Advertisement
Quick Links
Specifications
• Handmade in Italy since 1960
• ¼ Turn valves handmade at
Nicolazzi Factory
• Lead Free Brass Compliant to
AZ/NZS 3718
• Suitable even and uneven
pressure
• Handles are interchangeable
Further information Phone (03) 9761 4603
Built-in stop cock 1/2' 1 x PAIR
Art: Z3312--44
ARENA
WM22315
AS/NZS3662
Canterbury Sink & Tap Co.
Max/Min Operating
Pressure: 100/500kPa
sales@sinkandtap.com.au
Available replacement
handles:
-- 44 Handle
--56 Leva Arena
Advertisement
Related Manuals for CANTERBURY ARENA Z3312-44
Summary of Contents for CANTERBURY ARENA Z3312-44
- Page 1 • ¼ Turn valves handmade at Nicolazzi Factory • Lead Free Brass Compliant to AZ/NZS 3718 • Suitable even and uneven pressure WM22315 AS/NZS3662 • Handles are interchangeable Canterbury Sink & Tap Co. Max/Min Operating Pressure: 100/500kPa Further information Phone (03) 9761 4603 sales@sinkandtap.com.au...
- Page 2 Important Notice Model : Z3312--44 CAREFULLY READ THROUGH THESE INSTRUCTIONS BEFORE INSTALLATION AND USE OF ALL TAP WARE AND WALL VALVES INSTALLATION and WARRANTY INSTRUCTIONS TECHNICAL INFORMATION All tapware washers and O-rings are designed and manufactured for use with water. Do not expose to household cleaners, chlorine, chloride, hydrochloric acid or other corrosive chemicals.
-
Page 3: Installation Instructions
Installation Instructions Model : Z3312--44 Z3312--44 WALL TAP ASSEMBLY A small amount of silicon can be applied behind the flange to hold it in place. Continue……. Further information Phone (03) 9761 4603 sales@sinkandtap.com.au... - Page 4 Installation Instructions Model : Z3312--44 ❶ Preparation Flush out the pipework to remove any foreign matter. Tap cut out hole sizes : Maximum 45mm diameter. Not supplied:-Shower breech 200mm centre to centre ❷ Install the C-tech ¼ turn cartridge 1, into the breech seat 2.
- Page 5 Installation Instructions Model : Z3312--44 ❹ Fit the collar 5, onto the locknut outer thread. ❺ Ensure that the locknut is adequately tightened Slide the cover flange 6, over the collar 5, until the against the breech face to prevent any water cover flange sits firmly on the finished/tiled surface.
- Page 6 Installation Instructions Model : Z3312--44 ❼ Ensure the Hot and Cold water cartridges are installed correctly. Hot water cartridge : C-teck 11047 Cold water cartridge: C-teck 11147 Before use Turn on the Hot and Cold supplies to the tap. ...
- Page 7 Spare Parts list Model : Z3312--44 Further information Phone (03) 9761 4603 sales@sinkandtap.com.au...
- Page 8 Care and Maintenance Instructions Model : Z3312--44 Removing and replacing a handle MODEL SHOWN :Z3312 ❶ ❷ Loosen and unscrew the retaining flange Once totally loose, simply remove the A, from the tap body. handle from cartridge spline. ❸...
- Page 9 Care and Maintenance Instructions Model : Z3312--44 LOW FLOW OR NO FLOW TROUBLESHOOTING INSTRUCTIONS Current bathroom taps have a max flow rate of 7 Litres per minute from the aerator and the hand spray. If you are experiencing low flow from the spout: Do not change the cartridge •...
- Page 10 Care and Maintenance Instructions Model : Z3312--44 Care of external finishes Nicolazzi products are all authentic finishes that have not been coated with any product. After each use, pat the fixture down to remove any excess water. This will prevent any water spotting or mineral build-up. Use only soft liquid soap and water to clean the surface.