Related Manuals for ELTEX Eltexalatau MA4000-PX
Summary of Contents for ELTEX Eltexalatau MA4000-PX
- Page 1 MA4000-PX (v. 3.24.0) Operation Manual Appendix MA4000-PX Quick Setup Guide (v.3.24.0) Subscriber access and aggregation node...
-
Page 2: Table Of Contents
____________________________________________________________________________________ TABLE OF CONTENTS Abstract ................................3 Connection methods for Command Line Interface (CLI) ..................4 Telnet/SSH connection ..........................4 Serial port connection (console) ......................... 4 Changing user password ..........................5 Adjustment of PP4X network settings ......................... 5 PP4X Board VLAN Configuration .......................... 6 Configuration of SNMP and SNTP services ...................... -
Page 3: Abstract
____________________________________________________________________________________ ABSTRACT This operation manual describes: Connection methods for MA4000-PX Command Line Interface (CLI) (hereinafter the "device") Adjustment of the device network settings VLAN configuration for provision of various services Configuration of SNMP and SNTP services Automatic configuration upload settings IGMP configuration LACP configuration Creation and editing of ONT profiles: Ports, Cross-Connect... -
Page 4: Connection Methods For Command Line Interface (Cli)
******************************************** Welcome to MA4000 ******************************************** MA4000 login: admin Password: Technical support: http://eltex.nsk.ru/support Thu Mar 3 16:24:54 LOCAL 2016 MA4000# Serial port connection (console) Null modem cable is required for this type of connection. For null modem cable wiring diagram, see Appendix B. -
Page 5: Changing User Password
____________________________________________________________________________________ Technical support: http://eltex.nsk.ru/support Thu Mar 3 16:24:54 LOCAL 2016 MA4000# For security reasons, we recommend to change the default password during the first connection (see Paragraph 2.3 Changing user password). Changing user password To change user settings, enter the Configure view terminal configuration mode using the configure terminal command. -
Page 6: Pp4X Board Vlan Configuration
____________________________________________________________________________________ Set the Synchronization state in the stack parameter to Enabled in the Stack Units table. To configure PP4X module network parameters, enter the configuration mode using the configure terminal command. Define the required network settings. For instance: IP=192.168.205.113, Mask=255.255.255.0, Gateway=192.168.205.230, and specify VLAN for the management network. -
Page 7: Configuration Of Snmp And Sntp Services
____________________________________________________________________________________ CONFIGURATION OF SNMP AND SNTP SERVICES 5.1 SNMP configuration MA4000# configure terminal Enter the configuration mode MA4000(config)# ip snmp agent enable Address of TFTP server for backup MA4000(config)# ip snmp agent traps trapsv2 192.168.205.101 Configure sending traps MA4000(config)# ip snmp agent traps trapsv2 192.168.205.101 Configure sending informs MA4000(config)# ip snmp agent system name MA4000... -
Page 8: Lacp Configuration
____________________________________________________________________________________ LACP CONFIGURATION MA4000# configure terminal Enter the configuration mode MA4000(config)# interface port-channel 1 Select the port-channel MA4000(express-config-port-channel-1)# mode lacp Select the port-channel operation mode MA4000(express-config-port-channel-1)# exit MA4000(config)# interface front-port 1/3-4 MA4000(front-port-1/3-4)# channel-group 1 force Add the required ports into the group MA4000(front-port-1/3-4)# exit MA4000(config)# vlan 2149... -
Page 9: Configuration Cross-Connect And Ports Profiles For Ont
____________________________________________________________________________________ 10 CONFIGURATION CROSS-CONNECT AND PORTS PROFILES FOR Configuration of cross-connect profiles MA4000(config)# profile cross-connect INET Create and go to the Cross-Connect profile for ONT Internet service MA4000(config-cross-connect)("INET")# outer vid 2149 Define the service VLAN for Internet service MA4000(config-cross-connect)("INET")# user vid 10 Define the internal VLAN for Internet service in ONT MA4000(config-cross-connect)("INET")# exit... -
Page 10: Adding And Configuring Ont
____________________________________________________________________________________ in VLAN 30 MA4000(config-ports)("NTP-RG")# igmp multicast dynamic-entry 0 vid 30 configuration of the vlan multicast, which receives the range of the following groups MA4000(config-ports)("NTP-RG")# igmp multicast dynamic-entry 0 group 224.0.0.1 239.255.255.255 Multicast groups range configuration MA4000(config-ports)("NTP-RG")# do commit Apply the configuration MA4000(config-ports)("NTP-RG")# do confirm Confirm the configuration 11 ADDING AND CONFIGURING ONT... -
Page 11: Configuration Of Olt Profiles-Pppoe Intermedia Agent, Dhcp
____________________________________________________________________________________ — 12 CONFIGURATION OF OLT PROFILES PPPOE Intermedia Agent, DHCP Relay Agent 12.1 PPPoE Intermedia Agent Configuration MA4000# configure terminal Enter the configuration mode MA4000(config)# profile pppoe-ia pppoe Add a new profile MA4000(config-pppoe-ia)("pppoe")# enable Enable Agent MA4000(config-pppoe-ia)("pppoe")# sessions-limit 8192 Define the maximum quantity of PPPoE sessions for the profile MA4000(config-pppoe-ia)("pppoe")# sessions-limit per-user 4... -
Page 12: Ma4000-Px Firmware Update
____________________________________________________________________________________ PPPoE Intermedia Agent and DHCP Relay Agent settings will take effect after the OLT chip is reconfigured. MA4000# reconfigure olt slot 7 device 0 Reconfigure OLT chip 0 OLT successfully reconfigured. 13 MA4000-PX FIRMWARE UPDATE Given below are the example of a new firmware version installation. Source data: Firmware file is located on the TFTP server TFTP server IP address 192.168.205.100... - Page 13 ____________________________________________________________________________________ If the command will not be entered in 10 minutes after the unit has booted, the unit will automatically reboot, and image 1 will be selected as the active image. Request complete. MA4000# show firmware Firmware status: ~~~~~~~~~~~~~~~~ Unit Image Running Boot...
Need help?
Do you have a question about the Eltexalatau MA4000-PX and is the answer not in the manual?
Questions and answers