE Port' or 'Combo GE' of LTP-X. The following factory settings are used for SSH/Telnet connection: •...

  • Page 12: Changing The User Password

      LTP-X. Quick Configuration Manual 3.38.0 3.3 Changing the user password Switch to the configuration mode LTP-X# configure terminal   Show created users LTP-X(config)# do show users config   Set the new password for admin LTP-X(config)# user admin password XXXX  ...

  • Page 13: Ltp-X Network Parameters Configuration

      LTP-X. Quick Configuration Manual 3.38.0 4 LTP-X network parameters configuration For remote management of LTP-X, you should set network parameters of the device according to the settings of the network that you intend to use. Changing the network parameters of the device is recommended when connecting to the CLI interface through the serial interface.
  • Page 14   LTP-X. Quick Configuration Manual 3.38.0 Apply the configuration LTP-X(switch)(config)# commit LTP-X(switch)(config)# exit LTP-X(switch)# exit   Save the configuration LTP-X# save...

  • Page 15: Olt Ltp-X Firmware Update

    Reboot the device LTP-X# reboot Do you really want to reboot the system now? (y/n) After LTP-X loading, the firmware version can be found by the command show version:  LTP-X# show version Eltex LTP-8X:rev.C software version 3.32.0 build 2473 on 23.08.2018 17:09...

  • Page 16: Snmp, Syslog, Ntp, Ip Source Guard Services Configuration

      LTP-X. Quick Configuration Manual 3.38.0 6 SNMP, SYSLOG, NTP, IP Source GUARD services configuration 6.1 SNMP configuration SNMP – SNMP is used for monitoring and management of network devices. Switch to the configuration mode LTP-X# configure terminal   Enable SNMP LTP-X(config)# ip snmp enable  ...

  • Page 17: Syslog Configuration

      LTP-X. Quick Configuration Manual 3.38.0 6.2 SYSLOG configuration Syslog is a protocol designed for transmission of system event messages and error notifications to remote servers. Switch to the configuration mode LTP-X# configure terminal   Specify the syslog server address LTP-X(config)# logging remote 192.168.205.200  ...

  • Page 18: Ip Source Guard Configuration

      LTP-X. Quick Configuration Manual 3.38.0 Check the NTP settings LTP-X(config)# do show ip ntp Ntp: Enabled: true Ntpserver: 192.168.205.200 Interval: 3600 Timezone: Daylightsaving: false   Apply the configuration LTP-X(config)# do commit   Save the configuration LTP-X(config)# do save 6.4 IP Source Guard configuration Starting with version 3.26.0, OLT supports the IP Source Guard functionality, which allows you to limit the unauthorized use of IP addresses on the network.

  • Page 19: Dhcp_Ra (Broadcast - Unicast Relay) Configuration

      LTP-X. Quick Configuration Manual 3.38.0 6.5 DHCP_RA (broadcast – unicast relay) configuration To reduce the broadcast traffic and avoid responses from illegal DHCP-servers, unicast messages can be configured to interact with the specified DHCP Relay Agent. Relay Agent can be individually started for each separate VLAN.

  • Page 20: Switch Configuration

    LTP-X# save * Command is applicable for: LTP-8Х rev.B HW_revision 2vХ. LTP-8Х rev.С HW_revision 1vХ. For LTP-8X HW_revision 1vX version, the following command applies:  tagged pon-port 0 – 1. For LTP-4X rev.B, LTP-4X rev.C, the following command applies: tagged pon-port 0 –3...
  • Page 21   LTP-X. Quick Configuration Manual 3.38.0 The hardware version of LTP-X can be found using the command: LTP-8X# show system environment System information: CPU load average (1m, 5m, 15m): 0.83 2.35 1.48 Free RAM/Total RAM (Mbytes): 279/495 Temperature (sensor1/sensor2): 35C/48C...

  • Page 22: Igmp Configuration

      LTP-X. Quick Configuration Manual 3.38.0 8 IGMP configuration Enable IGMP SNOOPING globally LTP-X(switch)(config)# ip igmp snooping   VLAN 30 configuration mode LTP-X(switch)(config)# vlan 30   Enable IGMP SNOOPING in VLAN multicast LTP-X(switch)(config-vlan)# ip igmp snooping enable   Enable IGMP proxying LTP-X(switch)(config-vlan)# ip igmp snooping querier enable LTP-X(switch)(config-vlan)# exit  ...

