Page 1
Argon Cube NMARCUBE INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE. CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE. CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
TABLE OF CONTENTS Please read and carefully follow all of the instruction found in this manual. The instructions included here will assure that you have many years of dependable and enjoyable service from your Stanley product. IMPORTANT INSTRUCTIONS ............................UNPACKING AND TESTING THE APPLIANCE ......................
IMPORTANT INSTRUCTIONS PLEASE RETAIN THIS USER GUIDE FOR FUTURE REFERENCE When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1) Read all instructions before using this fireplace 2) The fireplace is hot when in use.
UNPACKING AND TESTING APPLIANCE Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located 240 Volt grounded outlet. Test all aspects of its operation (manual switches, remote and heater) to make sure all components operate correctly.
NMARCUBE Description ELECTRIC FIREPLACE Voltage 230V ac 50Hz Watts 1900W Max NO HEATER MOTOR HEATER Appliance Width 19 5/8" or 500 mm Appliance Height 25 1/4" or 641 mm Appliance Depth 11 3/4" or 300 mm Gross Weight 50.7 lbs or 22 kgs Plug Location Left side Cord Length...
INSTALLATION WALL-MOUNT MOUNT NOTE: Due to the many different materials used on different walls, it is highly recommended NOTE: Due to the many different materials used on different walls, it is highly recommended NOTE: Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance.
Page 7
INSTALLATION ARGON CUBE LEGS 1. Screw the base legs to the steel Screw the base legs to the steel panel. 3. Place the unit onto the base leg the unit onto the base leg and screw in the adjustable feet, fixing the unit and in the adjustable feet, fixing the unit and the base leg.
MEDIA OPTIONS The media that come with this appliance are STEP 3: Remove the front glass panel to decorate your fireplace. Pour the decorative Oak Log Set, Clear glass, Suntea glass and media into the tray. Feel free to use any White Vermiculite.
OPERATION The Fireplace operates by using either the touch panel located on the upper left hand corner or by remote control. Plug the fireplace into a 15 Amp wall socket. Plug the fireplace into a 15 Amp wall socket. MANUAL OPERATION 1.
REMOTE CONTROL OPERATION For remote to function make sure the fireplace is plugged in and the remote has batteries. Important: When operating the remote make sure you point the remote to the center of the fireplace. Each time you press the button, the buzzer inside the unit will beep once. It takes some time for the receiver to respond to the transmitter.
Page 11
third time to turn on the AUTO mode, press to set the temperature to switch temperature unit between Celsius and Fahrenheit. Press this button to adjust the speed of the flame. There are 3 options: High- Medium- Low. Press this button to turn on and off the ember bed light. When in ON position, the display screen of the remote control shows AD 1, when the number “1”...
Page 12
When the 7 day timer’s set, the icon will be displayed on the LCD screen of the remote control. Press again to cancel the 7 da y timer and the icon will disappears. NOTE: If the 7 day timing and the general timing are set at the same time, the system will respond to an earlier shutdown time.
WIFI OPERATION INSTALL TuyaSmart life There are 2 ways to install TuyaSmart; 1. Search for “TuyaSmart life” in the APP store on your phone, download and install. 2. Scan the QR code below with your mobile phone. WIFI SETTING AND FIREPLACE OPERATION 1.
Page 14
FIG.4 3. Press (flame button) on the touch panel of the fireplace for more than 5 seconds when the fireplace in standby mode. There will be 2 beeps come out from the fireplace and the (flame button) will flash as well indicating that Wi-fi is in EZ mode. Then please confirm to go next.
Page 15
6. Now you are in the interface like FIG.7. You can operate the fireplace via Wi-fi. FIG.7 NOTE: Turn off the flashing blue Wifi indicator light Touch the (power button) once, the blue light will stop flashing.
CARE AND MAINTENANCE 1. Switch off and unplug from the power supply before cleaning. 2. Using a soft, moist cloth, with or without a mild soap solution, carefully clean the exterior surface of the products. CAUTION: Allow the product to completely cool before handling or cleaning it. 3.
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Dim or no flame Flame LED’s are burnt out. Inspect the LED’s and replace them if necessary. Back black cloth is falling off Change a flicker and back black cloth. and rolled up in the flicker. Ember Ember LED’s are burnt out Inspect the ember bed LED’s and...
SERVICE HISTORY This heater must be serviced annually depending on usage. Date Dealer Service technician Service Performed Special Concerns Name Name NOTES:...
All warranty claims must be reported to the Waterford Stanley Service Department and must be submitted with the product serial number (located on the front of this manual), date of purchase, proof of purchase (if requested) and details of the specific nature of the problem.