Related Manuals for Nice FGR-223
Summary of Contents for Nice FGR-223
- Page 1 Nice Roll-Control Roll and lamellas control EN - Instructions and warnings for installation and use...
-
Page 2: Warnings And General Precautions
• CAUTION! – This manual contains important instructions and warnings for personal safety. Carefully read all parts of this manual. If in doubt, suspend installation immediately and contact the Nice Technical Assistance. • CAUTION! – Important instructions: keep this manual in a safe place to enable future product maintenance and disposal pro- cedures. -
Page 3: Electrical Connections
3.1 - Electrical connections Carefully follow all the connection instructions. If you have any doubts do not make experiments but consult the relevant technical specifications which are also available on the web site: www.niceforyou.com. Connecting the Roll-Control in a manner inconsistent with this manual may cause risk to health, life or material damage. - Page 4 3.5 - Installation with blinds with built-in driver: Switch off the mains voltage (disable the fuse). Open the wall switch box. Connect with the following the diagram. Verify if the device is connected correctly. Arrange the device and its antenna in a wall switch box. Close the wall switch box .
-
Page 5: Adding The Device
ADDING THE DEVICE Adding (Inclusion) - Z-Wave device learning mode, allowing to add the device to existing Z-Wave network. 4.1 - Using the manual method To add the device to the Z-Wave network manually: 1. Power the device. 2. Identify the S1 switch. 3. - Page 6 6.1 - Standard roller blind positioning - Calibration using connected momentary switch Make sure: • the device is supplied, • momentary switch is connected to S1 and S2 terminals, • the device added to the Z-Wave network, • parameter 151 is set to 1 or 2. Press and hold switch for at least 3 seconds Press and hold the same switch again for at least 3 seconds.
- Page 7 OPERATING ROLLER BLINDS The device allows for connecting switch to the S1 and S2 terminals. These may be momentary (recommended) or toggle switches. Switch buttons are responsible for managing the blind’s movement. Table A2 - Switch types Type Behavior Momentary switch After releasing the switch a spring automatically pushes back and disconnects the switch) Toggle Switch Operates as a two-position switch, it has no spring that would set one position of the switch.
-
Page 8: Resetting The Device To Factory Defaults
RESETTING TO FACTORY DEFAULTS Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. Note. Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use reset procedure only if the primary controller is missing or inoperable. - Page 9 Table A3 - Association groups mapping Root Endpoint Association Group in Endpoint Association Group 2 Endpoint 1 Association Group 2 Association Group 3 Endpoint 2 Association Group 2 Table A4 - Switch Multilevel commands sent to association groups for parameter 151 equal to 1, 5 or 6 Parameter 20 Endpoint Click...
- Page 10 Z-Wave range tester signalling modes: Visual indicator pulsing green - the device attempts to establish a direct communication with the main controller. If a direct communication attempt fails, the device will try to establish a routed communication, through other modules, which will be signalled by visual indicator pulsing yellow.
- Page 11 TRANSPORT_SERVICE [0x55] VERSION [0x86] MANUFACTURER_SPECIFIC [0x72] DEVICE_RESET_LOCALLY [0x5A] POWERLEVEL [0x73] SECURITY [0x98] SECURITY_2 [0x9F] SUPERVISION [0x6C] METER [0x32] CONFIGURATION [0x70] CRC_16_ENCAP [0x56] NOTIFICATION [0x71] PROTECTION [0x75] MULTI_CHANNEL [0x60] CENTRAL_SCENE [0x5B] FIRMWARE_UPDATE_MD [0x7A] APPLICATION_STATUS [0x22] BASIC [0x20] Table A9 - Multichannel Command Class Endpoint 1 ZWAVEPLUS_INFO [0x5E] SWITCH_MULTILEVEL [0x26]...
-
Page 12: Advanced Parameters
[0x02] [0x01] ADVANCED PARAMETERS Roll-Control allows to customize its operation to user’s needs. The settings are available in the NICE interface as simple options that may be chosen by selecting the appropriate box. Table A13 - Roll-Control - Advanced parameters... - Page 13 Available settings: 0 - default (Q1 - 1st channel, Q2 - 2nd channel) 1 - reversed (Q1 - 2nd channel, Q2 - 1st channel) 1 [byte] Default setting: Parameter size: Parameter: 30. Alarm configuration - 1st slot Description: This parameter determines to which alarm frames and how the device should react. The parameters consist of 4 bytes, three most significant bytes are set according to the official Z-Wave protocol specification.
- Page 14 Available settings: 1B [MSB] - Notification Type 2B - Notification Status 3B - Event/State Parameters 4B [LSB] - action: 0 - no action 1 - open blinds 2 - close blinds [0x02, 0xFF, 0x00, 0x00] Default setting: (CO Alarm, any notification, no action) 4 [bytes] Parameter size: Parameter:...
- Page 15 Available settings: 0 - periodic reports are disabled 30-32400 (30-32400s) - report interval 3600 (1h) 2 [bytes] Default setting: Parameter size: Parameter: 65. Energy reports - on change Description: This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller.
-
Page 16: Technical Specifications
The product Roll-Control is produced by Nice S.p.A. (TV). Warnings: - All technical specifications stated in this section refer to an ambient temperature of 20 °C (± 5 °C) - Nice S.p.A. reserves the right to apply modifications to the product at any time when deemed necessary, while maintaining the same functionalities and intended use. -
Page 17: Product Disposal
Caution! – local legislation may envisage serious fines in the event of abusive disposal of this product. DECLARATION OF CONFORMITY Hereby, Nice S.p.A., declares that the radio equipment type Roll-Control is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.niceforyou.com/en/support... - Page 18 Nice SpA Oderzo TV Italia www.niceforyou.com info@niceforyou.com...