Advertisement
Quick Links
Specifications
• Handmade in Italy since 1960
• ¼ Turn valves handmade at
Nicolazzi Factory
• Lead Free Brass Compliant to
AZ/NZS 3718
• Suitable even and uneven
pressure
• Handles are interchangeable
Further information Phone (03) 9761 4603
Single Hole Mixer
Art: Z2606
Available replacement
handles:
El Capitan Handle
-78 Mont Blanc Handle
-78A Mont Blanc Antique
Crackle
-78B Mont Blanc Black
WM22315
AS/NZS3662
Canterbury Sink & Tap Co.
Max/Min Operating
Pressure: 100/500kPa
sales@sinkandtap.com.au
Advertisement
Related Manuals for CANTERBURY Z2606
Summary of Contents for CANTERBURY Z2606
- Page 1 • ¼ Turn valves handmade at Nicolazzi Factory • Lead Free Brass Compliant to AZ/NZS 3718 • Suitable even and uneven pressure WM22315 AS/NZS3662 • Handles are interchangeable Canterbury Sink & Tap Co. Max/Min Operating Pressure: 100/500kPa Further information Phone (03) 9761 4603 sales@sinkandtap.com.au...
- Page 2 Important Notice Model : Z2606 CAREFULLY READ THROUGH THESE INSTRUCTIONS BEFORE INSTALLATION AND USE OF ALL TAP WARE AND WALL VALVES INSTALLATION and WARRANTY INSTRUCTIONS TECHNICAL INFORMATION All flexible hoses are designed and manufactured for use with water in exposed locations only. Do not expose to household cleaners, chlorine, chloride, hydrochloric acid or other corrosive chemicals.
- Page 3 Installation Instructions Model : Z2606 ❶ Preparation Flush out the pipework to remove any foreign matter. Tap cut out hole sizes : Maximum 33mm diameter. Under side clearance : Maximum 55mm ❷ Install the water supply hoses into the body - 1 - Note: Hand tighten only, DO NOT over tighten- 2 ...
- Page 4 Installation Instructions Model : Z2606 ❹ Feed the O-ring 5, over the water supply hoses. Insert the tap into mounting hole. Feed the water supply hoses carefully through the hole ensuring that they are not bent or kinked, as this could result in permanent damage or leakage.
- Page 5 Installation Instructions Model : Z2606 ❻ Check the position on the sink of the tap, then tighten the nut using a 13mm spanner. Note: the under deck mounting surface must be flat. If the mounting surface is irregular, the nut may not be secured, and the tap will be loose on the sink.
- Page 6 Spare Parts list Model : Z2606 Further information Phone (03) 9761 4603 sales@sinkandtap.com.au...
- Page 7 Care and Maintenance Instructions Model : Z2606 Removing and replacing a handle MODEL SHOWN : Z2606 Unscrew the retaining screw with a Phillips ❶ Using a box cutter or similar sharp edged ❷ head screw driver. tool, carefully remove the indice button.
- Page 8 Care and Maintenance Instructions Model : Z2606 MAINTENANCE FOR SINGLE HOLE/TWO LEVER TAP WARE WITH TWO LEVER DESIGN INSTRUCTIONS FOR REPLACEMENT OF THE HO T OR COLD CARTRIDGE Do not replace the cartridge if there is low flow or no flow. Low flow or no flow is caused by obstruction or kinking of supply hoses.
- Page 9 Care and Maintenance Instructions Model : Z2606 LOW FLOW OR NO FLOW TROUBLESHOOTING INSTRUCTIONS Current kitchen taps have a max flow rate of 7 Litres per minute from the aerator and the hand spray. If you are experiencing low flow from the spout: Do not change the cartridge •...
- Page 10 Care and Maintenance Instructions Model : Z2606 Care of external finishes Nicolazzi products are all authentic finishes that have not been coated with any product. After each use, pat the fixture down to remove any excess water. This will prevent any water spotting or mineral build-up. Use only soft liquid soap and water to clean the surface.