  • Page 23: Cross_Connect, Ports Profiles Configuration For Ont

      LTP-X. Quick Configuration Manual 3.38.0 9 CROSS_CONNECT, PORTS profiles configuration for ONT Switch to the configuration mode LTP-X# configure terminal   Select datapath model 2 LTP-X(config)# gpon olt model 2   Create and switch to the Cross-Connect profile for ONT Internet service LTP-X(config)# profile cross-connect INTERNET LTP-X(config-cross-connect)("INTERNET")#  ...
  • Page 24   LTP-X. Quick Configuration Manual 3.38.0 Specify internal VLAN of the management service in ONT LTP-X(config-cross-connect)("ACS")# user vid untagged   Specify the management service type LTP-X(config-cross-connect)("ACS")# type management LTP-X(config-cross-connect)("ACS")# exit   Create and switch to the multicast profile LTP-X(config)# profile ports NTP-RG  ...

  • Page 25: Pppoe Intermedia Agent, Dhcp Relay Agent - Olt Profiles Configuration

      LTP-X. Quick Configuration Manual 3.38.0 10 PPPoE Intermedia Agent, DHCP Relay Agent - OLT profiles configuration 10.1 PPPoE Intermedia Agent configuration Switch to the configuration mode LTP-X# configure terminal   Create and switch to the profile configuration LTP-X(config)# profile pppoe-ia 1  ...

  • Page 26: Dhcp Relay Agent Configuration

      LTP-X. Quick Configuration Manual 3.38.0 10.2 DHCP Relay Agent configuration...
  • Page 27   LTP-X. Quick Configuration Manual 3.38.0 Switch to the configuration mode LTP-X# configure terminal   Create and switch to the DHCP profile configuration menu LTP-X(config)# profile dhcp-ra 1   Enable Agent LTP-X(config-dhcp-ra)("1")# enable   Send HOSTNAME LTP-X and id ONT in information about which port the request for DHCP relay came from LTP-X(config-dhcp-ra)("1")# overwrite-option82 circuit-id %HOSTNAME%%ONTID%  ...
  • Page 28   LTP-X. Quick Configuration Manual 3.38.0 ONT authentication mode: both Auto reconfigure ONT: true Auto reconfigure GPON-port: true Auto reconfigure OLT: true PLOAM password in alarm: false Auto-activation ONT: false Default template: unassigned With this configuration, for all VLANs except 3149, the DHCP Relay Agent profile 0 will be used. To apply the DHCP-RA profile settings, it is required to reconfigure the OLT chips, if the 'Auto reconfigure GPON-port' parameter of the automatic GPON port reconfiguration is not set in the OLT configuration: true Reconfiguration is performed by the command:...

  • Page 29: Adding And Configuring Ont

      LTP-X. Quick Configuration Manual 3.38.0 11 Adding and configuring ONT It is necessary to add ONT 454C54580800F6B1 to the configuration, to tree 0 ONT ID 1 and assign all the required profiles to it to provide services. View connected but not added ONTs LTP-X# show interface ont 0-7 unactivated ----------------------------------- GPON-port 0 ONT unactivated list...
  • Page 30   LTP-X. Quick Configuration Manual 3.38.0 After executing the commands in section 10 of this manual, it is recommended to reset the terminal to factory settings: LTP-X# send omci restore interface ont 0/1 After rebooting the device, it is necessary to check all services. View a list of connected ONTs added to the configuration LTP-X# show interface ont 0-7 online -----------------------------------...

  • Page 31: Ont Configuration Template

      LTP-X. Quick Configuration Manual 3.38.0 12 ONT configuration template To simplify the configuration of the same type of ONT, you can use a pre-prepared configuration template 'Template', which will subsequently be assigned to the ONT. Switch to the configuration mode LTP-X# configure terminal  ...
  • Page 32 454C54580800F6B1 from Section 10, but to add ONT it is enough to execute only 2 commands.  When viewing the ONT configuration by the [T] markers, it is easy to distinguish the template configuration parameters from the usual ones. LTP-8X(config)(if-ont-0/10)# do show interface ont 0/10 configuration ----------------------------------- [ONT0/10] configuration...

  • Page 33: Configuration Of Ltp For Operation With The Internal Acs Server

    ONTs belonging to this OLT.  LTP-8X with ver.3 software version does not have a built-in ACS server. You can find out the type of OLT model by running the show system environment command, the TYPE field.
  • Page 34   LTP-X. Quick Configuration Manual 3.38.0 Specify the service VLAN of the management service LTP-X(config-cross-connect)("ACS")# outer vid 4094 LTP-X(config-cross-connect)("ACS")# type management   Apply the configuration LTP-X(config-cross-connect)("ACS")# commit   Save the configuration LTP-X(config-cross-connect)("ACS")# save * Command is applicable for:  LTP-8Х rev.B HW_revision 2vХ. LTP-8Х...

