Advertisement
Quick Links
Unpacking ................................................................... 2
Location ...................................................................... 2-3
Programmable Divider & Pump Calculations ........ 4
Dimensions & Weights .............................................. 7
Specifications ............................................................. 10
Parts List ..................................................................... 11
For file reference, please record the following data:
Model No:
Serial No:
Installation Date:
Installation Location:
When ordering replacement parts for your LMI Controller or accessory, please include
the complete Model Number and Serial Number of your unit.
Instruction
Instruction
Instruction
Instruction
Instruction
Remote Flowmeter - Pulser
CONTENTS
Manual
Manual
Manual
Manual
Manual
RFP Series
Replaces same of Rev D 9/96
1538.D 6/97
Advertisement
Related Manuals for LMI RFP Series
Summary of Contents for LMI RFP Series
-
Page 1: Table Of Contents
For file reference, please record the following data: Model No: Serial No: Installation Date: Installation Location: When ordering replacement parts for your LMI Controller or accessory, please include the complete Model Number and Serial Number of your unit. Replaces same of Rev D 9/96 1538.D 6/97... -
Page 2: Unpacking
Programmable Divider complete with 10 feet of cable for charge elevation is higher than the top of the Flowmeter direct connection to an LMI metering pump. (see "Typical Installation" drawing below). B. Remote Flowmeter units in 3/4", 1", and 1 1/2" sizes 5. - Page 3 3/4", 1" or 1 1/2" models. 1. Installation of your LMI metering pump should be in accordance with instructions included with the pump. 10. Air trapped in the Flowmeter should be removed prior to operation.
-
Page 4: Programmable Divider & Pump Calculations
E - Divider number 1. DETERMINE METERING PUMP OUTPUT (GPH*) • Be sure the metering pump selected is an LMI A7, B7 or C7 type pump. These pumps are equipped with an external input jack for use with RFP flowmeters. - Page 5 2. DETERMINE PERCENT OUTPUT REQUIRED FROM PUMP Required pump output from (percent output required from the pump) Max output of metering pump selected (in GPH*) Example B: (Percent output required from pump) 3. DETERMINE THE STROKE SETTING Square Root of (Stroke knob setting on pump and Percent output strokes per minute in step 5)
- Page 6 5. DETERMINE DIVIDER NUMBER NOTE: If an LMI D7 metering pump is being used, multiply value by 75% to determine correct Divider Number. Max. flowrate of water through Primary pulses per flowmeter (in GPM*) U.S. gallon (from chart) Divide number...
-
Page 7: Dimensions & Weights
DIMENSIONS & WEIGHTS Model No. RFP-07 RFP-10 RFP-15 RFP-20 RFP-30 RFP-40 RFP-60 Nominal Size 1-1/2 100) 150) 7.5) 10.25) 11.81) 10.62) 190) 260) 300) 270) 305) 356) 457) 11.34) 14.87) 17.25) 288) 378) 438) 5.35) 5.79) 6.34) 8.6) 8.440) 9.370) 12.560) 136) 147) - Page 8 RFP-07, RFP-10, RFP-15 RFP-20...
- Page 9 RFP-30 RFP-40 RFP-60...
-
Page 10: Specifications
REMOTE PROGRAMMABLE DIVIDER - ALL MODELS SPECIFICATIONS RFP-07, RFP-10, RFP-15, RFP-20 TYPE: Multi-jet Impeller Meter BODY: Bronze REGISTER: Straight reading US Gallons, protected by high impact resistant plastic, permanently hermetically sealed . 7 digit totalizer on RFP-07 and RFP-10 8 digit totalizer on RFP-15, RFP-20 SERVICE TEMPERATURE: 32 to 120 F (0 to 50 MAXIMUM OPERATING PRESSURE: 200 psi (13.8 Bar) -
Page 11: Parts List
PARTS LIST Quantity per Assembly Quantity per Assembly Quantity per Assembly Quantity per Assembly Quantity per Assembly Program. Program. Program. Program. Program. Part Part Divider Divider Part Part Part Divider Divider Divider Description Description Description Description Description RFP-07 RFP-07 RFP-07 RFP-07 RFP-07 RFP-10 RFP-10... - Page 12 © 1996 LMI Milton Roy - All Rights Reserved Printed in USA Specifications subject to change without notice...