Invixium INGUIDE SENSE 2 Quick Start Manual

SENSE 2
Invixium Customer Portal
Stay up to date with:
▪ Latest Updates
▪ Best Practices
▪ Datasheets
▪ Installation Guides
▪ Feature Description Documents
▪ Videos
▪ FAQs
▪ Tutorials
▪ And more...
Visit https://www.invixium.com/support/

In the Box

Dolphin Crimps
(qty 12)
Earth Ground Wire

Getting Started

1 Remove the Mounting Plate, Wired Back
Cover and Screws from the IXM INSTALL KIT.
2 Install the Mounting Plate at the desired
location. Invixium recommends 120 cms
from the floor to the bottom of the device.
3 Make the necessary connections to the Wired
Back Cover (refer to
4 Unscrew and remove the Temporary Back
Cover from the device and connect the
Wired Back Cover using the same screws.
5 Hang your device on the Mounting Plate
and secure it on the bottom with the screw
provided.
Get Wired Glossary
ACP
Access Control Panel
COM Common
DAC
Door Access Control
DSP Door Strike Power
EGND Earth Ground
GND Ground
LED Light Emitting Diode
NC
Normally Closed
NO Normally Open
PoE Power over Ethernet
Get Wired Top Connector
Wire Color Wire
White/Red
Grey
Grey/Red
Brown
Yellow
Black/Yellow
White/Purple
Purple/Yellow
Blue/White
Black/White
Get Wired Bottom Connector
Wire Color Wire
Red
Black
Green/Yellow
RJ45
Receptacle
Earth Ground
For protection against Electrostatic Discharge, Invixium recommends the
use of a ground connection between each IXM device to a high quality
Earth Ground available at the install site.
Connect to Earth Ground in the following way:
1 Connect the green and yellow earthing wire from the wired back
cover (bottom connector PIN 5) to the building earthing.
2 Connect the open end of earth ground wire provided in the Install Kit
Box to the building earthing as well.
3 Screw the lug end of the earth ground wire to the metal mounting plate.
4 Ensure all Earth Ground connections are made to each device prior to
turning on the power.

Power It Up

When using an external power supply, ensure that the
regulated, filtered and dedicated power source (Safety
tested, FCC/IC/CE certified) provides a minimum of
1.5A @ 12 VDC.
When using PoE, an IEEE 802.3af compliant Active
Midspan Injector is required (sold separately). Refer to
table for Invixium recommended PoE Injector specs.
Full PoE deployments should include a centralized
PoE PSE. Both IEEE 802.3af power transmission
modes (A and B) are supported. Invixium
recommends the use of battery back up or a UPS
with built-in surge protection.
Note: MYCRO models do not support PoE.
SENSE 2 and TOUCH 2 models support PoE as well as PoE+.
WARNING: Product Warranty is void if improper power (under or over) is supplied to the device.

Ethernet and Wi-Fi

For Ethernet communication, a specific range
of allowable IP addresses can be set for
improved security.
For Wi-Fi communication on
(selected models only), 802.11 b/g/n protocols
are supported. DHCP is enabled as a factory
default. WEP, WPA and WPA2 encryption
options are available.
RS-485 Configuration
For RS-485 networks, ensure that
of 31 devices. At a baud rate of 9600 bps, make certain that the maximum cable length is not longer
than 1200 m (4000 ft).
MYCRO
R = 120 ohms for Standard RS-485 Cabling
R = 100 ohms for CAT5/6 Cabling
MYCRO
TOUCH 2
Wall Mounting Screws
(qty 4)
Metal Mounting
Plate Screw
(qty 1)
Hex Key
Metal Mounting
Plate
Get Wired Pages).
RLY
RX
SGND
SPI
SPO
TX
WDATA
WGND
VIN+
VIN-
Label
RLY_NC
RLY_COM
RLY_NO
ACP_LED1
ACP_LED2
ACP_LED_GND
DAC_IN1
DAC_IN2
DAC_IN3
DAC_GND
Label Pin(s)
VIN+
VIN-
EGND
TCP/IP 9,11,13,
15,17,19
TOUCH 2
IXM devices are wired in a daisy chain configuration, up to a maximum
TOUCH 2
SENSE 2
Quick Start Guide
IXM INSTALL KIT
Snubber Diode
Micro USB Extension
Cable (4 ft/1.2m)
Ferrite Core
(Selected variants only)
Relay
Receiver
Signal Ground
Specific Purpose Input
Specific Purpose Output
Transmitter
Wiegand Data
Wiegand Ground
Power (12VDC)
Power Ground
Pin(s) Wire Color
1 Orange/Yellow
3 Yellow/Green
5 Green/Orange
7 Black/Orange
9 Yellow/Cyan
11
Cyan/Brown
13 Brown/Yellow
15 Black/Cyan
17 Orange
19 Purple
Wire Color
1 Orange/White
3
Purple/White
5 Black/Red
Blue
Blue/Black
Green/White
White/Black
Green
White
Black/Green
INVIXIUM
Input Voltage
Input Current
Output Voltage
Output Current
Power
Router connected
to LAN/WAN
MYCRO
RS-485 to USB
Converter
INGUIDE
Wired Back Cover
USB Cover Screw
Gangue Box
(qty 1)
Mounting Screws
SENSE 2 & TOUCH 2 Only
Top Connector
1 3 5 7 9 11 13 15 17 19
2 4 6 8 10 12 14 16 18 20
Bottom Connector
1 3 5 7 9 11 13 15 17 19
2 4 6 8 10 12 14 16 18 20
Wire Label
SPO_1
SPO_2
SPO_3
SPO_GND
SPI_1
SPI_2
SPI_3
SPI_GND
DAC_OUT
DAC_DSP
Wire Label
RS232_RX
RS232_TX
SGND
RS485+ (B)
RS485- (A)
WDATA_IN0
WDATA_IN1
WDATA_OUT0
WDATA_OUT1
WGND
Earthing Wire from
Wired Cover (PIN 5)
Earth Ground Connections
recommended PoE Injector Specs
90-264 VAC, 60 Hz
0.4 A @ 100 VAC
48 VDC
0.32 A
15.36 Watt
IXM WEB
SENSE 2
IXM WEB
Bottom Connecter RS-485
SGND (6)
RS-485+ (8)
RS-485- (10)
(qty 2)
Pin(s)
2
4
6
8
10
12
14
16
18
20
Pin(s)
2
4
6
8
10
12
14
16
18
20
Earth Ground
Wire Lug
Building Earthing
TOUCH 2