  • Page 35: Configuration Of Acs Profile For Ont

    For the convenience of working with ACS profiles for ONT, you can upload the required profile via ftp/tftp protocol. Example: LTP-8x# copy tftp://10.0.0.1/acs-config fs://acs-config  The uploaded configuration should be in the form of executable commands on the OLT to configure the required profile.

  • Page 36: Adding And Configuring A Subscriber Via Acs

      LTP-X. Quick Configuration Manual 3.38.0 15 Adding and configuring a subscriber via ACS (acs)#   Switch to subscriber configuration mode (acs)# user   Add the subscriber IVANOV (acs-user)# add user IVANOV   Switch to the subscriber IVANOV configuration mode (acs-user)# user IVANOV  ...

  • Page 37: Ont Firmware Update Via Acs

    (acs-profile) by the command 'show list' (acs-firmware_config-fw id='1')add profile TEST The next time the ONT contacts ACS, the firmware will update and the ONT will automatically restart. If you have any questions, contact the ELTEX technical support service: e-mail: techsupp@eltex.nsk.ru...

  • Page 38: Appendix A. Example Of Acs Profile For Ntp-Rg14Xxg-W/Ntu-Rg14Xxg-W

      LTP-X. Quick Configuration Manual 3.38.0 17 APPENDIX A. Example of ACS profile for NTP-RG14XXG-W/NTU-RG14XXG-W set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.DHCPServerEnable" "1" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.DomainName" "HomeLAN" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.1.Enable" "1" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface. 1.IPInterfaceAddressingType" "Static" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface. 1.IPInterfaceIPAddress" "192.168.1.1" nocheck set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.
  • Page 39   LTP-X. Quick Configuration Manual 3.38.0 set property "InternetGatewayDevice.Layer2Bridging.Filter.12.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.13.AdmitOnlyVLANTagged" "0" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.13.FilterBridgeReference" "4" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.13.FilterEnable" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.13.FilterInterface" "13" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.13.VLANIDFilter" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.2.AdmitOnlyVLANTagged" "FALSE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Filter.2.FilterBridgeReference"...
  • Page 40   LTP-X. Quick Configuration Manual 3.38.0 set property "InternetGatewayDevice.Layer2Bridging.Marking.2.MarkingEnable" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.2.MarkingInterface" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.2.VLANIDMark" "-1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.2.VLANIDMarkOverride" "FALSE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.2.VLANIDUntag" "TRUE" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.3.EthernetPriorityMark" "3" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.3.MarkingBridgeReference" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.3.MarkingEnable"...
  • Page 41   LTP-X. Quick Configuration Manual 3.38.0 set property "InternetGatewayDevice.Layer2Bridging.Marking.9.MarkingInterface" "9" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.9.VLANIDMark" "30" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.9.VLANIDMarkOverride" "1" nocheck set property "InternetGatewayDevice.Layer2Bridging.Marking.9.VLANIDUntag" "0" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.DigitMap" "x.T" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.DigitMapEnable" "1" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line. 1.PhyReferenceList" "1" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.
  • Page 42   LTP-X. Quick Configuration Manual 3.38.0 set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection. 1.IdleDisconnectTime" "0" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.1.Name" "HSI_PPP" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection. 1.NATEnabled" "1" nocheck...

  • Page 43: Appendix B. Example Of Setting Private Parameters For Ntp-Rg14Xxg/Ntp-Rg14Xxg- W

      LTP-X. Quick Configuration Manual 3.38.0 18 APPENDIX B. Example of setting private parameters for NTP-RG14XXG/NTP- RG14XXG-W set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection. 1.Username" "szt" nocheck set property "InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection. 1.Password" "szt" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line. 1.CallingFeatures.CallerIDName" "111" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line. 1.DirectoryNumber" "111" nocheck set property "InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1.Enable"...

  • Page 44: Appendix C. Rs-232 Null-Modem Cable Pin Designation

      LTP-X. Quick Configuration Manual 3.38.0 19 APPENDIX C. RS-232 null-modem cable pin designation LTP-8X, LTP-4/8X rev.B DB-9 socket                                 DB-9 socket LTP-4/8X rev.C...

  • Page 45: Appendix D. Ont Ntu-1 Configuration

    LTP-8Х rev.B HW_revision 2vХ. LTP-8Х rev.С HW_revision 1vХ. For LTP-8X HW_revision 1vX version, the following command applies:  tagged pon-port 0 – 1 . For LTP-4X rev.B, the following command applies: tagged pon-port 0 – 3. Cross-connect and Ports profile configuration...
  • Page 46   LTP-X. Quick Configuration Manual 3.38.0 Specify the service VLAN for this service LTP-X(config-cross-connect)("NTU1")# outer vid 2149 LTP-X(config-cross-connect)("NTU1")# exit   Create and switch to the profile NTU-1 LTP-X(config)# profile ports NTU1   Add the port in bridge group LTP-X(config-ports)("NTU1")# port bridge group  ...
  • Page 47 LTP-8Х rev.B HW_revision 2vХ. LTP-8Х rev.С HW_revision 1vХ. For LTP-8X HW_revision 1vX version, the following command applies:  tagged pon-port 0 – 1 . For LTP-4X rev.B, the following command applies: tagged pon-port 0 – 3. Cross-connect and Ports profile configuration...
  • Page 48   LTP-X. Quick Configuration Manual 3.38.0 Create and switch to the profile for NTU-1 LTP-X(config)# profile ports NTU1   Add the port 0 in bridge group 20 LTP-X(config-ports)("NTU1")# port 0 bridge group 20   Apply the configuration LTP-X(config-ports)("NTU1")# do commit  ...

  • Page 49: Appendix E. Ont Sfp-Onu Configuration

    LTP-8Х rev.B HW_revision 2vХ. LTP-8Х rev.С HW_revision 1vХ. For LTP-8X HW_revision 1vX version, the following command applies:  tagged pon-port 0 – 1 . For LTP-4X rev.B, the following command applies: tagged pon-port 0 – 3. Cross-connect and Ports profile configuration...
  • Page 50   LTP-X. Quick Configuration Manual 3.38.0 Specify the service VLAN for this service LTP-X(config-cross-connect)("NTU1")# outer vid 2149 LTP-X(config-cross-connect)("NTU1")# exit   Create and switch to the profile SFP-ONU LTP-X(config)# profile ports SFPONU   Add the port in bridge group LTP-X(config-ports)("NTU1")# port bridge group  ...
  • Page 51   LTP-X. Quick Configuration Manual 3.38.0 Add the required VLAN LTP-X(switch)(config)# vlan 100,200   Receive traffic in VLAN from front-port LTP-X(switch)(config-vlan)# tagged front-port   Transmit tagged to all pon ports LTP-X(switch)(config-vlan)# tagged pon-port – LTP-X(switch)(config-vlan)# exit   Apply the configuration LTP-X(switch)(config)# commit LTP-X(switch)(config)# exit LTP-X(switch)# exit...
  • Page 52   LTP-X. Quick Configuration Manual 3.38.0 Save the configuration LTP-X(config-ports)("SFPONU ")# save Adding and configuring ONT SFP-ONU. Switch to the configuration mode LTP-X# configure terminal   Switch to the tree 0 ONT ID 3 LTP-X(config)# interface ont 0/3   Assign the required ONT to this position LTP-X(config)(if-ont-0/3)# serial 454C545862000078  ...
  • Page 53   LTP-X. Quick Configuration Manual 3.38.0 • Step 2. Configure cross-connect profiles. LTP-X(config)# profile cross-connect cc-tunnel LTP-X(config-cross-connect)("cc-tunnel")# bridge LTP-X(config-cross-connect)("cc-tunnel")# bridge group 10 LTP-X(config-cross-connect)("cc-tunnel")# tag-mode tunnel LTP-X(config-cross-connect)("cc-tunnel")# exit LTP-X(config)# profile cross-connect "cc-selecttunnel" LTP-X(config-cross-connect)("cc-selecttunnel")# bridge LTP-X(config-cross-connect)("cc-selecttunnel")# bridge group 10 LTP-X(config-cross-connect)("cc-selecttunnel")# tag-mode selective-tunnel LTP-X(config-cross-connect)("cc-selecttunnel")# exit LTP-X(config)# profile cross-connect "cc-single"...

  • Page 54: Appendix F. Ont/Gpon Interface Status Table

      LTP-X. Quick Configuration Manual 3.38.0 22 APPENDIX F. ONT/GPON interface status table ONT status description ONT status Description UNACTIVATED ONT has no configurations ALLOCATED ONT detected AUTHINPROGRESS ONT authentication is in progress AUTHFAILED Authentication failed AUTHOK Authentication successfully completed PRECONFIG Preparing ONT for configuration CFGINPROGRESS...
  • Page 55   LTP-X. Quick Configuration Manual 3.38.0 Value Description FAILED The channel is out of operation DISABLED The channel is disabled...

This manual is also suitable for:

Ltp-4x

Table of Contents